Answered: 5. In the following typical control…

5. In the following typical control system B.D, which block would represent the controller unit: R(s) E(s) (s)Pn G2 Y(s) U(s) G1 G3 G4 a) G1 b) G2 c) G3 d) G4

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter22: Basics Of Electronics And Computer Systems

Section: Chapter Questions

Problem 4RQ: Means that data concerning the effects of the computers commands are fed back to the computer as an...

See similar textbooks

Related questions

Q: The property of a sys whether one considers the whole system or a part of it,

A: Answer: Intensive property. These are the properties of a system whose values are independent of the…

Q: The state-equations of the control system shown in Fig.1 is: U(s) 2 Y(s) s(s? + 3s + 12)

A: Given: Control system,

Q: In time domain analysis of a control system, we should use the input signals which let the system…

A: Time Domain Analysis of a Control system is mainly consists of analysis of physical signals…

Q: (a) A feedback control system has the following characteristic equation. 5³+(4+ K) s² + 6s+ 8(K + 2)…

Q: The state transmission matrix of the system whose state-space [2³] =102² J] [₁ и 0 a. b. C. O d. c.…

A: The state transmission matrix of the system is given below, x˙1x˙2=01α20x1x2+01u

Q: 9 Reduce the following block-diagram into one block. (Describe the control system with one transfer…

Q: Figure Q3 shows a spring-mass system composed of three masses suspended vertically by a series of…

Q: The closed-loop system transfer function of a control system is

Q: One of the beneficial applications of an automotive control system is the active control of the…

Q: 7. What is the response to unit step function input when all initial conditions are zero. S(S + 3)…

Q: A satellite single-axis amplitude control system can be represented by the block diagram is as shown…

A: Data given- K,a & b are control parameters j = spacecraft moment of inertia J = 7.8E+08 K =…

Q: For the liquid level control system given below, the input is q,(t) and the output is h3(t) then…

A: Process Control System- Process control is the main part of any industry to process, monitor, and…

Q: In a process, it is desired to heat oil to 300°C as shown below. What is the objective variable?…

A: The heat exchange in which one of the fluids does not have change in temperature while the other…

Q: What is the control plane's principal function?

A: Introduction: In a network there are various planes have different works. Every plane or part of…

Q: Calculating the separation and / or joining angles in the negative feedback control circuit, if any,…

A: Given open loop transfer function G(s)=s+1s2-4s+5 The poles of the open loop transfer function is…

Q: Look at the block diagram for the dynamic model of the hydraulically actuated system in Fig where:…

Q: The delay in the response of any feedback system is called as system lag. Select one: O True O False

A: System: It is a collection of the parts which are arranged in a systematic manner to gain a specific…

Q: In order to stabilize the system, we use a P controller in c U(s) 1 Y(s). K s3+5s² + 4s Determine…

A: Given:

Q: After some engine model replacement, an aircraft model is experiencing some aggressive nose up…

Q: Please represent the system in State-Space where OL(t) is output. N1 k2 N mirad d2N-m-s/rad N2 N3 kl…

Q: i) Process Element (ii) Feedback Element (iii) Control Element (iv) Correction Element

A: Given: To identify: (i) Process Element (ii) Feedback Element (iii) Control Element (iv) Correction…

Q: 2. A model for an airplane's pitch loop is shown below. Find the range of K that will keep the…

Q: The raising time of a first order system is the time required to reach 90% of the final value.…

A: The rise time of a system is the time taken to reach from one state to another. Generally, in…

Q: (Can someone help me with this just need a P&ID solution meeting the requirements and explanation.…

A: A P&ID gives a point by point graphical portrayal of the genuine interaction framework that…

Q: Which of the following gate will have high output if at least any one input is high ?. a. NAND Gate…

A: Given Statement: Which of the following gate will have high output if at least any one input is…

Q: 5. You need to know the resolution of the control. How many counts are there for 1 degree of motion?

A: Solution:

Q: 5. Recall that dG = -3dT + VdP. Show that for constant T %3D (P)- HH20(0 (P) = VH20 (P-P') %3D

Q: One of the features of the Turing machine is that it has an external memory which remembers…

A: True

Q: Question 1: For the electromechnanical system given below: a) Draw the detailed block diagram of the…

A: a) the block diagram for the given figure

Q: is design of mechanism to produce a output motion for a given input motion. O a. Analysis, required…

A: Analysis is design of mechanism to produce a required output motion for a given input motion.

Q: The ratio of output to input of a system is known as Transfer function. Select one: O True O False

A: The ratio of the Laplace transform of the output to that of input is called transfer function.

Q: 2. A P&ID of a phosphate pebble dryer is shown in the figure below. A feeder (table feeder) moves…

A: Given : To find : Action of moisture controller

Q: 0 0 1 1 1/ -zero codewords in the group code made

A: Given a 3×5 matrix. H=010011010100111

Q: Process control can be defined as the act of controlling a final control eement to change the…

A: Process control is an important part in maintaining the output of a system within a desired range by…

Q: The given system |accuracy. has

A: Let discuss about accuracy of given figure.

Q: State the control goal. Identify the input and output variables for the process. Identify the…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: A factory produces four products, D, C, B, A, using two M2, M machines, the time taken and the cost…

Q: 15 The figure below represents a time response of a control system. What is it? * Unit-step response…

A: The above given graph is of

Q: A proportional controller is used to control the height of water in a tank where the water level can…

A: Given Data The initial water level is: 0 The final water level is: 4.0 m The required height of the…

Q: The feedback signal of the following system is, Z(s)=.

A: From the figure we write the relationship between the blocks and solve.

Q: Define linear impulse.

A: When a force F is applied on a object over a period of time then in that case the impulse is…

Q: In a negative feedback system ,the error can be calculated by subtracting the feedback value with…

A: In a negative feedback system, the error can be calculated by subtracting the feedback value with…

Q: Commanded elevator Elevator Elevator deflection actuator deflection Pitch Vehicle command Pitch gain…

A: Initial Step According to Given Data:-

Q: The above table on the right shows input-output (steady-state) relationsh o be identified. Knowing…

Q: You are the mechatronics engineer of a manufacturing plant. You decide to perform an analysis on a…

A: Both mid-ordinate rule and Simpson's rule are used to approximate the value of the definite…

Q: Feedback control systems are: Select one: O a. Insensitive to both forward and feedback path…

A: In industrial engineering, feedback control systems are incorporated to modify or fluctuate the end…

Q: Q7) Give the State Machine for detecting the sequence "1010" from a serially coming data.

A: The state diagram is visual representation of the sequence.It shows the internal states and…

Q: 4(a) Describe, in your own words, the difference between a deterministic finite automa- ton and a…

A: Hi and thanks for the questions. Since you have asked more than one questions, we will solve the…

Concept explainers

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.

Question

5. In the following typical control system B.D,
which block would represent the controller
unit:
R(s)
E(s)
(s)Pn
G2
Y(s)
+
U(s)
G1
G3
G4
a) G1
b) G2
c) G3
d) G4

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

EXPERIMENT TITLE : PID CONTROLLER IN LEVEL CONTROL SYSTEM OBJECTIVE:To demonstrate the characteristic of P,PI and PID controller response on a level controller system. Based on the topic and objective given,please make a clear introduction.
Example 1.1 Figure 1.5 shows the block diagram of a closed-loop flow control system. Identify the following elements: (a) the sensor, (b) the transducer, (c) the actuator, (d) the transmitter, (e) the controller, (f) the manipulated variable, and (g) the measured variable. In the figure above, the (a) sensor is labeled as the pressure cell. The (b) transducer is labeled as the converter. However, there are two converters: one for converting pressure to current, and another converting current to pressure for operating the actuator. The (c) actuator is labeled as the pneumatic valve. The (d) transmitter is labeled as the line driver. The (e) controller is labeled as the PLC. The (f) manipulated variable is labeled as the pressure developed by the fluid flowing through the orifice plate. The (g) measured variable is the flow rate of the liquid.
Means that data concerning the effects of the computers commands are fed back to the computer as an input signal.
A stock-flow system models the level of water in a lake. Near a certain equilibrium point, there are three feedback loops: an amplifying feedback loop with strength of +0.55 per month, a stabilizing feedback loop with strength of -0.09 per month, and an amplifying feedback loop with strength of +0.79 per month. Calculate the strength of the overall feedback.
Solev the question using matlab
You are the mechatronics engineer of a manufacturing plant. You decide to perform an analysis on a robot arm of the assembly line with the objective of optimizing its performance. After taking several readings of the speed of the arm’s end effector, you approximate its velocity to the function given below. v(t) = -t4 + 5t3 - 7t2 + 3t + 0.22 0 =< t =< 3 where the velocity is in ms-1 d) Knowing that the distance travelled by an object is the area under its velocity-time graph, determine the distance travelled by the end effector on the interval 0 =< t =< 1 by using the mid-ordinate rule. Simpson’s rule correct to 3 decimal places using four intervals. e) Calculate the same distance as in (d) above by using the appropriate definite integral. f) Compare the distances you calculated in (d) and (e) above and comment on the accuracy of the two methods you used in (d)
1. Give an example of open loop and closed loop system (one example each). Also state the input, control system, feedback and output parameter. Example. 1. Open Loop - Water Heater: Input - Water Temperature (Cold) System - Heating Element Output - Water Temperature (Hot) 2. Closed Loop - Air-conditioning System Input - Desired Room Temperature Control - Motor controller/Compressor/ACU Feedback - Temperature Sensing Output - Room Temperature
TIME DOMAIN MODELING AND RESPONSE FOR CONTROL SYSTEMS
Do not do the matlab part
Calculating the separation and / or joining angles in the negative feedback control circuit, if any, given as Controlling (K) and Controlled G (s) = (s + 1) / (s2-4 * s + 5) Explanation: The roots of the equation (s2-4 * s + 5); s1 = 2 + 1 * j and s2 = 2-1 * j and the system Transfer Function is TF (s) = K * G (s) / (1 + K * G (s)). a. There are split angles up to (+108.435) and (-108.435) b. There are split angles as much as (+71,565) and (-71,565) c. There are conjunction angles of (+90) and (-90). D. There are separation angles as much as (+18.435) and (-18.435). E. There are no separation and convergence angles.
Please solve this exercise found in NISE, control engineering book. Please solve this using the translational mechanical system transfer fucntion method and kindly explain as well since this is an exercise to master the topic. Thank you very much!
Draw the state diagram of a High-Level State Machine that describes the operation of a light sequencer for a traffic light. Green should be on for 100 clock pulses, yellow for 20 clock pulses, and red for 70 clock pulses, for this particular street direction.