A 480 V, 60 Hz ,Delta Connected, Four Poles Synchronous Generator has A Direct Axis Reactance of 0.1 Ohm, and Quadrature Axis Reactance of 0.075 Ohm .Its Armature Resistance May be Neglected. At Full Load, This Generator Supplied 1200 A , at A Power Factor Of 0.8 Lagging. 1-Find The Internal Generated Voltage (E), of This Generator at Full that it has A Cylindrical Rotor of Reactance Xd ( Xd =Xs). Load . Assuming 2- Find the Internal Generated Voltage E, of this Generator at Full Load. Assuming It has Salient Pole Rotor.

A 480 V, 60 Hz ,Delta Connected, Four Poles Synchronous Generator has A Direct Axis Reactance of 0.1 Ohm, and Quadrature Axis Reactance of 0.075 Ohm .Its Armature Resistance May be Neglected. At Full Load, This Generator Supplied 1200 A , at A Power Factor Of 0.8 Lagging. 1-Find The Internal Generated Voltage (E), of This Generator at Full that it has A Cylindrical Rotor of Reactance Xd ( Xd =Xs). Load . Assuming 2- Find the Internal Generated Voltage E, of this Generator at Full Load. Assuming It has Salient Pole Rotor.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.11P

See similar textbooks

Similar questions

A short shunt compound generator has an armature; series field and shunt field resistances of 0.031Ω, 0.04Ω and 100Ω respectively. At rated load condition, the terminal voltage is 400V while the armature is developing an emf of 409V. Find the kW delivered to the load at rated condition.
A 3 phase 4MVA, 12 kV star connected synchronous generator has Zs= 0.8+J30 ohm. Using circle diagram only, find: 1. The output power developed at unity power factor with excitation equal to 1.25 of rated voltage. 2. The load angle and power factor if the generator supplies (1500 KW) at rated voltage and excitation lequal to (1.2) of rated voltage. 3. Repeat part (2) when .armature resistance is neglected
A 220V short-shunt compound generator has armature resistance, series field resistance and shunt field resistances of 0.6, 0.44 and 300 - 16 respectively. If the generator supplies a 10+16 kW load at a rated voltage, find the induced voltage in the armature. Ignore armature reaction. Find the efficiency if the mech and core loss is 500W
A three-phase, Y-connected, 220 V, 5 kVA, salient-pole synchronous generator is employed to supply power to a load with unitary fp. By means of a slip test, the direct-axis synchronous reactance is determined to be 12 Ω and the quadrature-axis synchronous reactance, 7 Ω. Consider that the rated current is delivered to the load at the rated voltage and that the armature resistance is negligible. (a) Calculate the corresponding value of the excitation voltage. (b) What is the value of the internal phase shift angle? (c) What is the value of the power angle?
In a long-shunt compound generator, the terminal voltage is 220 Vwhen generator delivers 110 A. Determine (a) induced emf and (b)total power generated. Given that shunt field, series field,diverter and armature resistances are 90 Ω, 0.025 Ω, 0.04 Ω and0.03 Ω respectively.
EMachines A 100 MVA, 11.5 kV 0.8 pf lagging 50-Hz two pole Y-connected synchronous generator has a per-unitsynchronous reactance of 0.8 and per-unit armature resistance of 0.012. A. What is its synchronous reactance and armature resistance in ohms?B. What is the magnitude of the internal generated voltage at the rated conditions? What is its torque angleat these conditions?C. Ignoring losses in this generator, what torque must be applied to its shaft by the prime mover at fullload?
A long shunt compound DC generator delivers a load current of 150A at 230V and has armature, series field and shunt field resistances of 0.032, 0.015 and 92Ωrespectively. Calculate (i) induced emf (ii) total power generated and (iii) distribution of this power (iv) voltage regulation
(a) A short shunt cumulative compound dc generator supplies 6kW at 235V. The Shunt field resistance, Series field resistance and Armature resistances are 8012, 0.192 and 0.22 respectively. Calculate the induced emf and load resistance.
Two similar 6,600-V, three phase generators are running in parallel on constant-voltage andfrequency bus bars. Each has an equivalent resistance and reactance of 0.05 Ω and0.5 Ω respectively and supplies one half of a total load of 10,000 kW at a laggingp.f. of 0.8, the two machines being similarly excited. If the excitation of onemachine be adjusted until the armature current is 438 A and the steam supply to theturbine remains unchanged, find the armature current, the e.m.f. and the p.f. of theother alternator.
Problem: The field current of a 100-kW, 250V shunt generator is 5A when delivering power at rated terminal voltage and rated load current. The combined armature and brush resistance is 0.1 ohm. 1.)Calculate the generated power in kW. 2.)What is the electrical efficiency? * Formatt: given required solution answer
A 3 phase, star connected synchronous generator supplies current of 10A having phase angle of 20º lagging at 400V. Find the load angle and the components of armature current Id and Iq if Xd = 10 ohm and Xq = 6.5 ohm Assume armature resistances to be negligible
A 480 V, 50 Hz, Y-connected six-pole synchronous generator has a per-phase synchronous reactance of 1.0 Ω. Its full-load armature current is 60 A at 0.8 PF lagging. Its friction and windage losses are 1.5 kW and core losses are 1.0 kW at 60 Hz at full load. Assume that the armature resistance (and, therefore, the I2Rlosses) a.b. i.ii. iii.c. d. e.can be ignored. The field current has been adjusted such that the no-load terminal voltage is 480 V. What is the speed of rotation of this generator?What is the terminal voltage of the generator if :it is loaded with the rated current at 0.8 PF lagging;it is loaded with the rated current at 1.0 PF;it is loaded with the rated current at 0.8 PF leading.What is the efficiency of this generator (ignoring the unknown electrical losses) when it is operating at the rated current and 0.8 PF lagging?How much shaft torque must be applied by the prime mover at the full load? how large is the induced counter-torque?What is the voltage regulation of this…