8. The following titration data was collected in a lab. Based on the results, determine the concentration of the aqueous sulfuric acid acid. Concentration of NaOH used: 0.50 M Volume of NaOH used: 50.0 mL Indicator: phenolphthalein Endpoint color change: olorless to pale pink Table 1 Volume of sulfuric acid Required Burette reading (mL) Trial 2 Trial 3 Trial 1 Final reading 31.28 39.17 46.70 1.18 9.08 16.62 Initial reading Volume H2SO4 used (mL)

8. The following titration data was collected in a lab. Based on the results, determine the concentration of the aqueous sulfuric acid acid. Concentration of NaOH used: 0.50 M Volume of NaOH used: 50.0 mL Indicator: phenolphthalein Endpoint color change: olorless to pale pink Table 1 Volume of sulfuric acid Required Burette reading (mL) Trial 2 Trial 3 Trial 1 Final reading 31.28 39.17 46.70 1.18 9.08 16.62 Initial reading Volume H2SO4 used (mL)

Appl Of Ms Excel In Analytical Chemistry

2nd Edition

ISBN:9781285686691

Author:Crouch

Publisher:Crouch

Chapter12: Spectrochemical Methods

Section: Chapter Questions

Problem 15P

See similar textbooks

Similar questions

A 50.00-mL aliquot of solution containing 0.358 of MgSO4 (FM 120.37) in 0.500 L required 38.08 mL of EDTA solution for titration. How many milligrams of CaCO3 (FM 100.09) will react with 1.00 mL of this EDTA solution?
A 10.00-mL aliquot of a known HCl solution (3.800 g/L) was titrated with a 4.100 g/L NaOH solution. Calculate the range of the blank corrected titration volumes using the titration data below: Blank Trial 1 Trial 2 Trial 3 Initial Volume (mL) 12.50 0.50 12.30 34.75 Final Volume (mL) 13.10 10.45 22.35 45.27
H8. a 10 ml sample containing Ni was back titarted againat 0.0575 M EDTA. 10 ml concentrated amonia was added to the sample and 100 ml of water with 0.02 indicatore. the averge of 3 titration is 14.76667 ml. what is the Ni content g/L?
100 mL water sample was subjected to DO analysis using the Winkler method. The initial reading of the titrant (0.025 M Na2SO3) in the buret was 2.51 mL. The endpoint was obtained and the final reading was 7.07 mL. A blank was also titrated and 0.75 mL of the titrant was consumed. Compute for the amount of DO (mg/L) in the sample.
Determine the relationship between the observed/apparent value (EX) VERSUS that of the true value (ET) for the quantity being sought by writing either <, >, or = on the space provided Determination of water hardness using complexometric titration. During sample analysis (ppm CaCO3), the volume for blank correction was not subtracted to the volume of titrant. EX Blank 1 ET
A dilute peroxide solution was prepared by quantitatively diluting 10 mL stock H2O2 (MW = 34.0147) to 250mL using a volumetric flask. 50 mL aliquot of the diluted peroxide solution was titrated using the previously standardized KMnO4 in problem 1. Titration of the sample required 29.00 mL titrant and the blank containing 50 mL 1:5 H2SO4 required 0.75 mL of the standard KMnO4. Calculate the concentration in %w/v of the stock H2O2. (Hint: H2O2 produces O2 under acidic condition). Follow sig. Fig
What is the concentration of Mn2+ in a solution with an analytical MnY2- concentration of 0.025 M at pH7? Kmny = 6.2 x 1013 a4 = 4.8 x 10-4 A 9.2 × 10-7 M B 8.4 × 10-13 M C 4.0 × 10-16 M D 2.0 × 10-8 M
A 0.500-g sample containing BaBr2 (FM = 297.14) is dissolved in 50 mL of distilled water. Titrating with 0.0400 M AgNO3 requires 25.00 mL to reach the Mohr endpoint. A blank titration requires 0.50 mL to reach the same endpoint. Calculate the %w/w BaBr2 in the sample. Please provide a complete solution.
Using the term u of KSP experimental procedure the 6 p.m. As you add 5 ml of .004M AgNo to 5ml of .0025M K2CrO4. Is either of these reagents in excess? If so which one?
1. Recreate the graph in the potentiometric titration of a diprotic acid (FW=116.07) given the following data. Show necessary computations.Mass of acid = 0.1032 gKa1 = 3.21 × 10-5Ka2 = 8.85 × 10-8pH at EP1 = 5.77pH at EP2 = 7.69NNaOH = 0.05 NNote: Label EP1 and EP2. The graph should show the actual volume of titrant (mL) and pH level at ½ EP1, EP1, ½ EP2, and EP2.
The zinc contained in a 0.7555-g sample of foot powder was titrated with 21.27 mL 0.01645 M EDTA. Find the percent Zn (MM=65.41) in the sample.
100.0 cm3 overall volume of buffer solution is to be prepared from acetic acid and sodium acetate. Start from 10.0 cm3, 1.0 mol/dm3 sodium acetate and calculate the volume of 1.0 mol/dm3 acetic acid necessary for the buffer solution of pH of 4.95. Ka(CH3COOH) = 1.75*10-5