3. The three bus-bar conductors in an outdoor sub-station are supplied by units of post insulators. Each unit consists of a stack of 3-pin insulators fixed one on the top of the other. The voltage across the lowest insulator is 8-45 kV and that across the next is 7-25 kV. Find the bus-bar voltage of the station. [38-8 kV]

3. The three bus-bar conductors in an outdoor sub-station are supplied by units of post insulators. Each unit consists of a stack of 3-pin insulators fixed one on the top of the other. The voltage across the lowest insulator is 8-45 kV and that across the next is 7-25 kV. Find the bus-bar voltage of the station. [38-8 kV]

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter10: Using Wire Tables And Determining Conductor Sizes

Section: Chapter Questions

Problem 4PP: 4. Eight 10 AWG aluminum conductors with Type THWN insulation are installed in a single conduit....

See similar textbooks

Similar questions

4. Eight 10 AWG aluminum conductors with Type THWN insulation are installed in a single conduit. What is the maximum current-carrying capacity of these conductors? Assume an ambient temperature of .
What are the colors of the conductors in nonmetallic-sheathed cable for a. 2-wire cable? _______________, _______________ b. 3-wire cable? _______________, _______________, _______________
What is the voltage rating of the conductors in Type NMC cable? _______________
Define service-drop conductors.
1. Which of the following statements about equipment grounding conductors is true?A. Unacceptable equipment grounding conductors include conduit, tubing, and cable armor.B. They must be capable of withstanding the higher level of ground-fault current to perform their safety function.C. They increase voltages above ground potential on conductors and equipment enclosures during normal operation.D. When they're far from their associated circuit conductors, impedance values are kept as low as possible during ground-faultconditions.
What is the rated amps city per phase for six No. 3 THHN copper current-carrying conductors with two conductors per phase (parallel) and all conductors installed in the same conduit
Some electricians do not bother to calculate the minimum size of neutral service conductor. They size the minimum ungrounded conductor size and then use this information to determine the minimum neutral conductor size. Explain how they determine the minimum neutral size using the minimum ungrounded conductor siz
4. What can installation records be used to determine while servicing equipment?A. Broken connectors in a cable linkB. Problems due to aging during operationC. Broken fiberD. Decreased bending radius during operation
On a 120/240 V, single-phase, three-wire system, identify the following: a. Voltage between one grounded conductor and one ungrounded conductor b. Voltage between two ungrounded conductors.
2.a. What's defined as an assembly consisting of a service raceway, guy wires or braces, service head, andany fittings necessary for the termination and support of overhead service conductors?A. Drip loopB. Service lateralC. Service dropD. Service mast 2.b. What's likely to happen when connected parallel conductors are different lengths?A. An NEC violationB. Misidentification of conductor cablesC. An uneven distribution of currentD. Conductor termination
Most residential general lighting circuits are wired with 14-AWG copper conductors and are protected by 15-amp circuit breakers. However, there are many electricians who install 12-AWG copper conductors and protect them with 20-amp circuit breakers. How will you know which conductor size and which circuit breaker size will be used for the general lighting branch circuits in the house you are wiring?
The NEC requires the grounded conductors to be routed to the service disconnecting means enclosure and bonded to that enclosure. For equipment that is identified as suitable for use as service equipment, this is typically accomplished using a(n)________. a) Bonding conductor b) Grounding conductor c) Equipment grounding conductor d) Main bonding jumper