3.a. An equipotential bonding grid at a farm location is to be connected to the ground terminal bus of the nearest panelboard. Which of the following is the minimum size of solid copper conductor that can be used for this bonding action? A. AWG 8 B. AWG 14 C. AWG 10 D. AWG 12 3.b. Which of the following must be installed in livestock areas per 547.10(A) in the National Electrical Code? A. Equipotential plane B. Surge arrester C. Site-isolating device D. Strike termination device

3.a. An equipotential bonding grid at a farm location is to be connected to the ground terminal bus of the nearest panelboard. Which of the following is the minimum size of solid copper conductor that can be used for this bonding action? A. AWG 8 B. AWG 14 C. AWG 10 D. AWG 12 3.b. Which of the following must be installed in livestock areas per 547.10(A) in the National Electrical Code? A. Equipotential plane B. Surge arrester C. Site-isolating device D. Strike termination device

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.24P

See similar textbooks

Similar questions

What is the minimum-size supply-side bonding jumper required if installed on the line side of a 300-ampere service disconnecting means if the service conductors are sized at 400-kcmil copper? a) 3 AWG copper b) 2 AWG copper c) 1/0 AWG copper d) Parallel 2 AWG copper conductors
D.1-. Which of the following names is commonly used for armored cable on commercial and industrial jobsites?A. RomexB. BXC. ECGD. MCD.2. Which of the following is the most common type of conductor termination used in commercial andindustrial wiring applications?A. A pressure connectionB. A wire nutC. A wire spliceD. A crimped connection D.3. Which of the following terms correctly describes a ventilated metal enclosure that supports powerdistribution conductors of up to 8000 A and 69 kV, and that allows for proper phase arrangement of theconductors?A. A trolley busB. A channel racewayC. A cablebusD. A feeder bus
An overhead transmission line has a span of 250 m and the weight of the line conductor is 0.68 kg per metre. Also the maximum allowable tension in the line is 1510 kg. Calculate the maximum sag and calculate the height above ground at which the conductor should be supported. Assume ground clearance required is 10 metre.
A three-phase, three wire, CBA system with a line voltage of 120 Volt, has three impedances of 30 /60ᴼ in Deltaconnection. Assume that VCA is the reference vector. Determine the line current and draw the voltage-currentphasor diagram.
"A 75-ohm load terminates a 50-ohm transmission line. The point of reflection is at the load. If the measured incident voltage at the point of reflection is 10 Vrms, what is the total voltage at the load? Enter only the numerical value. No need for the unit. Use four decimal places (if the answer is not an integer)."
2.1 Determine the value of the slope of CTAT.Answer:
4.a. An intersystem bonding termination will typically be used as a ground junction for a/anA. patient care area.B. communications system installation.C. fire protection system.D. information technology room.4.b. The supply systems for sensitive electronic equipment are _______ systems.A. four-wire, three-phaseB. three-wire, single-phaseC. three-wire, three-phaseD. four-wire, single-phase
Give the raceway size required for each of the following conductor combinations: 1. Three, 1/0 AWG, Type THHN in EMT
Discus the merits and demerits of SSB over DSB system of transmission.
20. If a cable assembly such as a metal-clad (MC) cable includes an equipment grounding conductor (EGC) for safety and an isolated EGC for performance purposes, insulated conductors will generally have insulation colored green and A. white with orange stripes. B. red with gray stripes.C. green with orange stripes. D. green with yellow stripes.
The Voltage Regulation of a Transmission Line should be _____? A. very high percentage. B. more than 100%. C. zero or nil D. as low as possible.
Give four challenges and suggest solutions for those challenges in wireline operations.