3. In the following system, the flow rate of Q= 400 lt / s is transmitted from the A chamber to the B chamber. There is a valve in the pipe where the diameter is large and there is a local loss due to the valve. Using the valve formula (K) as 10 (see formulas), calculate the distance H between the waterface elevations of the two chambers. Draw the relative energy and piezometer lines.

3. In the following system, the flow rate of Q= 400 lt / s is transmitted from the A chamber to the B chamber. There is a valve in the pipe where the diameter is large and there is a local loss due to the valve. Using the valve formula (K) as 10 (see formulas), calculate the distance H between the waterface elevations of the two chambers. Draw the relative energy and piezometer lines.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the system given below, the water taken from the A chamber is transmitted to the D chamber with the help of the pump at the C point. The power of the pump at the C point, the local loss coefficient due to the valve at the B point and other data are given in the table. How many meters (m) is the elevation difference between these two reservoirs? Hopper-Pipe connections are sharp (90⁰ junction). Note: The Colebrook-White equation will be used in the solution. Kinematic viscosity value will be taken as 1.13x10-6 m2 / s. please fast help
The diameter of the pipe at the larger end is 0.50 cm and at the smaller end is 0.20 cm, the larger and smaller ends located 7 meters and 3 meters respectively, from the datum line. If the larger end, the velocity is 1.2 m/s and the pressure is 5200 kN/m2 , compute the velocity at the smaller end.
Draw the right diagram for the problem. Show complete solution. Water at 60 F from a lake through 500 ft if 4in ID cast iron pipe at a water turbine 250 ft below the surface of the lake. After flowing from the turbine, the water is discharged into the atmosphere through a horizontal 50 ft section of the same pipe. The turbine power output is 10hp when the water in the discharged pipe is flowing at 5 ft/s. a. What is the turbine efficiency defined as the actual power output of the turbine divided by the power output that would be withdrawn if there are no friction within the turbine? b. If the turbine were by passed, what would be the flow rate of water through the 500 ft of 4in pipe?
Show the step by step solution. Thank you. 3. A pump draws water from reservoir A and lifts it to reservoir B as shown in Figure 4-10. The loss of head from A to 1 is 3 times the velocity head in the 150-mm pipe and the loss of head from 2 to B is 20 times the velocity head in the 100-mm pipe. Compute the horsepower output of the pump and the pressure heads at 1 and 2 when the discharge is: (a) 12 L/s (b) 36 L/s
Water flows through a reducer in a pipe as shown. The pressure at A is equal to 345 kPa and the pressure at B is equal to 325 kPa. What is the flow rate of the water in the pipeline? Flow 150 mm inside diam. 60 mm inside diam.
A prismatic vessel has two compartments A and B communicating by an orifice 0.3m square with C = 0.60. The horizontal cross –section of A is 10 sqm and that of B is 0.40 sqm. At a certain time, the water in A is 6m above the center of the orifice and in B is 3m. a. Compute the discharge from A to B. b. Find the time in which the water surfaces in the two tanks will reach the same elevation. c. Howsoon thereafter will the water surface be 1m apart?
8. A pumped fluid distribution system is being designed to deliver 400 gal/min of water to a cooling system in a power generation plant. Use the figure below to make an initial selection of Schedule 40 pipe sizes for the suction and discharge lines for the system. Also, solve for the actual average velocity of flow for each pipe. DN (mm) NPS (in) 250 200 150 - 125 - Suction lines 100 - 90 - 3 65 - 2 50 Discharge lines 40 32E 25 E 15 20 200 400 600 800 1000 2000 4000 6000 8000 10000 10 100 Volume Flow Rate, Q (gal/min) 6 8 10 ++++ 15 20 25 30 40 +++++++++ ++++++++++++ 60 80 100 150 200 300 400 500600 800 1000 1200 2000 Volume Flow Rate, Q (m/h)
3. . In a differential pressure flow meter, determine the velocity at the outlet for the given technical specification. The density of the liquid flowing through the pipeline is 997 kg/m³, Pressure at inlet is 10 Ib/ft2, pressure at outlet is 8 Ib/ft2 and cross sectional area of the orifice is 0.2512 m. Note: Ratio of meter diameter to pipe diameter is 0.5 and discharge coefficient is 0.61. Also, find the differential pressure and flow rate.
A washing machine is supplied with hot and cold water from two different supplies. Draw the bock the diagram of a process control that controls the hot water flow Q? and the cold water flow Q? to adjust the water temperature as the machine user specify? and define each block? Note: pressure controlled pneumatic actuator is used as a valve.
QUESTION 4 The figure below shows a fluid flow system that is designed to pump water at 20 °C from a lower vented reservoir to an elevated vented tank. Note that the drawing is not to scale as the dimensions of the reservoirs are very large relative to those of the piping system. The suction line entering the pump is specified as 20 m of 3½" schedule 40 commercial steel pipe; the discharge line from the pump is 180 m of 2%" schedule 40 commercial steel pipe. 15 m 3 m 31/2-in Schedule 40 steel pipe Fully open gate valve 21/2-in Schedule 40 steel pipe Flanged regular 90⁰ elbows Pump Flow Swing-type check valve valve Butterfly (K butterfly = 0.8) a. Starting from the Bernoulli equation (in 'head' form) for the situation where the liquid levels in the two reservoirs are reference points 1 and 2, derive the correct equation for pump head Hpump (m) in terms of volumetric flow rate Q (m³/s) and other process variables (e.g. z, f, L, D, K). b. Using Excel (or another suitable program), create…
:00 Time LeiL HAM YAHIA ZARARIA ALY MOUSTAFA: Attempt 1 15 m 3 6. 6 m 6 m Elbow 6 m 3 m 1 DELL
A pump draws water from reservoir A and lifts it to reservoir B as shown. The head loss from A to 1 is three times the velocity head in the 150-mm diameter pipe and the head loss from 2 to B is twenty-five times the velocity head in the 100-mm diameter pipe. The discharge in the pipe is 20 liters/second. Find the power delivered by the pump in kW. Calculate the pressure head at point 1 in meters. Solve the pressure head at point 2 in meters.