Answered: 4] The members of a truss are pin…

4] The members of a truss are pin connected at joint O. Determine the magnitude of F, and its angle e for equilibrium. Set F = 6 kN. 5 kN 70 30 7kN 11

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter9: Statics And Torque

Section: Chapter Questions

Problem 7CQ: Explain the need for tall towers on a suspension bridge to ensure stable equilibrium.

See similar textbooks

Related questions

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

Q: 17-45. The drop gate at the end of the trailer has a mass of 1.25 Mg and mass center at G. If it is…

Q: Could a ladder on a level floor lean against a wall in static equilibrium if there were no friction…

Q: •3–5. The members of a truss are connected to the gusset plate. If the forces are concurrent at…

Q: 1000 lb trunch the black resting on the incline plan has a mass of 60g. determine maximum and…

A: There are 4 forces, the push P, weight mg, a normal force N, and a frictional force Ff. The…

Q: 4/31 Determine the forces in members GH and CG for the truss loaded and supported as shown. Does the…

Q: A 3.0 m-long weightless beam is supported at each end by cables. A painter weighing 900 N stands 1.0…

Q: 1. Find the tension in both ropes and the force exerted by the hinge on the horizontal beam. The…

A: As per our guidelines, we are supposed to answer only first one question in case of multiple…

Q: In the fig. shown, compute the ff : (11-13) the tension in cable BD 7.5 rt Tuo = (14-15) the…

A: Since you have posted multiple questions, as per our policy only the first question will be answer.…

Q: The resultant of three parallel loads is 30ON acting at 7m to the right of A. Compute the magnitude…

Q: The bones of the forearm (radius and ulna) are hinged to the humerus at the elbow. The biceps muscle…

Q: Ex. 1.6 The 600-N force applied to the bracket at A is to be replaced by two forces, F in the a-a…

Q: Problem 4.3 The uniform, horizontal beam shown in Fig. 4.50 is hinged to the ground at point A and…

Q: 3) What are the support forces acting on the 100lb cylinder when it is in static equilibrium. Fig…

A: Given Mass of the cylinder = 100 lb Cylinder is in static equilibrium We have to calculate support…

Q: The bones of the forearm (radius and ulna) are hinged to the humerus at the elbow. The biceps muscle…

Q: 2. Rigid-Body in Equilibrium. A nonuniform beam 4.50 m long and weighing 1,000 N makes an angle of…

Q: 7. A 175 lb person stands 3.00 ft. from the end of a 8.00 ft. board. What is the upward force of the…

A: Given Person weight = 175 lb Distance of person from end of board = 3.00 ft We uave to calculate…

Q: A woman is balancing on a high wire which is tightly strung, as shown in Fig. 9–45. The tension in…

Q: 12 If block B weighs 200 lb and block C weighs 100 lb, determine the required weight of block D and…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: A 3 m long weightless beam is supported at each end by cables. A painter weighing 900 N stands 1 m…

A: Given data: Length of beam is, L=3 m. Weight of painter is, Wp=900 N. Distance of painter from left…

Q: Calculate the forces in members BE and BD of the loaded truss. The forces are positive if in…

Q: 3. A uniform plank ABC of weight 30 N and 2 m long is supported at one end A and at a point B 1.4 m…

A: Given that the weight of the plank is F = 30 N 30(1.4-1) = W(0.6)(30)(0.4) = 0.6WW = 120.6W = 20 N

Q: A 40 kg block is placed on an inclined plane whose base is double its height. Determine the force to…

Q: Determine the resultant R (single equivalent force) of the three forces acting on the simple truss.…

Q: What are the magnitude and direction of the force exerted by the wall on the beam in Fig. 5.25? Also…

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

A: in this question we determine angle between AB and AC

Q: 25. A uniform ladder 4.8 m ft long and weighing W lb is placed with one end on the ground and the…

A: Given data: Length of ladder, l=4.8 m Angle of friction, ϕ=200

Q: 1. Find the distance x (measured along AB) at which a horizontal force of 60 lb should be applied to…

Q: (II) Assume the supports of the uniform cantilever shown in Fig. 9–76 (m = 2900 kg) are made of…

A: Let W and g denote the cantilever’s weight (acting downwards at the cantilever’s center) and the…

Q: The bracket is fastened to the girder by means of the two rivets A and B and supports the 2-kN…

A: Given data: Force F = 2 kN The center line force distributed at point A and B in the same direction…

Q: (II) Two cords support a chandelier in the manner shownin Fig. 9–4 except that the upper cord makes…

A: Given data: Angle made by the upper cord with the ceiling is θ=450 Tension on the cords, T=1660 N

Q: Two wires of same length and material but different radii are suspended from a rigid support. Both…

A: Given that, the length of the two wires are same, and the radii are different.Write the expression…

Q: If the tension developed in each of the four wires is not allowed to exceed 600N, determine the…

Q: The mobile in Fig. 12–74 is in equilibrium. Object B has mass of 0.748 kg. Determine the masses of…

A: Given:- The figure is in equilibrium. Object B has a mass = 0.748 kg Find:- Determine the mass of…

Q: (II) A uniform steel beam has a mass of 940 kg. On it is resting half of an identical beam, as shown…

A: Given: The mass of the beam is 940 kg.

Q: a uniferim rod AB is weighs SN. what is necessary to produced equilibrium c from A) ? Cand 5N A I 20…

A: Given: We need to find force F at distance x cm from point A to keep this rod in equilibrium.

Q: A uniform ladder weighing 490 N rests against a frictioniess wall. The ladder has a length L = 14.0…

Q: The ladder has a uniform weight of 80 lb and rests against the wall at B. If the coefficient of…

A: Analyze the following FBD of the ladder. For the ladder to not slip, it should be in static…

Q: •19 To crack a certain nut in a nutcracker, forces with magnitudes of at least 40 N must act on its…

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

Q: -. A uniform ladder I = 10.0 m long and weighing W = 41.3 N rests against a smooth vertical wall. If…

A: The situation is shown below.

Q: 2. A light string ABCDE whose extremity A is fixed, has weights W1 and W2 attached to it at B and C.…

A: (i) Let the tension in AB is T'', in BC is T' and in CD is T. T = 300 N Use Lami's theorem at C.…

Q: A 3 kg ladder is leaning on a wall. If a load P-30 N is applied vertically on the ladder as shown on…

A: The free body diagram is drawn below.

Q: A bungee jumper momentarily comes to rest at the bottomof the dive before he springs back upward. At…

A: The bungee jumper is not in equilibrium at the bottom of the dive before he springs back upwards.

Q: 1. A 80.0-N board 10.0 m long rests on two supports, each 1.00 m from the end of the board. A 300-N…

Q: In a construction site, two vertical cables are supporting a 3.00m steel beam weighing 1500N.…

A: Given: Mg=1500 N T1 =2000N T2 = 3000 N We have to find m and x

Concept explainers

Torque

Torque is the rotational equivalent of linear force in physics and mechanics. Based on the course of study, it is also known as the moment of force, rotational force, or turning effect.

Question

4]
The members of a truss are pin connected at joint O.
Determine the magnitude of F, and its angle 0 for
equilibrium. Set F = 6 kN.
5 kN
70
30
7 kN
11

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

A 40.0kg uniform platform is suspended by two cables, 2.00m apart, where the centre of the platform lies midway between the cables. A 5.00kg paint bucket is placed on the platform, 24.0cm to the right of the right cable. Determine the tension in each cable.
The homogenous 79 kg disk supported by the rope AB rests against a rough vertical wall. Determine the following: 21. Determine the force acting on the cable. Neglect friction. 22. Determine the force acting on the cable. Use coefficient of friction = 0.70
3. A uniform 25 N beam 6 m long is carried by two men A and B, one at each end of the beam. a) If A exerts a force of 20 N, where must a load of 45 N be placed on the beam? b) What force does B exert? complete solution please
One end of a uniform 4.00-m-long rod of weight Fg is supported by a cable at an angle of = 37 with the rod. The other end rests against the wall, where it is held by friction as shown in Figure P12.23. The coefficient of static friction between the wall and the rod is s= 0.500. Determine tile minimum distance x from point A at which an additional object, also with the same weight Fg can be hung without causing the rod to slip at point A.
A uniform 40.0-kg scaffold of length 60 m is supported by tow light cables below. An 80.0 kg painter stands 1.0 m from the left end of the scaffold, and his painting equipment is 1.5 m from the right end. If the tension in the cable is twice that in the right cable, find the cables and mass of the equipment.
Explain the need for tall towers on a suspension bridge to ensure stable equilibrium.
A 20.0-kg horizontal plank 4.00 in long rests on two supports, one at the left end and a second 1.00 m from the right end. What is the magnitude of the force exerted on the plank by the support near the right end? (a) 32.0 N (b) 45.2 N (c) 112 N (d) 131 N (e) 98.2 N
The bones of the forearm (radius and ulna) are hinged to the humerus at the elbow. The biceps muscle connects to the bones of the forearm about 2.15 cm beyond the joint. Assume the forearm has a mass of 2.25 kg and a length of 0.425 m. When the humerus and the biceps are nearly vertical and the forearm is horizontal, if a person wishes to hold an object of mass 6.95 kg so that her forearm remains motionless, what is the force ? exerted by the biceps muscle? ?=
Two identical strings making an angle of ? = 31.3° with respect to the vertical support a block of mass m = 17.2 kg. What is the tension in each of the strings?
In a construction site, two vertical cables are supporting a 3.00m steel beam weighing 1500N. Suppose cable A can support a maximum weight of 2000N while cable B can support a maximum weight of 3000N. A construction worker would like to place an object on the horizontal beam, what is the maximum mass that he can put without breaking the cables? where should the object be located? Illustrate.
In an isometric exercise a person places a hand on a scale and pushes vertically downward, keeping the forearm horizontal. This is possible because the triceps muscle applies an upward force M perpendicular to the arm, as the drawing indicates. The forearm weighs 24.0 N and has a center of gravity as indicated. The scale registers 103 N. Determine the magnitude of M. N
A rigid bar of mass M is supported symmetrically by three wires each of length l. Those at each end are ofcopper and the middle one is of iron. The ratio of their diameter, if each is to have the same tension, is equal to (a)YcopperYiron(b) √YironY copper(c)Yiron2Ycopper2(d)YironYcopper