2. How will you be able to tell that your liquid sample is completely vaporized? How long will it approximately take for the sample to vaporize? 3. Given that 0.740 grams of unknown volatile liquid condensed into the 125-mL flask at 0.982 atm pressure and at 372 K temperature, what is the MW (molecular weight) of the unknown volatile liquid?

2. How will you be able to tell that your liquid sample is completely vaporized? How long will it approximately take for the sample to vaporize? 3. Given that 0.740 grams of unknown volatile liquid condensed into the 125-mL flask at 0.982 atm pressure and at 372 K temperature, what is the MW (molecular weight) of the unknown volatile liquid?

Introductory Chemistry For Today

8th Edition

ISBN:9781285644561

Author:Seager

Publisher:Seager

Chapter6: The States Of Matter

Section: Chapter Questions

Problem 6.9E

See similar textbooks

Similar questions

Name two characteristic physical properties that distinguish condensed from gas phases, and one which distinguishes solid from liquid phases. Discuss the differences for each property. Name one colligative property and by an equation (label all variables) and 1-2 sentences the physical meaning. Consider a balloon. What thermodynamic system does it represent? How does this system interact with the environment? Calculate the heat capacity at constant pressure of methane for all its contribution and the total value according to the equipartition theorem. What is a more realistic value at room temperature? Why?
The molar mass of a liquid is determined by the Dumas Method. How is the calculated molar mass of the liquid affected, too high, too low or unaffected, if the student did not heat the volatile liquid at a constant temperature for 5 minutes?
Virial equation can be written in Z (compressibility factor form): Z = pV/RT = 1 + B'p + C'p2 + D'p3 + ... Z = 1 + (B/V) + (C/V2) + (D/V3) + ... Show that C'=(C-B2)/(RT)2 on each Z (compressibility factor form) above.
1) help me please.. need it BEFORE 7:20 pm. THANK YOU SO MUCH! <3 Differentiate solid density versus particle density. Explain the 2nd law of thermodynamics. Explain how water boils faster at the top of the mountain compared at sea level. Use diagram if necessary Explain the difference/similarity of subcooled liquid against/with compressed liquid. Limit answer to 5 sentences.
Computers are not supposed to be in very warm rooms. The highest temperature tolerated for maximum performance is 308 K. Express this temperature in C and F.
A thermally insulated container (closed system) is dropped from a certain height andfilled with water so that it collides inelastically against the ground. what should be the valueof the height in m so that the temperature of the water increases by 0.5 °C? Suppose thatall the energy lost in the fall is invested in increasing the temperature of the water.I considered a gravitational acceleration of 9.81 m/s2.
Show complete solutions and enclose all final answers in a box. Round off final answers to 4 decimal places and use floating values for intermediate answers. A gas column is separated into two segments by a non-permeable partition. On the first segment is 1.63 moles of Helium with volume V1 and on the second segment is 3.84 moles of Oxygen gas with volume V2. Consider both gases to be ideal and at the same pressure P and temperature T. If the partition is removed, calculate the change in entropy of the gaseous system.
Molecules in a gas are being pumped through a vacuum system. Eventually the pressure drops low enough that the gas molecules collide with the chamber walls more than they do themselves. How can the pressure be further reduced? I. Add a secondary pump with a large inlet to capture as many randomly moving molecules as possible. II. Add a secondary pump and insure that once molecules enter it that they can't escape out the inlet.
A hot-air balloon achieves its buoyant lift by heating the airinside the balloon, which makes it less dense than the air outside.Suppose the volume of a balloon is 1800 m3 and therequired lift is 2700 N (rough estimate of the weight of theequiptment and passenger). Calculate the temperature of the airinside the balloon which will produce the required lift. Assumethat the outside air temperature is 0 degrees C and that the air isan ideal gas under these conditions.How do I go about applying the ideal gas law to a problem like thiswhich asks me to factor in buoyant lift?Thanks!
What is w when 1.83 kg of H20(1), initially at 25.0 °C, is converted into water vapour at 185 °C against a constant external pressure of 1.00 atm? Assume that the vapour behaves ideally and that the density of liquid water is 1.00 g/ml (Remember to include a+or-sign as appropriate.) Enter your answer in acceptable SI units, accurate to 3. significant figures. Use an acceptable Sl symbol for units.
The term “airbag” itself is misleading since there’s no significant “air” in these cushions. They are, instead, shaped and vented nylon-fabric pillows that fill, when deployed, with nitrogen gas. They are designed to supplement seatbelt restraints and help distribute the load exerted on a human body during an accident to minimize the deceleration rate and likelihood of injury. But while “supplement the seatbelt” is the mission of airbags, federal regulations require that they be tested and made effective for unbelted occupants, vastly complicating their task. Airbags must do their work quickly because the window of opportunity—the time between a car’s collision with an object and an occupant’s impact on the steering wheel or instrument panel—lasts only milliseconds. For illustration’s sake, imagine a Corvette hitting a bridge abutment head-on at 30 mph. The clock starts the instant the tip of the car’s nose hits the concrete. The Mechanics There are six main parts of an airbag system:…
When you determined the MW of a volatile liiquiid using the Erlenmeyer flask with the aluminum foil cap & the pinhole, explain briefly how you were able to obtain: -Mass of the vapor - Volume of the vapor -Pressure of the vapor - temperature of the vapor B) Calculate the MW of iodethane, a volatile liquid, given the following data obtained from the experiment in 12A, given that PV=nRT (R= 0.0821 L.atm.mol-1.K-1) Mass of residual liquid = 1.6384 g Pressure = 745.6 torr Volume of vapor = 327.8 mL Temp. of vapor = 100.0 C