A circular rod of a diameter of 100 mm is subjected at its free end to force F1 = 50N and F2=(200j - 100k)kN as shown in the figure. Determine and draw the state of stresses in small infinitesimal cubic elements located at points M and N on the cross section of A.

Q: Q1/A steel bar ABCD (4m) long is subjected to forces as shown in Figure. Find the stresses in each…

A:

Q: 75 mm When a force P of 750 N is applied to the pedal shown in the figure, find the diameter (mm) of…

A: Given data: The applied force, P = 750 N. The shear stress in the pin, τ = 40 MPa. Draw the…

Q: Q2) For the problem shown in the figure, - Find the axial displacement at the end B - Determine the…

A: for solution refer below images.

Q: A force of 40 kN is applied to the edge of the member shown in Figure below. Neglect the weight of…

A:

Q: The solid 1.25-in.-diameter rod shown in Figure is subjected to a uniform axial distributed loading…

A:

Q: A steel pipe assembly supports aconcentrated load of (P = 22 kN) as shown in Figure. The outside…

A: Calculate the moment about point H due to load P.   MH=P370 mm×1 m1000 mm=22 kN×1000 N1 kN370 mm×1…

Q: 1. A steel thick-walled cylinder has an inner diameter of 25mm and an outer diameter 110mm. The…

A:

Q: The circular rods AB and BC is joined at B and fixed at the wall at A, as shown in the figure.…

A:

Q: A steel bar with a diameter of 100 mm is rigidly attached to the wall and carries the loads shown in…

A: Given: The diameter of shaft, d = 100 mm = 0.1 m The torque acting on the shaft, T = 8 kN.m The load…

Q: The structure of hook is made such that it is in round shape with diameter d= 20mm as shown in the…

A:

Q: For the figure shown determine the value of the maximum normal stresses, due to the change of…

A: given; lets take reaction force at E=R1lets take reaction force at F=R2

Q: 10 KN 20 KN / m 5 KN / m A B SIMPLE STRESSES 5 KN / m D 5 KN / m F 50 KN-m E 3. Points C and D of…

A: Given DataP=10kNw1=5kN/mw2=20kN/m

Q: For the plane truss shown in the Figure (a) Determine the displacements of nodes and (b) The…

A: Given: To find: Displacements of nodes

Q: Q3 - A thin-walled cylindrical vessel has an internal diameter of 1m and a thickness of 10 mm…

A: pressure:- Pressure is defined as the physical force exerted on an object. The force applied is…

Q: A solid bar has a diameter of 40 mm and subjected to the loadings shown in Figure 2. The supports at…

A:

Q: Neglecting the weight of the bar as shown in the figure, determine the stress in each rod if the…

A:

Q: Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1)…

A:

Q: Q4-A vertical force of 178 Nis applied to a pipe wrench whose handleis vertical to the z-axis as…

A: Given, Force, F=178NInside diameter, di=2.66cmOutside diameter,do=3.34cm Moment of Inertia,…

Q: A bolted connection between a vertical column and a diagonal brace is shown in the figure below. The…

A:

Q: For the assembly shown in the figure below, Determine the state of stress at point A on the cross…

A:

Q: The built-up shaft in figure consists of a pipe AB and a solid rod BC. The pipe has an inner…

A: Given : outer diameter of pipe AB, Do = 28 mm inner diameter of pipe AB, Di = 20 mm diameter of rod…

Q: The coupling as shown in figure is made from steel has rectangular cross section is designed to…

A:

Q: Q1/ The aluminum bar has been subjected to axial loads at the positions shown in Figure below.…

A:

Q: A circular bracket with a diameter of 100 mm is fixed to a wall as shown in the figure below.…

A:

Q: 0.8 m 0.4 m В 0.6 m 1.6 m P = 1.2 kN 2 m The rigid beam AB is hinged to a support at A and supported…

A: Suppose angular displacement of beam is δθ;   then, stretch in wire C and D are  0.6 x δθ &  1.6…

Q: In the figure shown, determine the normal stresses at AD • , shearing stress at + and BC bolt D • ,…

A: Solution: The free body diagram of the EDC is shown above, we need to find the reactions RD and RC…

Q: The foundation bolt is shown in the below figure a force F = 300 N. The bolt material is wire of…

A:

Q: For the beam and loading shown in the figure below, determine: 1- The normal and shearing stresses…

A: Part 1 From fig we can say that the forces that play a vital role to form normal and shear stress…

Q: D16. For the truss shown in figure determine the displacements at point B and stresses in the bars…

A: To determine the stresses in Part AB and BC.

Q: A circular bracket with a diameter of 100 mm is fixed to a wall as shown in the figure. Determine…

A:

Q: Observe the figure below. Determine the following: a. axial stress on the shank if the load applied…

A:

Q: Column is manufactured using concrete (E=4.2×10^3 ksi) and reinforcement is done by A-36 steel rods…

A:

Q: Determine the total stress at point A on the cross section a-a in the figure below. 400 kN la -0.5…

A: Draw a diagram showing the neutral axis for the above-cross section.

Q: 3. Bars AB, CD, and EF cach have a cross-sectional area of 25 mm and modulus of clasticity E=200…

A:

Q: Determine the maximum weight of the lamp that the cables shown in figure can support. The stresses…

A:

Q: An element in plane stress from the fuselage of an airplane is subjected to compressive stresses of…

A: To find: The σy1 acting on an element oriented at a clockwise angle of 40° from the horizontal.…

Q: O1: Two steel pipes [E =200 GPa], each with a cross- sectional area of 1475 mm', are attached to…

A: GIVEN DATA AREA A=1475 mm2 E=200GPa LOAD=120KN WE HAVE TO FIND STRESS IN BOTH PIPES

Q: A circular bracket with a diameter of 100 mm is fixed to a wall as shown in the figure below.…

A:

Q: A circular bracket with a diameter of 100 mm is fixed to a wall as shown in the figure. Determine…

A:

Q: 1. A rod is composed of three segments as shown in the figure and carries the axial loads P1= 120kN…

A:

Q: 5: An aluminum rod (E-70 GPa and v=0.25) is inserted into a hollow steel tube (E=210 Gra and…

A: Given data:-  P= 200KN D=40 mm Di =50 mm t = 10 mm

Q: The pinned members shown in figure carry the loads P and 2P. All bars have cross-sectional area A.…

A:

Q: A uniform bar AB weighing 500 kg is supported at both end by a cable as shown in the figure.…

A:

Q: For the assembly, find the stress in each rod if the temperature rises 30°C after a load W 120 kN is…

A:

Q: Q8(0: For the truss shown in the Figure, if the diameter of pins at A and G are 3 in and 2 in,…

A: Given: dA = 3 in. dG = 2 in.   To find: shear stress in pins A and G. Stresses in the members AG,…

Q: 5. Segment AB of the bar is a tube with an outer diameter of d1 and a wall thickness of 0.125 in.…

A: Given   Allowable stress in rod AB = 3400 psi   Outer diameter = d1   Inner diameter = d1 - 0.125…

Q: The round bar ABD of 12 mm diameter is fixed to the wall at its left end and has two arms BE and DC…

A: Diameter of bar = 12 mm. It has two arms at a distance of 55 mm and 95 mm from fixed end Arm length…

Q: Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1)…

A:

Q: A three-member plane truss is shown in the figure. Member (2) has a cross section of 400 mm? and is…

A: Given: Member 2 is made of steel and its specification are  A=400 mm2 ,E=210 GPa. While for member 1…

Q: 3. A cylinder with one closed end and one free end has an outer radius, b =260mm, and an inner…

A: solutionwe have given in the question.outer radius (r0)=260mminner radius (ri)=55mminterval pressure…

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.