40 lb/in. 9 in. FIGURE PS-39 1. Compute the reactions at the supports using the tech- niques shown in Section 5-2. 2. Draw the complete shearing force and bending moment diagrams using the techniques shown in Sections 5-3 through 5-8. 3. Determine the magnitude and location of the maximum absolute value of the shearing force and bending moment.

40 lb/in. 9 in. FIGURE PS-39 1. Compute the reactions at the supports using the tech- niques shown in Section 5-2. 2. Draw the complete shearing force and bending moment diagrams using the techniques shown in Sections 5-3 through 5-8. 3. Determine the magnitude and location of the maximum absolute value of the shearing force and bending moment.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.12.3P: A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0...

See similar textbooks

Similar questions

Answer only in 10minutes Find the maximum bending moment and maximum shearing force
Derive the equations for shear force and bending moment
Write the shear and moment equations and draw the shear and moment diagrams of each figure with step thankss..
1. Find the maximum bending stress - and find the factor of safety 2. find with using the general hear formula - shear stress - and find the factor of saefty
The energy required to shear a 1-in. round bar is approximately 1000 ft-lb. In use, the shearing machine is expected to make a maximum of 40 cutting strokes a minute. The frictional losses should not exceed 18 % of the motor output. The shaft carrying the flywheel is to average 150 rpm. (a) What motor horsepower is required? (b) Assuming a size of flywheel and choosing appropriate f C, find the mass and sectional dimensions of the rim of a cast-iron flywheel. The width of the rim is to equal the depth and is not to exceed 3 ½ in. It would be safe to assume that all the work of shearing is supplied by the kinetic energy given up by the flywheel.
Solve it by method of least work . Also draw bending moments and shear diagrams.. Plz explain each step clearly so I can understand it by myself
A shaft is subjected to a torque of 28 kNm and a maximum bending moment of 25 kNm. The shaft is solid with a diameter of 125 mm. Using the Mohr circle method find the values for the principal stresses and themaximum shear stresses on the shaft i)Construct the Mohr circle on the graph paper provided. ii) Using the Mohr circle method find the values for the principal stresses and the maximum shear stresses on the shaft.iii) Show the orientations of the planes on which the principal stresses act on a rotatedelement
A solid and a hollow shaft are made of same material. The diameter of the solid shaft is 300 mm and has the same cross-sectional area as a hollow shaft with inside diameter of 250 mm. Find the ratio of the Angles of twist in equal lengths of these shafts, when stressed to the same intensity
Draw the free-body diagram for the portion of machine structure shown in Figure 1. Determinethe reactions at the supports and draw the complete shear-force and bending-moment diagrams
A shaft ABCD is shown in Figure 3 with total length, L = 2.1 m. The shaft BC is hollowwith inner and outer diameters of 90 mm and 120 mm, respectively. Shafts AB and CDare solid with diameter d. Given the torque at A, B, C and D is 6 kNm, 14 kNm, 26 kNmand 6 kNm, respectively.a) Determine the maximum and minimum shearing stress in shaft BC. b) Calculate the required diameter, d of shafts AB and CD if the allowable shearingstress in these shafts is 65 MPa.
Find reactions and plot shear force and bending moment diagrams
problem 3 Find the Shear Moment Diagram of the following problems usingONLY AREA METHOD.