Problem 519The Weber number is a dimensionless parameter relating inertial and surface tension forcesin a fluid flow. Consider a droplet of water where the Weber number is defined as:Calculate the Weber number We.pV?dWe =Type your answer..The following parameter values are measured and determined with 95% confidence:p = 1.000 + 0.008cm3V = 5.0 + 0.1d = 1.000 + 0.025 mm (milimeters)m20o = 0.072 + 3%Calculate the absolute uncertainty in the Weber number UweType your answer...

Write the given formula for the Weber number. We=ρV2dσ Here, We is the Weber number, V is the…

19 The Weber number is a dimensionless parameter relating inertial and surface tension forces in a fluid flow, Consider a droplet of water where the Weber number is defined as: Calculate the Weber number We. pV²d We = Type your answer.. The following parameter values are measured and determined with 95% confidence: p = 1.000 + 0.008 V = 5.0 + 0.1 d = 1.000 + 0.025 mm (milimeters) 20 o = 0.072 + 3% Calculate the absolute uncertainty in the Weber number Uwe

19 The Weber number is a dimensionless parameter relating inertial and surface tension forces in a fluid flow, Consider a droplet of water where the Weber number is defined as: Calculate the Weber number We. pV²d We = Type your answer.. The following parameter values are measured and determined with 95% confidence: p = 1.000 + 0.008 V = 5.0 + 0.1 d = 1.000 + 0.025 mm (milimeters) 20 o = 0.072 + 3% Calculate the absolute uncertainty in the Weber number Uwe

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.8P

See similar textbooks

Similar questions

5.13 The torque due to the frictional resistance of the oil film between a rotating shaft and its bearing is found to be dependent on the force F normal to the shaft, the speed of rotation N of the shaft, the dynamic viscosity of the oil, and the shaft diameter D. Establish a correlation among these variables by using dimensional analysis.
When a sphere falls freely through a homogeneous fluid, it reaches a terminal velocity at which the weight of the sphere is balanced by the buoyant force and the frictional resistance of the fluid. Make a dimensional analysis of this problem and indicate how experimental data for this problem could be correlated. Neglect compressibility effects and the influence of surface roughness.
A study of the physical characteristic of honey was conducted due to thelarge demand of royal jelly. A capillary tube viscometer was used by aresearcher in determining the viscosity of the honey. The viscometer is250 mm long with an outside diameter of 55mm and effective thickness of2.5mm and was used horizontally so that the effect of gravity wasneglected. At an ambient temperature of 30oC the following data werecollected: ΔP (Pa) Q (cc/s)10.0 1.2512.5 1.5515 1.8017.5 2.0520.0 2.55 What will be the stress produced per unit length in the tube used in theproduction of royal jelly if it has a radius of 5mm and a flow of 1 capsuleper second. (1 capsule = 0.85 cc of royal jelly).
Measurements at a certain point of a pipe have been done where the following parameters were recorded: Fluid of density = 887 kg/m3, Fluid velocity = 4 m/s, Pressure= 11.3 KN/m2 If the total energy per unit weight at this point = 32 m, then the potential energy is:
In the gap between the two plates, the lubricant flows in one direction (x) by the pressure gradient. Lubricants are incompressible Newtonian fluids, flows are laminates, and terminal effects are ignored. Find the maximum flow rate [m/s] when the pressure difference (△P/L) per unit length is 25000 Pa/m.Data: clearance between plates (B) = 6 mm, lubricant viscosity (μ) = 25 cP (1cP = 10-3 Pa·s), lubricant density (=) = 0.88 g/cm3
In the gap between the two plates, the lubricant flows in one direction (x) by the pressure gradient. Lubricants are incompressible Newtonian fluids, flows are laminates, and terminal effects are ignored. Find the maximum flow rate [m/s] when the pressure difference (△P/L) per unit length is 25000 Pa/m.Data: clearance between plates (B) = 6 mm, lubricant viscosity (μ) = 25 cP (1cP = 10-3 Pa·s), lubricant density (=) = 0.88 g/cm3 Please.. explain more easy
A small wind turbine is tested in a wind tunnel using the following model parameters: ρ = 1.2 kg/m3 , µ = 1.81x10-5 Ns/m2 , v = 12 m/s, A = 0.03 m2 and Cp is measured as 0.42. Assuming dynamic similarity exists, calculate the power output of a full-size turbine of diameter 60 m operating in air of density 1.3 kg/m3 and viscosity µ = 1.73x10-5 Ns/m2 with wind speeds of 15 m/s
Q.10. To predict the drag on an aircraft at a flight speed of 150 m/s, where the condition of air is such that the local speed of sound is 310 m/s, a pressurized low temperature tunnel is used. Density, viscosity and local sonic velocity at tunnel condition are 7.5 kg/m³, 1.22 x 10-5 Ns/m² and 290 m/s. Determine the flow velocity and the scale of the model. Assume full dynamic similarity should be maintained. Density and viscosity at the operating conditions are 1.2 kg/m³ and 1.8 x 10 Ns/m².
The power P required to drive a propeller is known to depend on the diameter of the propeller D, the density of fluid ρ, the speed of sound a, the angular velocity of the propeller ω, the freestream velocity V , and the viscosity of the fluid µ. (a) How many dimensionless groups characterize this problem? (b) If the effects of viscosity are neglected, and if the speed of sound is not an important variable, express the relationship between power and the other variables in nondimensional form. (c) A one-half scale model of a propeller is built, and it uses Pm horsepower when running at a speed ωm. If the full-scale propeller in the same fluid runs at ωm/2, what is its power consumption in terms of Pm if the functional dependence found in part (b) holds? What freestream velocity should be used for the model test?
A dam 65 ft wide with a nominal flow rate of 260 ft3/s is to be studied with a scale model 3 ft wide using Froude scaling. Froude scaling alone can be used for the given test, whereas Reynolds number and Weber number effects can be neglected. True or False?
Volumetric flow rate, Q, of a pump is a function of impeller diameter d, fluid velocity V,pressure difference P, fluid density  and viscosity .a) (15P) Determine dimensionless  groups.b) (20P) A test is to be performed for a large pump that delivers 1.5 m3/s of water from 40 cmdiameter impeller with pressure rise of 400 kPa. For the test, a model with an 8 cm diameter impelleris to be used. What flow rate should be used and what would be the pressure rise in model pump
An important parameter in certain types of fluid flow problems when a free surface is present is the Froude number (Fr), which can be expressed in equation form as (Fr) = [pv^2/Lw]^1/2 where p is the density of the fluid, v is a velocity, L is a length, and w is the specific weight of the fluid. Show that the Froude number is dimensionless