8.111 The flowrate between Tank A and Tank B shown is to be increased by 30% (i.e., from Q to 1.30Q) by the addition of a second pipe indicated by the dotted lines running from Node C to Tank B. If the elevation of the waterline in Tank A is 25 ft above the waterline of Tank B, determine the diameter D of this new pipe in feet. Neglect minor losses and assume the friction factor in each pipe is f = 0.02. A 6-in. diameter; 600 ft long C 6-in. diameter; 500 ft long Diameter D, 500 ft long B

8.111 The flowrate between Tank A and Tank B shown is to be increased by 30% (i.e., from Q to 1.30Q) by the addition of a second pipe indicated by the dotted lines running from Node C to Tank B. If the elevation of the waterline in Tank A is 25 ft above the waterline of Tank B, determine the diameter D of this new pipe in feet. Neglect minor losses and assume the friction factor in each pipe is f = 0.02. A 6-in. diameter; 600 ft long C 6-in. diameter; 500 ft long Diameter D, 500 ft long B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Reservoir X (Elevation 369m) supplies water to reservoir Y (Elevation 195m) thru a 400 mm pipe. A turbine is installed in the same level with Reservoir Y. The total system flow is 220 gpm determine the the output power in Hp if the turbine is 65% efficient and the total headloss of the system is 4.5m.
An air-distribution system for an industrial complex is show in the attached figure, having flow rates as indicated. The velocity in the main duct should not exceed 400 m/min. Using equal pressure drop (Δp/ΔL) in the main duct and balanced pressure drop in the branch line and taking the depth of duct as 2,000 mm throughout, determine the following: A) The height of the main duct B-C dimension in millimeters. B) The height of the branch duct B-E dimension in millimeters.
Question 8 Two reservoirs are connected by a pipe whose total length is 360m.From the upper reservoir the pipe is 300mm in diameterfor a length of 150m and the remaining 210m is 450mm in diameter.The difference in water levels between the two reservoirs are 8m.Take f=0.006 for the smaller pipe and f=0.005 for the larger pipe.If all the changes in pipe sections are sharp and sudden, calculate the flow rate which can be delivered.
The three-tanks system in figure are interconnected as shown. Compute the flowrate in each pipe, given: L1 = 2000 m, L2 = 2300 m, L3 = 2500 m; D1 = 1 m, D2 = 0.60 m, D3 = 1.20 m; f1 = 0.013, f2 =0.020, f3 = 0.023.
The diameter of a pipe carrying oil(s=0.92) changes gradually from 400 mm at A to 600 mm at B. Point A is 3.6 m lower than B. If the pressure at A is 70 KPa and that at B is 49 KPa when 140 L/s is flowing, determine the direction of flow; (b) the frictional loss between the two points.
Water flows from a main line to a lateral as shown. The flow in the mainline is 1.63 ft3/s. Measurements show that the pressure at point 1 is 34 psi and at point 3 is 33.5 psi. Determine the velocities at 2 and 3. Assume the distance between the centerline of the main line and point 3 is 5 inches.
the hydraulic radius of a pipe with a diameter of 12mm is
Water at 38°C flows from A to B through 244 m of average 300-mm-I.D. cast iron pipe (e = 0.00061 m).Point B is 9.1 m above A, and the pressure at B must be maintained at 138 kPa. If 0.222 m3/s is to flowthrough the pipe, what must be the pressure at A? Ans. 314 kPa (show the complete solution with diagram) [Note: Indicate the formula used in determining the friction factor. (Colebrook Equation, Haaland Equation, andor Swamee Jain Equation). If not given, Use properties of fluid based ontemperature available ontheinternet.E.g. (density, viscosity). Apply roughness of pipe values from https://www.pipeflow.com/pipe-pressure-drop-calculations/pipe-roughness]
For the Pipe shown Q=4250 gallons per minute (gpm), P1=132 kPa and P2 = 211 kPa. If the pipe carries a special fluid of SG=1.2, determine the total head lost.
A vessel is being filled with water through an inlet at section 1 having a diameter of 40 mm and a faucet at section 3. The velocity at section 1 is given as 5 m/s, while the discharge at section 3 is given as 0.012 m^3/ s. Assume constant water level. Use 60 mm for the diameter of the outlet at section 2. A. What is the discharge at section 2? B. What is exit velocity at section 2? C. If the water level varies and the velocity at section 2 is 8m/s find the rate of change when d is equal to 1000mm?
An orifice having an area of 0.0003 m² is located on the vertical side of a tank. The tank has a constant cross sectional area of 0.40 m². It takes 312 seconds to lower the head from 1.20 m to 0.60 m. Using c=0.60, which of the following most nearly gives the head in meter after 240 seconds from an initial head of 1.20m?
From a very large tank with an absolute pressure of 3 bar, the water is discharged to the atmosphere by means of 2 smooth pipes of 100 m length, 1 m and 50 m long, connected in series. The height difference between the water level in the tank and the outlet is 50m, and the diameters of the pipes are 50mm and 100mm, respectively. In addition, a 500kPa turbine is placed on the 2nd Pipe. a) Draw the system roughly, show the dimensions on it.b) Calculate the exit velocity of the water from the 2nd pipe, ignoring the local losses.