2.50. A solution containing hazardous waste is charged into a storage tank and subjected to a chemical treatment that decomposes the waste to harmless products. The concentration of the decomposing waste, C, has been reported to vary with time according to the formula C = 1/(a + bt) When sufficient time has elapsed for the concentration to drop to o.01 g/L, the contents of the tank are discharged appropriately. The following data are taken for C and t: t(h) 1.0 2.0 3.0 4.0 5.0 C(g/L) 1.43 1.02 0.73 0.53 0.38 a. If the given formula is correct, what plot would yield a straight line that would enable you to determine the parameters a and b? b. Estimate a and b using the method of least squares (Appendix A.1) or graphics software. Check the goodness of fit by generating a plot of C versus t that shows both the measured and predicted values of C. c. Using the results of Part (b), estimate the initial concentration of the waste in the tank and the time required for C to reach its discharge level. Answer d. You should have very little confidence in the time estimated in Part (c). Explain why. e. There are potential problems with the whole waste disposal procedure. Suggest several of them. Exploratory Exercise-Research and Discover f. The problem statement includes the phrase "discharged appropriately." Recognizing that what is considered appropriate may change with time, list three different means of disposal and concerns with each.

Introduction to Chemical Engineering Thermodynamics
8th Edition
ISBN:9781259696527
Author:J.M. Smith Termodinamica en ingenieria quimica, Hendrick C Van Ness, Michael Abbott, Mark Swihart
Publisher:J.M. Smith Termodinamica en ingenieria quimica, Hendrick C Van Ness, Michael Abbott, Mark Swihart
Chapter1: Introduction
Section: Chapter Questions
Problem 1.1P
icon
Related questions
Question

The problem that is listed below need to be solved and you may access that problem via viewing them through the attached images in this request. **Question Number #2.50**

2.50. A solution containing hazardous waste is charged into a storage tank and subjected to a chemical treatment that decomposes the waste to harmless products. The concentration of
the decomposing waste, C, has been reported to vary with time according to the formula
C = 1/(a + bt)
When sufficient time has elapsed for the concentration to drop to o.01 g/L, the contents of the tank are discharged appropriately.
The following data are taken for C and t:
t(h)
1.0
2.0 3.0 4.0 5.0
C(g/L) 1.43 1.02 0.73 0.53 0.38
a. If the given formula is correct, what plot would yield a straight line that would enable you to determine the parameters a and b?
b. Estimate a and b using the method of least squares (Appendix A.1) or graphics software. Check the goodness of fit by generating a plot of C versus t that shows both the measured
and predicted values of C.
c. Using the results of Part (b), estimate the initial concentration of the waste in the tank and the time required for C to reach its discharge level.
Answer
d. You should have very little confidence in the time estimated in Part (c). Explain why.
e. There are potential problems with the whole waste disposal procedure. Suggest several of them.
Exploratory Exercise-Research and Discover
f. The problem statement includes the phrase "discharged appropriately." Recognizing that what is considered appropriate may change with time, list three different means of disposal
and concerns with each.
Transcribed Image Text:2.50. A solution containing hazardous waste is charged into a storage tank and subjected to a chemical treatment that decomposes the waste to harmless products. The concentration of the decomposing waste, C, has been reported to vary with time according to the formula C = 1/(a + bt) When sufficient time has elapsed for the concentration to drop to o.01 g/L, the contents of the tank are discharged appropriately. The following data are taken for C and t: t(h) 1.0 2.0 3.0 4.0 5.0 C(g/L) 1.43 1.02 0.73 0.53 0.38 a. If the given formula is correct, what plot would yield a straight line that would enable you to determine the parameters a and b? b. Estimate a and b using the method of least squares (Appendix A.1) or graphics software. Check the goodness of fit by generating a plot of C versus t that shows both the measured and predicted values of C. c. Using the results of Part (b), estimate the initial concentration of the waste in the tank and the time required for C to reach its discharge level. Answer d. You should have very little confidence in the time estimated in Part (c). Explain why. e. There are potential problems with the whole waste disposal procedure. Suggest several of them. Exploratory Exercise-Research and Discover f. The problem statement includes the phrase "discharged appropriately." Recognizing that what is considered appropriate may change with time, list three different means of disposal and concerns with each.
Expert Solution
trending now

Trending now

This is a popular solution!

steps

Step by step

Solved in 6 steps with 6 images

Blurred answer
Knowledge Booster
Mole balances and approximations
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemical-engineering and related others by exploring similar questions and additional content below.
Recommended textbooks for you
Introduction to Chemical Engineering Thermodynami…
Introduction to Chemical Engineering Thermodynami…
Chemical Engineering
ISBN:
9781259696527
Author:
J.M. Smith Termodinamica en ingenieria quimica, Hendrick C Van Ness, Michael Abbott, Mark Swihart
Publisher:
McGraw-Hill Education
Elementary Principles of Chemical Processes, Bind…
Elementary Principles of Chemical Processes, Bind…
Chemical Engineering
ISBN:
9781118431221
Author:
Richard M. Felder, Ronald W. Rousseau, Lisa G. Bullard
Publisher:
WILEY
Elements of Chemical Reaction Engineering (5th Ed…
Elements of Chemical Reaction Engineering (5th Ed…
Chemical Engineering
ISBN:
9780133887518
Author:
H. Scott Fogler
Publisher:
Prentice Hall
Process Dynamics and Control, 4e
Process Dynamics and Control, 4e
Chemical Engineering
ISBN:
9781119285915
Author:
Seborg
Publisher:
WILEY
Industrial Plastics: Theory and Applications
Industrial Plastics: Theory and Applications
Chemical Engineering
ISBN:
9781285061238
Author:
Lokensgard, Erik
Publisher:
Delmar Cengage Learning
Unit Operations of Chemical Engineering
Unit Operations of Chemical Engineering
Chemical Engineering
ISBN:
9780072848236
Author:
Warren McCabe, Julian C. Smith, Peter Harriott
Publisher:
McGraw-Hill Companies, The