*4-76. The device is used to measure a change in temper- ature. Bars AB and CD are made of A-36 steel and 2014-T6 aluminum alloy respectively. When the temperature is at 75°F, ACE is in the horizontal position. Determine the vertical displacement of the pointer at E when the temperature rises to 150°F. 0.25 in.- 3 in. 1.5 in. D

*4-76. The device is used to measure a change in temper- ature. Bars AB and CD are made of A-36 steel and 2014-T6 aluminum alloy respectively. When the temperature is at 75°F, ACE is in the horizontal position. Determine the vertical displacement of the pointer at E when the temperature rises to 150°F. 0.25 in.- 3 in. 1.5 in. D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The beam AB has a moment of inertia I = 475 in4 and rests on the smooth supports at its ends. A 0.75-in.- diameter rod CD is welded to the center of the beam and to the fixed support at D. If the temperature of the rod is decreased by 150°F, determine the force developed in the rod. The beam and rod are both made of A-36 steel.
If the 20-mm-diameter rod is made of A-36 steel and the stiffness of the spring is k = 50 MN>m, determine the displacement of end A when the 60-kN force is applied.
The steel chisel has a diameter of 0.5 in. and a length of 10 in. It is struck by a hammer that weighs 3 lb, and at the instant of the impact it is moving at 12 ft>s. Determine the maximum compressive stress in the chisel, assumingthat 80% of the impacting energy goes into the chisel. Est = 29(103) ksi, sY = 100 ksi
The observation cage C has a weight of 250 kip and through a system of gears, travels upward at constant velocity along the A-36 steel column, which has a height of 200 ft. The column has an outer diameter of 3 ft and is made from steel plate having a thickness of 0.25 in. Neglect the weight of the column, and determine the average normal stress in the column at its base, B, as a function of the cage’s position y. Also, determine the displacement of end A as a function of y.
The rigid bar is supported by the two short white spruce wooden posts and a spring. If each of the posts has an unloaded length of 1 m and a cross-sectional area of 600 mm2, and the spring has a stiffness of k = 2 MN >m and an unstretched length of 1.02 m, determine the vertical displacement of A and B after the load is applied to the bar.
If the elongation of wire BC is 0.2 mm after the force P is applied, determine the magnitude of P. The wire is A-36 steel and has a diameter of 3 mm.
The rotating flywheel-and-shaft, when brought to a sudden stop at D, begins to oscillate clockwise-counterclockwise such that a point A on the outer edge of the flywheel is displaced through a 6-mm arc. Determine the maximum shear stress developed in the tubular A-36 steel shaft due to this oscillation. The shaft has an inner diameter of 24 mm and an outer diameter of 32 mm. The bearings at B and C allow the shaft to rotate freely, whereas the support at D holds the shaft fixed.
The device is used to measure a change in temperature. Bars AB and CD are made of A-36 steel and 2014-T6 aluminum alloy, respectively. When the temperature is at 75°F, ACE is in the horizontal position. Determine thevertical displacement of the pointer at E when the temperature rises to 150°F.
A six-pack is shaken so that the pressurein each can is p = 20 psi. A board is placed onthe six pack and a student(s) weighing Wstands on the board so his weight is evenlydistributed to the six cans. The aluminumproperties are E = 10,000 ksi, Sy = 35 ksi, andν = 0.33. Each can has an average radius ofR = 1.25 in., thickness t = 0.01 in., and lengthL = 4.50 in.(a) Determine the critical weight of thestudent, Wcr , so that a stress element on thesurface of the can is in a state of uniaxial stress.Assume that no support is provided by thecontained liquid and the cans do not fail bybuckling (being crushed). (b) Determine thestrain in the longitudinal direction of the candue to pressure p = 20 psi and force Wcr.(c) Determine the strain in the hoop directionof the can due to pressure p = 20 psi and forceWcr
The A-36 steel bar consists of two segments, one ofcircular cross section of radius r, and one of square crosssection. If the bar is subjected to the axial loading of P,determine the dimensions a of the square segment so thatthe strain energy within the square segment is the same asin the circular segment.
The bellcrank is in equilibrium a) determine the diameter of the bar DE if the normal stress is limited to 100MN/m2.b) Determine the diameter of the pin located at C if the shear stress is limited to 70 MN/m2.c) Determine the crushing force in the support plates in C with a thickness of 6mm.
Air is pumped into the steel thin-walled pressure vessel at C. If the ends of the vessel are closed using two pistons connected by a rod AB, determine the increase in the diameter of the pressure vessel when the internal gage pressure is 5 MPa. Also, what is the tensile stress in rod AB if it has a diameter of 100 mm? The inner radius of the vessel is 400 mm, and its thickness is 10 mm. Est = 200 GPa and nst = 0.3.