12. Asphalt at 120 °F, considered to be a Newtonian fluid with a viscosity 80,000 times that of water and a specific gravity of 1.09, flows through a pipe of diameter 2.0 in. If the pressure gradient is 1.6 psi/ft determine the flowrate assuming the pipe is (a) horizon- tal; (b) vertical with flow up.

12. Asphalt at 120 °F, considered to be a Newtonian fluid with a viscosity 80,000 times that of water and a specific gravity of 1.09, flows through a pipe of diameter 2.0 in. If the pressure gradient is 1.6 psi/ft determine the flowrate assuming the pipe is (a) horizon- tal; (b) vertical with flow up.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

the hydraulic radius of a pipe with a diameter of 12mm is
The flow carried by pipe below discharges into the open atmosphere. If the pipe length is 300 m, diameter is 150 mm and roughness of 0.0025 mm, write the equation(s) required to determine the maximum discharge.
true or false 1. In open channels of constant slope and constant cross section, the liquid accelerates until the head loss due to frictional effects equals the elevation drop. 2. The consumes electrical energy is greater than or equal to the flow energy that it delivers 3. The Hydraulic Radius for an Open Channel Flow with fluid flowing fully in a circular section, is equal to r/2.
1 - If the pipeline is now specified to be of Schedule 40 with a nominal diameter of 6 in., and the available pressure at the pump exit is P2 = 132.7 psig, what flow rate Q (gpm) can be expected? Answer the following additional questions: 2 -If the combination of pump and motor is 80% efficient, how much electrical power (kW) is needed to drive the pump? 3 -, in order to avoid vapour lock, the pressure in the pipeline must always be above the vapor pressure of the crude oil, what is the maximum permissible elevation of point 3 relative to point 4? 4 -If the flow in the pipeline were at the upper limit of being laminar, what pump exit pressure would then be needed? (Answer this part without using the friction factor plot.
Please help correct the attached part using the information given:Water flows at a rate of 2.4f * t ^ 3 / s in an old, rusty 7.8-in.-diameter pipe that has a relative roughness of 0.010. It is proposed that by inserting a smooth plastic liner with an inside diameter of 7.0 in. into the old pipe as shown in the Figure the pressure drop per mile can be reduced. Is it true that the lined pipe can carry the required 2.4f * t ^ 3 / s at a lower pressure drop than in the old pipe? Support your answer with appropriate calculations.
Q1/ Neglecting losses, determine the discharge in Fig. below Oil sp gr 0.75 3 ft 4 in, diam Water
Q1/ Neglecting losses, determine the discharge in Fig. below Oil sp gr 0.75 3 ft 4 ft 4 in, diam Water
Water at 38°C flows from A to B through 244 m of average 300-mm-I.D. cast iron pipe (e = 0.00061 m).Point B is 9.1 m above A, and the pressure at B must be maintained at 138 kPa. If 0.222 m3/s is to flowthrough the pipe, what must be the pressure at A? Ans. 314 kPa (show the complete solution with diagram) [Note: Indicate the formula used in determining the friction factor. (Colebrook Equation, Haaland Equation, andor Swamee Jain Equation). If not given, Use properties of fluid based ontemperature available ontheinternet.E.g. (density, viscosity). Apply roughness of pipe values from https://www.pipeflow.com/pipe-pressure-drop-calculations/pipe-roughness]
Two pipes with C1= 120, connected in series, discharge 4.75 cfs with a loss of head of 27 ft. Each pipe has a length of 1000 ft.If one pipe has a diameter of 18 inches, determine the diameter of the other pipe. Neglect minor losses.
For the Pipe shown Q=4250 gallons per minute (gpm), P1=132 kPa and P2 = 211 kPa. If the pipe carries a special fluid of SG=1.2, determine the total head lost.
A 5 cm diameter potable water line is to be run through a maintenance room in a commercial building. Three possible layouts for the galvanized iron water line are proposed as shown in the figure. The bends are conventional threaded fittings. Select the option that minimizes losses and determine the pressure drop for a flow of 350 L/min. For the elbo losses use, hℓm =
The 800-mile-long Trans-Alaska pipeline is designed to carry 4.4×10 7 gallons per day of crude oil (SG = 0.86, kinematic viscosity = 4.95×10 −5 ). The 4-ft-dia pipe is made of galvanized iron. Determine the total pressure drop in psi over the length of the pipeline. If there are nine equally spaced pumps, estimate the horse power each pump must deliver to compensate the pressure loss.