2. In Figure, the battery voltage is V = 65 volts, and the values of the resistances, in ohms, are 38, 17, and 27, as shown. Find: (a) Total resistance seen by the battery, (b) Current measured by the ammeters shown in the figure, (c) Power output of the battery, (d) Power input to each resistor. V= 65 V 38 Q 172 272

2. In Figure, the battery voltage is V = 65 volts, and the values of the resistances, in ohms, are 38, 17, and 27, as shown. Find: (a) Total resistance seen by the battery, (b) Current measured by the ammeters shown in the figure, (c) Power output of the battery, (d) Power input to each resistor. V= 65 V 38 Q 172 272

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

4) This MCQ QUESTION FROM BASIC POWER ELECTRICAL ENGINEERING course. just write for me the the correct answer.
h. What is the dc power dissipated by the device at the operating point?i. What is the power supplied by VCC ?j. Determine the power dissipated by the resistive elements by taking the difference betweenthe results of parts (h) and (i).
Give a brief introduction about the topic of generation and measurement of direct current voltage...(if possible for 2 pg or 1 pg) high voltage engineering subject..
Solve the following Numerical problems a. What is the Output Voltage of a battery that expends 7.2J of energy in moving 1C of charge? b. A 50-ohm load dissipates 200W of power. How much is the voltage and current across the load? c. If one branch of a 120-V power line is protected by a fuse of 20-A. Will the fuse carry 10-Ohm load? d. If total resistance of a series circuit is 280-Ohm. If one of the resistance is 160-Ohm. What is the sum of other two resistances?
(i) With neat sketch explain the cross sectional view and I-V characteristics of the device which is having uncontrolled turn ON and turn OFF withstanding capability. (ii) Write FOUR application of the above mentioned power semiconductor device.
In the figure, the ideal batteries have emfs ℰ1 = 25.0 V and ℰ2 = 0.500ℰ1, and the resistances are each 2.14 Ω. (a) What is the current in resistor 2? ______________A(b) What is the current in resistor 3? ______________A (please show the units when working through the problem so that I can follow it easier)
Question 1 Consider the adjacent circuit diagram of three different rectifier topologies connected to an 373 Volt three-phase AC system. Assume a load resistance of 36Ω in ALL instances with NO losses in the rest of the circuit. Observe the connections to the AC supply and determine the parameters for, Rectifier C: 1.1) the maximum voltage across the load and the dc load voltage and the r.m.s. load voltage. 1.2) the rectification efficiency and the r.m.s. current rating of the diodes. 1.3) the conduction period of a single diode and the PIV rating of the diodes.
Q2: For the single phase full wave semi controlled rectifier shown: 1-Draw the v-i waveforms for the circuit vm 2-Prove that: lav =~ (1+cos @) 3-Maximum voltage across the load if the AC supply voltage is 208V .
q25/a Write the features of Air circuit breaker and mention its application.
Question 1 Consider the adjacent circuit diagram of three different rectifier topologies connected to an 373 Volt three-phase AC system. Assume a load resistance of 36Ω in ALL instances with NO losses in the rest of the circuit. Observe the connections to the AC supply and determine the parameters for, Rectifier B: 1.1) the maximum voltage across the load and the dc load voltage and the r.m.s. load voltage. 1.2) the rectification efficiency and the r.m.s. current rating of the diodes. 1.3) the conduction period of a single diode and the PIV rating of the diodes.
- single phase half wave uncontrolled rectifier using resistive load 10 ohmand the voltage source is 120 V AC find1- maximum load current2-averge load voltage3-average load current4-RMS load current5-load power6- Power factor7-PIV
Determine V0, I1, ID1, and ID2 for the configuration shown in the figure. With a voltage source (E) equal to 12 volts.