4. A bracket is welded to the side of a column and carries a vertical load P, as shown in Fig. 4. Evaluate P so that the maximum shear stress in the 10 mm fillet welds is 80 MPa. 150 220 10 mm fillet weld D x- C 10 mm fillet weld 105 All dimensions in mm. Fig. 4

4. A bracket is welded to the side of a column and carries a vertical load P, as shown in Fig. 4. Evaluate P so that the maximum shear stress in the 10 mm fillet welds is 80 MPa. 150 220 10 mm fillet weld D x- C 10 mm fillet weld 105 All dimensions in mm. Fig. 4

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A tension plate shown below is used to support suspended load "T". Gusset Plate F, = 248 MPa Fu = 400 MPa 200 mm. Determine the allowable tensile capacity of the plate if L= 240 mm. (Assume weld strength is satisfactory)
A rectangular steel plate is welded as a cantilever to a vertical column and supports a single concentrated load P. Determine the weld size if shear stress in the same is not to exceed 140 MPa
A bracket is as shown in figure 2. Determine the uniform weld size for the arrangement. The permissible shear stress of weld material is 80 MPa. Consider the loading condition as shown in figure.
Q.2. A bar with a rectangular cross-section is weld as shown. Determine the size weld, if the pemissible shear stress in the weld 80 MPa. The rectangle area of a fillet weld is equal to [ 2t (b+/)]. 31KN Please send the solution within half an hour and thank you
A 1/4 in fillet weld is to transmit a total force of 12,000 lb. If the allowable unit stress in shear on the weld is 15,800 psi, the minimum effective length of the weld must be A. 5.4 B 4.9 in C. 4.3 in D 3.9 in.
(1) What are the methods used to obtain a good weld when welding steel when the carbon content is high? b) Find the appropriate size and length for the weld joint shown in the figure if the strength is equal to (70000Ib) and the allowable shear stress value is 40ksi and the weld rib dimension is (1/4in)
Question: a) A plate 100 mm wide and 10 mm thick is to be welded to another plate by means of double parallel fillets. The plates are subjected to a static load of 80 kN. Find the length of weld if the permissible shear stress in the weld does not exceed 55MPa. Determine the increase in load carrying capacity if a combination of single transverse double parallel fillet is used the permissible tensile strength of material is 80MPa. b) Draw a neat sketch of double riveted double cover but joint. If 8mm plates with 20 mm diameter rivets having a pitch of 50 mm are joint using double riveted lap joint. The permissible stresses are permissible tensile stress = 120 MPa;Permissible crushing stress= 100 MPa; Permissble shear stess= 150 MPa. Find the strengths and efficiency of joint, taking the strength of the rivet in double shear acoording to the indian boiler standards.
A bracket is welded to the verical column by means of two fillet welds as shown in the figure. Determine the size of the welds, if the permissible shear stress in the weld is limited by 70N/mm^2.
a. figure 1 shows a large pressure vessel fabricated by welding together steel plates of 12 mm thickness as shown. If the stress acting normal to the welds must be less than 80 MPa, what is the largest allowable internal pressure? b. determine the state of strain in the tank when the internal pressure is 0.3 MPa. The elastic modulus (?) of the steel is 200 GPa, and the Poisson’s ratio (?) is 0.3. c. The welded joints are to be replaced with equally spaced rivets (loaded in single shear), each with a diameter of 10 mm and maximum allowable stress of 80 MPa. For an internal pressure of 0.3 MPa inside the tank, determine: (i) The minimum rivet spacing (?) along the circumference of the tank. (ii) The minimum rivet spacing (?) along the height of the tank. d. If the pressure vessel is subjected to a temperature change of 50°C determine the change in height. The co-efficient of thermal expansion for steel can be taken as ? = 11.2 × 10−6 °C−1.
A steel plate, 80 mm wide and 10 mm thick, is joined toanother steel plate by means of a single transverse anddouble parallel fillet welds, as shown in figure. The strengthof the welded joint should be equal to the strength of theplates to be joined. The permissible tensile and shearstresses for the weld material and the plates are 100 and 70N/mm2 respectively. Find the length of each parallel filletweld. Assume that the tensile force passes through the centre of gravity of three welds.
appropriate length of the weld joint shown in the figure if the force is equal to (60000lb) and the operating stress value is (60ksi) and the size of the weld is (1/4in).
A cylindrical air-compressor tank with an inside diameter of 50 mm is to be designed to withstand safely a working pressure of 0.86 MPa. Boiler plate with an allowable tensile stress of 76 MPa. All seams will be butt welds with an expected efficiency of 100 percent. a.) Determine the force per lineal mm of longitudinal seam, b.) Determine the required thickness “t” of wall, c.) Determine the unit stress in the circumferential seam.