A beam is 18m long and it's one overhang side is subjected to a uniform load of 6kN/m. f the modulus of elasticity of the beam is 200GPA and its moment of inertia is 250x10mm (Use Area-Moment Method) 1. What is the slope at the overhang that carries no load 2. What is the deflection at the overhang that caries the uniform load of 6kN'm 6kN/m A 2m B 8m Bm

A beam is 18m long and it's one overhang side is subjected to a uniform load of 6kN/m. f the modulus of elasticity of the beam is 200GPA and its moment of inertia is 250x10mm (Use Area-Moment Method) 1. What is the slope at the overhang that carries no load 2. What is the deflection at the overhang that caries the uniform load of 6kN'm 6kN/m A 2m B 8m Bm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.7.3P: Beam ACB hangs from two springs, as shown in the figure. The springs have stiffnesses Jt(and k2^ and...

See similar textbooks

Similar questions

.2 A ligmio.irc ii supported by two vorlical beams consistins: of thin-walled, tapered circular lubes (see ligure part at. for purposes of this analysis, each beam may be represented as a cantilever AB of length L = 8.0 m subjected to a lateral load P = 2.4 kN at the free end. The tubes have a constant thickness ; = 10.0 mm and average diameters dA = 90 mm and dB = 270 mm at ends A and B, re s pec lively. Because the thickness is small compared to the diameters, the moment of inerlia at any cross section may be obtained from the formula / = jrrf3;/8 (see Case 22, Appendix E); therefore, the section modulus mav be obtained from the formula S = trdhlA. (a) At what dislance A from the free end docs the maximum bending stress occur? What is the magnitude trllul of the maximum bending stress? What is the ratio of the maximum stress to the largest stress (b) Repeat part (a) if concentrated load P is applied upward at A and downward uniform load q {-x) = 2PIL is applied over the entire beam as shown in the figure part b What is the ratio of the maximum stress to the stress at the location of maximum moment?
A cantilever beam of a length L = 2.5 ft has a rectangular cross section {b = 4in,, h = Sin,) and modulus E = 10,000 ksi. The beam is subjected to a linearly varying distributed load with a peak intensity qQ= 900 lb/ft. Use the method of superposition and Cases 1 and 9 in Table H-l to calculate the deflection and rotation at B.
Beam ACB hangs from two springs, as shown in the figure. The springs have stiffnesses Jt(and k2^ and the beam has flexural rigidity EI. What is the downward displacement of point C, which is at the midpoint of the beam, when the moment MQis applied? Data for the structure are M0 = 7.5 kip-ft, L = 6 ft, EI = 520 kip-ft2, kx= 17 kip/ft, and As = 11 kip/ft. Repeat part (a), but remove Af0 and instead apply uniform load q over the entire beam.
Finite Element Method It is made of steel material (210GPa) for the beam given below, beam cross section (dimensions mm) is given below. According to this a) Find the displacement that occurs at each node b) Find the reaction forces
A beam of uniform rectangular section 200 mm wide and 300 mm deep is simply supported at its ends. It carries a uniformly distributed load of 9 KN/m run over the entire span of 5 m. if the value of E for the beam material is 1 X 104 N/mm2 , find the slope at the supports and maximum deflection. Give me complete solution based on the given above. Again I need to ask the same question since you gave me a wrong answer before.
A fixed beam AB, 5 m long, is carrying a point load at its centre. The moment of inertia of the beam is 60 x 106 mm4 and modulus of elasticity for beam material is 2.2 x 105 N/mm2. End moments are taken to be 40 kN-m. The load at the centre is
For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the cantilever beam, (b) the deflection at B, (c) the deflection at the free end, and (d) the slope at the free end. Assume that EI is constant for the beam. Let w = 15 kN/m, L = 3.5 m, E = 185 GPa, and I = 110 x 106 mm4
A Rayleigh’s method approximation for the first flexural natural frequency of a beam that is simply supported at both ends was using the guessed shape lx^2-x^3. How many of the boundary conditions are satisfied with this guess?
For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the cantilever beam AB, (b) the deflection at the free end, and (c) the slope at the free end. Assume that EI is constant for the beam. Let w0 = 6 kN/m, L = 5.5 m, E = 195 GPa, and I = 140 x 106 mm4.
For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the beam, (b) the location of the maximum deflection, and (c) the maximum beam deflection. Assume that EI is constant for the beam. Let w = 11 kN/m, L = 4.5 m, E = 185 GPa, and I = 140 x 106 mm4.
Answer only Civil engineering A cantilever beam of length L and flexural modulus El is subjected to a point load P at the free end. The elastic strain energy stored in the beam due to bending (neglecting transverse shear) is
Find expressions for shear force V andmoment M at x = x0 of beam AB in terms of peakload intensity q0 and beam length variable L.Let x0 = 2L/3.