(b)For the Zener diode configuration given in Figure Q2(b),i determine the minimum value of R, and I, that will result in VRI, being maintainedat 8 V.ii. calculate the maximum value of R1 based on the given maximum zener current,IzM, so that the zener can operate in safe range.5 kQIzV = 8 VIzM =1 mAVi= 20 VRLFigure Q2(b)

Given : VZ = 8V Izmax = 1 mA. RL is variable Vi = 20 V We need to calculate the value…

(6) For the Zener diode configuration given in Figure Q2(6), i determine the minimum value of R and It that will result in Vg being maintained at 8 V. i. calculate the maximum value of Rz based on the given maximum zener current, IzM, so that the zener can operate in safe range. 5 kQ V;=20 V V,= 8 V Izı=1 mA Figure Q2(b)

(6) For the Zener diode configuration given in Figure Q2(6), i determine the minimum value of R and It that will result in Vg being maintained at 8 V. i. calculate the maximum value of Rz based on the given maximum zener current, IzM, so that the zener can operate in safe range. 5 kQ V;=20 V V,= 8 V Izı=1 mA Figure Q2(b)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
In a 1-phase full wave bridge rectifier with Vs = Vm sin ωt, with R load & ideal diodes. The expression for the average value of the output voltage is 2Vm/π Select one: True False
Q1: In this Zener diode regulator, the source voltage varies from 6 V to 14 V. Assume that the load current varies between 1 mA and 35 mA, and that the diode is an ideal 4 V Zener diode. What is the largest allowable resistance that will ensure the load voltage remains constant with variations in load current and source voltage? Please enter your answer to 3 significant figures. Q2: Given the circuit design for a Zener diode regulator in the Ques 1, what is the maximum power that will be dissipated by the Rs resistor? You are told that the source voltage Vs varies from 6 V to 11 V, the load current il varies between 2 mA and 45 mA, and the diode is an ideal 3 V Zener diode. You will need to recalculate the maximum allowable resistance Rs with your new values, as part of this question. Please enter your answer to 3 significant figures, and in Watts.
Electronics What are the similarities and differences between a diode and a silicon controlled rectifier? You may offer illustrations to support the answer.
a. Using standard resistor values, what value of R1 is needed to achieve 1.18V ±0.01V at Vout? b. Using the R1 value chosen in (a) part, what happens to the voltage Vout when a load resistance of 10K is added (between Vout and ground). c. What is the minimum value of load resistance required for correct operation Zener diode is used in place of si diode. Or you can assume zener current according to requirement Answer it i will rate
diode zener a, DESIGN THE NETWORK IN THE FIGURE, TO KEEP, "VL" at 12 V for a variation in load (IL) from 0 to 200 mA, DETERMINE "Rs" and "Vz" b. determine "P2min" for the Zener diode from section a
How is Zener diode connected into a circuit? What determines the voltage at which a Zener diode break down? What considerations go into determining the power dissipation rating of a Zener diode? Draw a label the schematic symbol used to represent a Zener diode What determines the maximum Zener current of a Zener diode? What is the difference between the maximum Zener current and the reverse current for a Zener diode? What does a positive Zener voltage temperature coefficient signify? What does a negative Zener voltage temperature coefficient signify? How can a Zener diode be temperature compensated?
⦁ Consider the below zener diode circuit and find the values of , , , . Use the constant voltage drop model which is shown is Figure 2. Show your solution steps clearly and explain them. The answers without solution steps will not be graded. Also, state your results in the sections below the circuits. ( = 0.1 )
In an electronic laboratory, a diode rectifier tube has a plate resistance of 500 ohms (assumed constant) and is connected as a half – wave rectifier to a load of resistance 1500 ohms. The energizing supply voltage is 460V, 60Hz effective. Determine the average load voltage.
Redraw the circuit and determine the value of ID and VO for the diode configurationshown in Figure Q2a.
Consider the full-wave rectifier circuit shown below, where• vS(t) is a sinusoidal signal with a peak value (Vs = 5 V).• Diodes are modelled using constant voltage model with VDO = 0.7 V• The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hza) Calculate the transformer turns ratio. b) Plot in the same graph signal vS(t) and the output signal vO(t) versus time (t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms value of the output signal vO(t). (hint: sin2(x) = 0.5(1- cos(2x))) d) If a capacitor C=3.58 F is connected across R = 10 k, repeat (b) in a new graph
Determine Q-point for the diodes in the circuit given below using the ideal diode model where, R1 = 12.2 kΩ, R2 = 16 kΩ, and R3 = 14 kΩ. (Note: Label the diodes from left to right.)