16 kN 125 mm 3. The two boards are joined by plywood splices that are fully glued on the surfaces in contact. The length, L = 180 mm, and the clearance between the boards is 6 mm. The ultimate shearing strength of the glue is 2.5 MPa. For the forces applied as shown, determine the factor of safety. Ans: 3.4 %3D 6 mm

16 kN 125 mm 3. The two boards are joined by plywood splices that are fully glued on the surfaces in contact. The length, L = 180 mm, and the clearance between the boards is 6 mm. The ultimate shearing strength of the glue is 2.5 MPa. For the forces applied as shown, determine the factor of safety. Ans: 3.4 %3D 6 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The internal loadings at a critical section along the steel drive shaft of a ship are calculated to be a torque of 2300 lb # ft, a bending moment of 1500 lb # ft, and an axial thrust of 2500 lb. If the yield points for tension and shear are sY = 100 ksi and tY = 50 ksi, respectively, determine the required diameter ofthe shaft using the maximum shear stress theory.
Determine the length of the shortest 7.5mm diameter bronze wire which can be twisted through two and a half complete turns without exceeding a shearing stress of 95MPa. Use G=35GPa.
NEED THE CORRECT ANSWER RIGHT NOW !! THANK YOU IN ADVANCE! The wooden members' A and B are to be joined by plywood splice plates that will be fully glued on the surfaces in contact. The clearance between the ends of the members is to be 13.5 mm, the length of the plywood is L = 356 mm and the width of the wood is W = 113 mm. Find the largest possible value of P (in N) if the average shearing stress in the glue is not to exceed S = 952 kPa. Round off the final answer to three decimal places.
A 20 mm square key with a length of 150 mm was used in a 100 mm shaft to fasten a 250 mm spur gear. Determine the force that will cause the key to shear if the shearing stress is 25 MPa. A.60 kN B. 65 kN C. 70 kN D. 75 kN
A flange coupling has an outside diameter of 200 mm and connects two 40 mm shafts. There are four 16 mm bolts on a 140 mm bolt circle. The radial flange thickness is 20 mm. If the torsional stress in the shaft is not to exceed 26 MPa, determine the shearing stress in the bolts if uniformly distributed. A. 8.5 N/mm2 B. 5.8 N/mm2 C. 6.5 N/mm2 D. 7.5 N/mm2
2) A 200-mm-diameter pulley is prevented from rotating relative to 60-mm-diameter shaft by a 70-mm- long key. If a torque T=2.2kN·m is applied to the shaft, determine the width w if the allowable shearing stress in the key is 60MPa.
The rigid beam BCD is attached by bolts to a control rod at B, to a hydraulic cylinder at C, and to a fixed support at D. The diameters of the bolts used are: dB = dD = 3/8 in., dC =1/2 in. Each bolt acts in double shear and is made from a steel for which the ultimate shearing stress is τU = 40 ksi. The control rod AB has a diameter dA=7/16 in. and is made of a steel for which the ultimate tensile stress is σU = 60 ksi. If the minimum factor of safety is to be 3.0 for the entire unit, determine the largest upward force that may be applied by the hydraulic cylinder at C.
The cylinder of a hydraulic press is made up of thick-walled cylinder having an inside diameter of 300 mm. It is subjected to an internal pressure of 40 MPa Determine the thickness of the cylinder without exceeding a shearing stress of 80 MPa. A. 109.81 mm C. 95.56 mm B. 75 mm D. 120.71 mm
S2) The allowable shear stress limit value of the steel from which the stepped shaft is manufactured is 8MPA talow. If the rounding radius at cross-sectional transitions is r2.25 mm, determine the maximum torque T that can be applied.
For the connection shown, the bolt diameter is d = 30 mm. The average shear stress in the bolts must be limited to 160 MPa. Determine the maximum load P that may be applied to the connection based on the shear strength of the bolts.
Determine the maximum shearing stress in MPa of a helical spring composed of 20 turns and 19 mm wire diameter on a mean radius of 75 mm when the spring is supporting a load of 1000 N, assume the modulus of rigidity of 83 GPa.
The solid rod AB has a diameter dAB5 60 mm and is made of a steel for which the allowable shearing stress is 85 MPa. The pipe CD, which has an outer diameter of 90 mm and a wall thickness of 6 mm, is made of an aluminum for which the allowable shearing stress is 54 MPa. Determine the largest torque T that can be applied at A