2. Two gaseous streams enter a combined tube in a steady flow manner and leave as a single mixture Gas A at Tube A A= 400 cm² V= 150 m/s V=0.6 m³/kg Data at exit: V= 100 m/s v=0.55 m³/kg Find the following: a. Speed of gas at tube B b. Mass flow rate at exitp Gas B at Tube B A= 250 cm² m= 455kg/min p= 2kg/m³.

2. Two gaseous streams enter a combined tube in a steady flow manner and leave as a single mixture Gas A at Tube A A= 400 cm² V= 150 m/s V=0.6 m³/kg Data at exit: V= 100 m/s v=0.55 m³/kg Find the following: a. Speed of gas at tube B b. Mass flow rate at exitp Gas B at Tube B A= 250 cm² m= 455kg/min p= 2kg/m³.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At a particular stage of a reaction turbine the mean blade speed is 140 m/sec and the steam is at a pressure of 20 bar with temperature of 250° C. Fixed and moving blades at this stage have inlet angles 30° and exit angles 20°. The stage efficiency is 80%. Determine (1) Specific entholpy drop across the stage in kJ/kg. (i) Drum Dia and blade height if heigh is one-twelfth of the drum dia. and the steam flow is 120 kg/sec. (ii) The percentage increase in the relative velocity across the bladings as a result of pressure drop across the blading.
At a particular stage of a reaction turbine the mean blade speed is 140 m/sec and the steam is at a pressure of 20 bar with temperature of 250° C. Fixed and moving blades at this stage have inlet angles 30° and exit angles 20°. The stage efficiency is 80%. Determine (1) Specific entholpy drop across the stage in kJ/kg.
The refrigerant R134a is passing through the diffuser with the inlet diameter of D1=1 inch; p1=150psi; and V1=1000 ft/s as a saturated vapor. The exit parameters are p2=400 psi, and velocity V2=0.5 ft/s. Heat transfer, Work, and Potential energy changes can be neglected. NOTE: Use English units. For the kinetic energy change do not forget dividing to (778*32.2) conversion factor to obtain Btu/lbm. From NIST tables use BTU/lbm units for the enthalpy. Determine: a.Exit temperature in F; b.Mass flow rate in lbm/s; c.Exit diameter D2 in inches. d.Determine exit temperature.
The refrigerant R134a is passing through the diffuser with the inlet diameter of D1=1 inch; p1=150psi; and V1=1000 ft/s as a saturated vapor. The exit parameters are p2=400 psi, and velocity V2=0.5 ft/s. Heat transfer, Work, and Potential energy changes can be neglected. NOTE: Use English units. For the kinetic energy change do not forget dividing to (778*32.2) conversion factor to obtain Btu/lbm. From NIST tables use BTU/lbm units for the enthalpy. Determine: a.Exit temperature in F; b.Mass flow rate in lbm/s; c.Exit diameter D2 in inches. d.Determine exit temperature. show and expalin each step please
The properties of the air in the inlet section with A1 = 0.2562 m2 in a converging-diverging channel are given as U1 = 256,2 m/s, T1 = 362 K, P1 = 136,2 kPa (absolute). Find the required cross-sectional area, pressure, temperature, velocity and mass flow rate to obtain sonic (Ma2=1.0) flow at the outlet. Calculate critical values of A*, U*, T*, P*. Solve the problem by making the necessary assumptions and drawing the schematic figure.
Provide the solution and diagram. Air enters the tower at the rate of 60 kg/s. The entrance enthalpy is 86 KJ/kg and exit enthalpy of 53 KJ/kg. Find the temperature range of the tower if mass flow rate of water is 30 kg/s. A. 14.34 oC B. 16.34 oC C. 10.23 oC D. 15.76oC
Air enters through a duct of a fan with a velocity of 4m/s and an inlet pressure of2cm of water less than atmospheric pressure. The air leaves the fan through aduct at a velocity of 12m/s and a discharge static pressure of 8cm of waterabove atmospheric pressure. If the specific weight of air is 1.2kg/m3 and the fandelivers1 2m3/s, what is the fan input power to the motor if the fan has amechanical efficiency of 70% and motor efficiency of 80%.
Q . It is proposed to pump 8,000 kg/h of toluene at 114 oC and 1.1 atm abs pressure from the reboilerof a distillation tower to a second distillation unit without cooling the toluene before it enters thepump. If the friction loss in the line between the reboiler and pump is 7 kN/m2 and the density oftoluene is 866 kg/m3 . How far above the pump must the liquid level in the reboiler be maintained togive a net positive suction head of 3.5 m? Calculate the power required to drive the pump if the pumpis to elevate the toluene 10 m. The pressure in the second unit is atmospheric and the friction loss inthe discharge line is 35 kN/m2 . The velocity in the pump discharge line is 4 m/s.
QUICKLY AND CORRECTLY PLEASE Steam with enthalpy of 3350 kJ/kg enters a nozzle at a velocity of 80 m/sec. Find the velocity of the steam at the exit of the nozzle if its enthalpy is reduced to 3200 kJ/kg, assuming the nozzle is horizontal and disregarding heat losses.
Water is entering a tank with diameter dt with a constant mass flow rate of ˙m. The tank has an opening at the bottom with diameter do. Assume the exit velocity is √2gh. If the tank is empty, determine:a) The maximum height the water can reach in the tank;b) A relation for the water height, z, as a function of time;c) The time it takes for the tank to reach steady-state.
A reaction turbine has mean blade speed of 220 m/s and blade speed to steam velocity ratio of 0.7. Determine the angle at inlet of blade and work done per kg of steam flow if angle at exit is 20°.
A convergent - divergent nozzle receives wet steam of 2% wet at a pressure of 26 bar with an approach velocity of 100m/ S and expands it to a back pressure of 0.3 bar. Nozzle efficiency is 85% and all the frictional losses take place in the divergent portion only. Determine: (a) The critical throat pressure (b) The discharge of steam (c) The area of cross section of the nozzle at its exit.