The hydrostatic transmission shown in the figure, is used to move a pulley attached to the shaft of the hydraulic motor. The actual flow rate of the hydraulic pump is 10 gpm, and the actual flow rate of the hydraulic motor is 7.5 gpm. The relief pressure is 2500 psi and the pressure in the inlet port of the hydraulic motor is 1000 psi. Calculate the power loss across the relief valve.

The hydrostatic transmission shown in the figure, is used to move a pulley attached to the shaft of the hydraulic motor. The actual flow rate of the hydraulic pump is 10 gpm, and the actual flow rate of the hydraulic motor is 7.5 gpm. The relief pressure is 2500 psi and the pressure in the inlet port of the hydraulic motor is 1000 psi. Calculate the power loss across the relief valve.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At point A where the diameter at of the pipe is 18 cm the pressure reading is 22.5 cm of Mercury. At point B, 3 m lower than A, the diameter is 48 cm and the pressure reading is 50 cm of Mercury. If the total head loss between the two points is 1.50 m, solve for the discharge. Water is flowing through the pipe. subject: hydraulics
Water recirculates at a volume flow rate of 0.4524 ft3/min from the blade outlet to the impeller, and shaft sealing losses are negligible. A centrifugal pump has a hydraulic efficiency of 95% and a mechanical efficiency of 93%, respectively. Calculate the pump efficiency in percent if the pump delivers water at a flow rate of 12 ft3/min.
The below figure shows a pump that transfers a steady stream of 35◦API crude oil from an oiltanker to a refinery storage tank, both free surfaces being open to the atmosphere. Theeffective length—including fittings—of the commercial steel pipe is 6,000 ft. The dischargeat point 4 is 200 ft above the pump exit, which is level with the free surface of oil in thetanker. However, because of an intervening hill, point 3 is at a higher altitude than point 4.Losses between points 1 and 2 may be ignored.The crude oil has the following properties:Density ρ = 53 lbm/ft 3 ; Viscosity μ = 13.2 cP; Vapour Pressure Pv = 4.0 psia Answer the following questions:1. If the combination of pump and motor is 80% efficient, how much electrical power(kW) is needed to drive the pump?2. If, in order to avoid vapour lock, the pressure in the pipeline must always be above thevapor pressure of the crude oil, what is the maximum permissible elevation of point 3relative to point 4?3. If the flow in the pipeline…
A 6 in. pipe, as shown in the figure, takes water from a reservoir and terminates in a nozzle having a jet diameter of 2 in. Assuming a nozzle loss of 8 percent of the velocity head in the jet, compute the discharge (in S.I. units). Also, make a table showing the elevation head, velocity head, pressure head, and total head at each of the six stations. Lastly, draw the hydraulic gradient line (H.G.L.) & the energy gradient line (E.G.L.).
The impeller of the centrifugal pump is 350 mm diameter, and the width of the blade passages at outlet is 18 mm. A pump, which runs at 16.6 rev/s, is mounted so that its centre is 2.4 m above the water level in the suction sump. It delivers water to a point 19 m above its centre; the friction loss in the suction pipe is 68 Q² meter and that in the delivery pipe is 650 Q² meter where Q in m3/s is the rate of flow. The blades themselves occupy 5% of the circumference and are backward facing at 35° to the tangent. At inlet, the flow is radial and the radial component of velocity remains unchanged through the impeller. Assuming that 50% of the velocity head of the water leaving the impeller is converted to pressure head in the volute, and that friction and shock losses in the pump, the velocity heads in the suction and delivery pipes are negligible, calculate the following:The flow rate, m3/s, of the pump. Manometric efficiency, in %, of the pump.
The impeller of the centrifugal pump is 350 mm diameter, and the width of the blade passages at outlet is 18 mm. A pump, which runs at 16.6 rev/s, is mounted so that its centre is 2.4 m above the water level in the suction sump. It delivers water to a point 19 m above its centre; the friction loss in the suction pipe is 68 Q² meter and that in the delivery pipe is 650 Q² meter where Q in m3/s is the rate of flow. The blades themselves occupy 5% of the circumference and are backward facing at 35° to the tangent. At inlet, the flow is radial and the radial component of velocity remains unchanged through the impeller. Assuming that 50% of the velocity head of the water leaving the impeller is converted to pressure head in the volute, and that friction and shock losses in the pump, the velocity heads in the suction and delivery pipes are negligible, calculate the following: The flow rate, m3/s, of the pump. Manometric efficiency, in %, of the pump.
The figure shows a portion of a fire protection system in which a pump draws water at 60°F(v=1.21 x10-5 m² from a reservoir and delivers it to a point B at the flow rate of 1500 gal/min. Calculate the required height of the the water level in the tank in order to maintain 5.0 Psig pressure at point A
A pump with an efficiency of 89.842 percent delivers water at a rate of 13.79 m3/s but with a leakage loss of 0.5 m3/s. The friction losses within the pump result in a 1 m head loss. What is the total dynamic head of the pump in meters if it has a mechanical efficiency of 98 percent?
Use figure below Question : Water at 20 C is to be pumped through 2300 ft of pipe from reservoir 1 to 2 at a rate of 2.5 ft3/s, as shown in the figure. If the pipe is galvanized iron of diameter 7 in and the pump is 75% efficient, what horsepower pump is needed? Neglect minor losses. HINT : pumped through 2300 ft of pipe from reservoir 1 to 2 at a rate of 2.5 ft3/s, & galvanized iron of diameter 7
The volume flow rate of water that recirculates from the blade outlet to the impeller is estimated to be 0.4524 ft^3/min, and the losses through the shaft sealing is negligible. The hydraulic and mechanical efficiency of a centrifugal pump are 95% and 93%, respectively. If the pump delivers water a flow rate of 12 ft^3/min, calculate the pump efficiency in %.
A vessel is being filled with water through an inlet at section 1 having a diameter of 40 mm and a faucet at section 3. The velocity at section 1 is given as 5 m/s, while the discharge at section 3 is given as 0.012 m^3/ s. Assume constant water level. Use 60 mm for the diameter of the outlet at section 2. A. What is the discharge at section 2? B. What is exit velocity at section 2? C. If the water level varies and the velocity at section 2 is 8m/s find the rate of change when d is equal to 1000mm?
The following system is fed by a centrifugal pump. The piping is constructed from smooth plastic of OD 55 mm, wall thickness 2.5 mm. The minor losses for the system prior to the pump are given by KL = 12.0. The system curves for this pump are attached. If the flowrate is reduced to 1.4 m3/hr, and the upstream head requirement were 17 m, what would the electrical power requirement of the pump be?