11. Arectangular sign of mass 50.0 kg and width w = 5.00 m and e = length 4.00 m is hanging from a hinge and a rope as shown in the figure below. The rope makes and angle 0 = 65.0° with the right wa. (a) Find the tension in the rope. (b) Find the horizontal and vertical components of the hinge force.

11. Arectangular sign of mass 50.0 kg and width w = 5.00 m and e = length 4.00 m is hanging from a hinge and a rope as shown in the figure below. The rope makes and angle 0 = 65.0° with the right wa. (a) Find the tension in the rope. (b) Find the horizontal and vertical components of the hinge force.

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter12: Static Equilibrium And Elasticity

Section: Chapter Questions

Problem 12.8CYU: Check Your Understanding A 400.0-N sign hangs from the end of a uniform strut. The strut is 4.0 m...

See similar textbooks

Similar questions

Suppose the weight of the drawbridge in Figure 9.34 is supported entirely by its hinges and the opposite shore, so that its cables are slack. (a) What fraction of the weight is supported by the opposite shore if the point of support is directly beneath the cable attachments? (b) What is the direction and magnitude of the force the hinges exert on the bridge under these circumstances? The mass of the bridge is 2500 kg.
In order to get his car out of the mud, a man ties one end of a rope to the front bumper and the other end to a tee 15 m away as shown below. He then pulls on the center of the rope with a force of 400 N, which causes its center to be displaced 0.30 m, as shown. What is the force of the rope on the car?
A 15.0-in uniform ladder weighing 500 N rests against frictionless wall. The ladder makes a 60.0 angle ESI with the horizontal, (a) Find the horizontal and vertical forces the ground exerts on the base of the ladder when an 800-N firelighter has climbed 4.00 m along the ladder from the bottom, (b) If the ladder is just on the verge of slipping when the firefighter is 9.00 m from the bottom, what is the coefficient of static friction between ladder and ground?
A wooden door 2.1 m high and 0.90 m wide is hung by two hinges 1.8 m apart. The lower hinge is 15 cm above the bottom of the door. The center of mass of the door is at its geometric center, and the weight of the door is 260 N, which is supported equally by both hinges. Find the horizontal force exerted by each hinge on the door.
A uniform horizontal strut weighs 400.0 N. One end of the strut is attached to a hinged support the wall and the other end of the strut is attached to a sign that weighs 200.0 N The strut is also supported by a cable attached between the end of the strut and the wall. Assuming that the entire weight of the sign is attached at the very end of the s find the tension in the cable and the force at the hinge of the strut.
Explain the need for tall towers on a suspension bridge to ensure stable equilibrium.
In Figure 9.21, the cg of the pole held by the pole vaulter is 2.00 m from the left hand, and the hands are 0.700 m apart. Calculate the force exerted by (a) his right hand and (b) his left hand. (c) If each hand supports half the weight of the pole in Figure 9.19, show that the second condition for equilibrium (net =0 ) is satisfied for a pivot other than the one located at the center of gravity of the pole. Explicitly show how you follow the steps in the Problem-Solving Strategy for static equilibrium described above. Figure 9.21 A pole vaulter is holding a pole horizontally with both hands. The center of gravity is to the left side of the vaulter.
Two thin rods, one made of steel and the other of aluminium, are joined end to end. Each rod is 2.0m long and has cross-sectional area 9.1mm2 . If a 10,000N tensile force is applied at each end of the combination, find: (a) stress in each rod; (b) strain in each rod; and, (c) elongation of each rod.
A 5.45-N beam of uniform density is 1.60 m long. The beam is supported at an angle of 35.0 by a cable attached to one end. There is a pin through the other end of the beam (Fig. P14.30). Use the values given in the figure to find the tension in the cable. FIGURE P14.30
A sandwich board advertising sign is constructed as shown in Figure 9.35. The sign's mass is 8.00 kg. (a) Calculate the tension in the chain assuming no friction between the legs and the sidewalk. (b) What force is exerted by each side on the hinge?
A horizontal plank 4.00 m long and having mass 20.0 kg rests on two pivots, one at the left end and a second 1.00 m from the right end. Find the magnitude of the force exerted on the plank by the second pivot. (See Section 8.4.)
Alarge uniform cylindrical steel rod of density =7.8g/cm3 is 2.0 m long and has a diameter of 5.0 cm. the rod is fastened to a concrete floor with its long axis vertical.what is the normal stress in the rod at the cross-section located at (a)1.0 mfrom its lower end?(b)1.5 m from the lower end?