14) Fill in Questions What are the main components of a feedback control system? What is the purpose of the sensor? Give three important properties of a good sensor. What is the purpose of the actuator? Give three important properties of a good actuator. What is the purpose of the controller? Give the input(s) and output(s) of the controller. What physical variable is measured by a tachometer?

14) Fill in Questions What are the main components of a feedback control system? What is the purpose of the sensor? Give three important properties of a good sensor. What is the purpose of the actuator? Give three important properties of a good actuator. What is the purpose of the controller? Give the input(s) and output(s) of the controller. What physical variable is measured by a tachometer?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter58: Programmable And Motion Control

Section: Chapter Questions

Problem 1SQ

See similar textbooks

Similar questions

Would it be b,d, and c? 2. Which of the following are characteristics of a closed loop control systems? Select allthat apply.a) Low sensitivity to changes in system parametersb) Higher accuracyc) Good regulation against disturbancesd) Reliabilityd) Slower response to inputs.
The background readgin ( if you needed) is on the screenshot Determine the closed loop transfer function from the speed reference, r, to the angular motor speed output, ω, i.e., Y(s)/R(s). Determine kp and ki in terms of the closed-loop natural frequency, ωn, damping ratio, ζ, motor time constant, τ, and motor gain constant, K. Based on your results from (1) and (2), how would large values of the controller gains, kp and ki, affect the closed-loop undamped natural frequency of the system? Explain how bsp can be used to adjust the speed and overshoot of the response to reference values. (Hint: When answering this question, explain how the value of bsp affects the locations of the closed-loop zeros and/or poles.)
Which option is correct and why? 2. Which of the following are characteristics of a closed loop control systems? Select allthat apply.a) Low sensitivity to changes in system parametersb) Higher accuracyc) Good regulation against disturbancesd) Reliabilityd) Slower response to inputs.
For the P-only control , briefly explain changes in controller gain and offset (steady-state error) when PB (Proportional Band) (i) increases (ii) decreases
3. What is the effect of adding a zero to the root locus? And a pole? 4. What does the compensation consist of? 5. When is it introduced into a system? 6. How can we characterize a controller when we design it? Valve
1 a i)Explain the motivations of modern control in the digital world. ii) Explain using the appropriate diagrams, transfer functions and mathematical tools the difference between modern control and classical control systems.
a) Maximum overshoot will be less than 5% and settling time less than 2 secondsDesign the controller accordingly. b)What type of controller is the controller you are designing (P, PI, PD, PID) andWrite down the parameters of this controller according to your calculations. c)Can the controller you designed meet the required values in item a?Please explain.
Explain the use of controllers in Control system. What is proportionalcontroller and with example?
a) If a PI controller or Lag controller is added to a system, briefly explain what is intended in system performance.b) If we consider the application of these two controllers to the system separately, what are the differences between them?c) For a Type 0 system with unit step input, show the output curves that will be obtained when PI and Lag controllers are applied separately on a single graph.
Discuss the influence of sensor and actuator dynamics in system models and the implications for control system design.
A bump test for a self regulating system yields a sensor change of 5.4 volts and a settle time of 52.0 seconds due to an actuator change of 3.1 volts. Calculate the process gain. If a tau ratio of one is selected, calculate the gains for a standard PID controller (Kc,Ti,Td) and the anticipated closed loop settle time for the step change of controller output. (5 answers in total)
Nuclear Instrumentation and Control A proportional controller has a proportional band value of 50%. What is its gain? The controller experiences a 2 volt change at its measurement input. After the controller returns the process to stable operation, what will the controller output voltage be?