3.109 A bowl is inverted symmetrically and held in a dense fluid, SG = 15.6, to a depth of 200 mm measured along the centerline of the bowl from the bowl rim. The bowl height is 80 mm, and the fluid rises 20 mm inside the bowl. The bowl is 100 mm inside diameter, and it is made from an old clay recipe, SG = 6.1. The volume of the bowl itself is about 0.9 L. What is the force required to hold it in place? AFB F 20 cm D= 10 cm 8 cm 2 cm W

3.109 A bowl is inverted symmetrically and held in a dense fluid, SG = 15.6, to a depth of 200 mm measured along the centerline of the bowl from the bowl rim. The bowl height is 80 mm, and the fluid rises 20 mm inside the bowl. The bowl is 100 mm inside diameter, and it is made from an old clay recipe, SG = 6.1. The volume of the bowl itself is about 0.9 L. What is the force required to hold it in place? AFB F 20 cm D= 10 cm 8 cm 2 cm W

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water at 25° is flowing between A and B through a steel pipe 30 centimeters in diameter and a lengthof 47m. Point B is 10 meters above A and thepressure at B must be maintained at 1.4 kg/cm2. If 220 It/s circulate through the pipe, what pressure must exist in A?
Three types of fluids stack in an open tank as shown in the picture. If the specific gravidties are sg1=1.00, sg2=2.00, sg3=3.00, and h1=1.00 m, h2=1.00 m, h3=1.00 m, calculate the gage pressure at location 4, P4(gage)=_________(kPa)
The 45 ° V-tube in Fig. contains water and is open atA and closed at C . What uniform rotation rate in r/minabout axis AB will cause the pressure to be equal at pointsB and C ? For this condition, at what point in leg BC will thepressure be a minimum?
Torricelli problem. A tank whose shape is obtained by rotating y = x6. At t = 0, the water height is y = 2. The hole at the bottom is of area a = 0.05m2. The gravity acceleration is g = 9.8m/s2. How long will it take for all the water to drain from the tank?
Compute the capillary rise of water between two concentric glass tubes of radius r 1 = 2mm, r 2 = 4 mm with a contactangle ϴ = 20ᵒ. Surface tension = 0.07321 N/ m.
The surface tensions of mercury and water at 60 degrees Celcius are 0.47N/m and 0.0662 N/m, respectively. What capillary height changes will occur in these two fluids when they are in contact with air in a glass tube of radius 0.30mm? Use θ = 130° for mercury, and 0° for water; y = 132.3 kN/m3 for mercury and 9.650 kN/m3 for water. Provide the given along with its solution.
A cylinder is formed by bolting two semicylindrical channelstogether on the inside, as shown in Fig. Thereare 10 bolts per meter of width on each side, and the insidepressure is 50 kPa (gage). Using potential theory for theoutside pressure, compute the tension force in each bolt ifthe fluid outside is sea-level air.
A closed cylindrical vessel, 2m in diameter & 4m high is fully filled with water & rotated to its vertical axis at a constant speed of 12.2 rad/sec. The top is pressurized by 180 KPa. (a) What is the pressure at the center bottom of the cylinder? (b) What is the pressure at the circumference bottom of the cylinder? (c) What is the total hydrostatic force at the sides of the cylinder?
2. Estimate the vacuum pressure that should be created by a suction pump in order to lift a ground water which is 10m below the level ground. Neglect the effect of pipe friction. Draw the figure or free body diagram, and explain its step by step solution. 3. Supposed that air (std.) has a uniform density of 1.2kg/m^3, estimate how high (meters) above the sea level where there exists a zero pressure. Assume that in the given condition, barometric pressure at sea level is 101.325 kPa. Draw the figure or free body diagram, and explain its step by step solution.
Q5: The U-tube shown in figure (3), in filed with water and rotated about a vertical axis (0.15m) to the right of (A) For a gage pressure at (A) equal to zero Determine the rotational speed in (r.p.m)
Derive an expression for the capillary- height change h, as shown, for a fluid of surface tension Y and contact angle 0 be- tween two parallel plates W apart. Evaluate for water at 20°C if W = 0.5 mm.
A 7-cm-diameter solid aluminum ball (SG = 2.7) and asolid brass ball (SG = 8.5) balance nicely when submergedin a liquid, as in Fig. ( a ) If the fluid is water at20 ° C, what is the diameter of the brass ball? ( b ) If thebrass ball has a diameter of 3.8 cm, what is the density ofthe fluid?