The foundation bolt is shown in the below figure a force F = 300 N. The bolt material is wire of diameter d = 6 mm to a radius R= 10 mm in the eye and at the shank. Determine the stresses at the inner and outer surfaces at section A-A.

The foundation bolt is shown in the below figure a force F = 300 N. The bolt material is wire of diameter d = 6 mm to a radius R= 10 mm in the eye and at the shank. Determine the stresses at the inner and outer surfaces at section A-A.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.12.11P: A cylindrical brick chimney of height H weighs w = 825 lb/ft of height (see figure). The inner and...

See similar textbooks

Related questions

Q: The stresses acting on element A in the web of atrain rail are found to be 40 MPa tension in the…

A: Given Stress = 40 MPa tension = 160 MPa compression Shear stress = 54 MPa Find…

Q: Q2) For the problem shown in the figure, - Find the axial displacement at the end B - Determine the…

A: for solution refer below images.

Q: Find the stresses at points A andB on the plate shown in the figure.

A: The normal stress at the points A and B can be determined as,

Q: The flat bars shown in parts a and b of the figure are subjected to tensile forces P-3.0 kips. Each…

A: Given data, Tensile force P=3.0 Kips Thickness t=0.3 in.a For the bar with a…

Q: A steel pipe with an outside diameter of 4.13 in. and an inside diameter of 3.69 in. supports the…

Q: The box beam shown in Figure P8.63b has dimensions of b=80mm, d=120mm, and t=8mm. A downward…

Q: roblems In the figure shown, determine the diameter of the rod C if the allowable stress 86.60 MPa.…

A: Givenallowable stress of rod σa=86.60MPaallowable shear stress on pin A=60MPadouble shear stress

Q: F1. The rigid bar ABC in the figure is supported by a clevis and pin at its right hand side and by…

A: Draw the free-body diagram of the beam.

Q: The young modulus of the bar, which is made of St70 steel material shown in the figure, is 210GP..…

A: Given data as per the question Young modulus of the bar =210 Gpa cross section of the bar=500…

Q: The hollow drill pipe for an oil well (see figure)is 6.2 in. in outer diameter and 0.75 in. in…

A: Given Outer diameter = 6.2 in Thickness = 0.75 in Weight = 62 kips Torque = 185 kip-in To find…

Q: 3. A 65 mm diameter solid shaft is subjected to force and torque as shown in the figure below.…

A: Given, Diameter, D=65 mm,Cross-section Area, A=π4D2A=π4652A=3318.307 mm2 Calculate the stress due to…

Q: Problem 6 For the structure shown in the figure, determine the normal and shear stresses at point A…

A: Given data: Vz=6 kN Need to determine the normal and shear stresses at point A on the cross section…

Q: The structure of hook is made such that it is in round shape with diameter d= 20mm as shown in the…

Q: Q.3) For the shaft consist of two parts shown in figure. If shaft (1) has outside diameter doutl =…

Q: For the clamp C shown in the figure, determine the maximum clamping force P if the normal tension…

A: Introduction: Clamping force is the amount of force imparted to a workpiece by closing and locking a…

Q: 1. In the figure shown, determine the diameter of the rod C if the allowable stress 86.60 MPa.…

A: Solution of Question 2

Q: S A- Sección 4-a 1200 N B 1500 N 1000 N

Q: A 100mm diameter steel shaft is loaded as indicated in the figure. Determine the angle of twist of…

A: find angle of twist of pulley D with respect to A and shear stress in each section.

Q: The cantilevered tube shown in the following figure is to be made of 2014 aluminum alloy and is…

A: The tube is subjected to axial loading, bending, and torsion simultaneously, thus there will be…

Q: In the figure, a force of 1 kN is applied by means of an arm connected to a shaft with a diameter of…

A: Now, calculate the torque due to 1 kN force, T = 100 x 1 kN = 100 kN-m Bending moment due to 1 kN, M…

Q: Determine the maximum axial force P that can be applied to the bar in the figure below. The bar is…

Q: Figure Problem In the figure shown, determine the stress in the cable C if its area is 600 mm?.…

Q: A thick-walled cylinder with internal and external radii 86 mm and 166 mm respectively, is subject…

A: we have to determine the radial and hoop stress

Q: A steel pipe with an outside diameter of 4.67 in. and an inside diameter of 4.25 in. supports the…

Q: A circular bracket with a diameter of 100 mm is fixed to a wall as shown in the figure below.…

Q: The machine component shown in Figure below is subjected to a load P = 450 lb that acts at an angle…

Q: 4- The cross-section of the ABCD element in the figure is a circle with a diameter of 6 cm. The…

Q: 7.4-17 A sign is supported by a pole of hollow circular cross section, as shown in the figure. The…

A: Given: The outer diameter of pole, D = 10.5 in The inner diameter of pole, d = 8.5 in The height of…

Q: A vertical shaft is supported by a thrust collar and bearing plate, as shown in Figure. Calculate…

A: given: Dc=150mm Ds=100mm σ=100MPa Maximum axial load between the collar and plate. P=σ×A…

Q: A simply supported wood beam is subjected to uniformly distributed load q. The width of the beam is…

A: We have to first find out the shear force and bending moment at point C. Then, the normal stresses…

Q: 5 KN / m A SIMPLE STRESSES 5 KN / m D 50 KN-m 5 KN / m F E 2. Points C and D of the 1.00 1.00 1.00…

Q: The horizontal pipe shown in Figure 2 has a hollow circular cross section of 38mm inner- diameter…

Q: Q5(): For the truss shown in the Figure, if the diameter of pins at A and F are 2 in. and 1.5 in.,…

Q: Problem C-2 [Average Normal and Average Shear Stresses] A structure is under an external loading of…

A: To normal and average stress at section aa

Q: For the beam and loading shown in the figure below, determine: 1- The normal and shearing stresses…

A: Part 1 From fig we can say that the forces that play a vital role to form normal and shear stress…

Q: D16. For the truss shown in figure determine the displacements at point B and stresses in the bars…

A: To determine the stresses in Part AB and BC.

Q: A vertical shaft is supported by a thrust collar and bearing plate, as shown in Figure. Calculate…

Q: A circular bracket with a diameter of 100 mm is fixed to a wall as shown in the figure. Determine…

Q: For the plane trusses shown in Figure P3-30, determine the horizontal and vertical displacements of…

Q: In the crank arm of the figure, two loads P act as shown: one parallel to the x axis and another…

A: (a) Draw the given diagram with support reactions, Now, apply force equilibrium in x-direction,…

Q: For the structure shown in the figure, calculate the size of the bolt and area of the bear- 1-18.…

Q: An element in plane stress from the fuselage of an airplane is subjected to compressive stresses of…

A: To find: The σy1 acting on an element oriented at a clockwise angle of 40° from the horizontal.…

Q: A thick-walled cylinder with closed ends has internal and external radii 100 mm and 180 mm…

A: For solution refer below images.

Q: A simple pin-connected truss is loaded and supported as shown in the figure. All members of the…

A: Given Data:-Outside Diameter=5.00 inThickness=0.274 inload, P=8 kips;Q=8 kips=a=4 ft, b=8 ft &…

Q: A pressure vessel of thickness 10 mm and inner radius 220 mm is subjected to an internal pressure of…

A: Mohr's circle is a graphical representation of plane stress. In this representation, the stresses in…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure.…

Q: PROBLEM 2. The carrier system in the figure consists of the AB rigid beam and two aluminum bars and…

A: Data given- Steel A- 36 A = 160 mm2 T2 = 80°C T1 = 20°C 2014- T6 Al A = 200 mm2

Q: Figure Problem In the figure shown, determine the stress in the cable C if its area is 600 mm².…

A: GivenAC=600mm2τaallowable=80MPa=80 N/mm2

Q: Q2) For the problem shown in the figure, - Find the axial displacement at the end B - Determine the…

A: Given data, E = Modulus of elasticity = 50 MPa d1 = Inner diameter at the smaller end = 40 mm d2 =…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

The foundation bolt is shown in the below figure a force F = 300 N. The bolt material is
wire of diameter d = 6 mm to a radius R = 10 mm in the eye and at the shank. Determine the
stresses at the inner and outer surfaces at section A-A.
FA B

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A cylindrical brick chimney of height H weighs w = 825 lb/ft of height (see figure). The inner and outer diameters are d1= 3 ft and d2= 4 ft, respectively. The wind pressure against the side of the chimney is p = 10 lb/ft2 of projected area. Determine the maximum height H if there is to be no tension in the brickwork.
A thin metal strip of total weight W and length L is placed across the top of a flat table of width L2as shown in the figure. What is the clearance S between the strip and the middle of the table? (The strip of metal has flexural rigidity EI.)
A large precast concrete panel for a warehouse is raised using two sets of cables at two lift lines, as shown in the figure part a. Cable 1 has a length L1 = 22 Ft, cable 2 has a length L2= 10 ft, and the distance along the panel between lift points Band D is d = 14 ft (see figure part b). The total weight of the panel is W = 85 kips. Assuming the cable lift Forces F at each lift line are about equal, use the simplified model of one half of the panel in figure part b to perform your analysis for the lift position shown. Find the required cross-sectional area AC of the cable if its breaking stress is 91 ksi and a factor of safety of 4 with respect to failure is desired.
A long re Lai nine: wall is braced by wood shores set at an angle of 30° and supported by concrete thrust blocks, as shown in the first part of the figure. The shores are evenly spaced at 3 m apart. For analysis purposes, the wall and shores are idealized as shown in the second part of the figure. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall is assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the walls is F = 190 kN. If each shore has a 150 mm X 150 mm square cross section, what is the compressive stress
A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the top of a vertical buttress AB (see figure). The vertical buttress has height h = 5.0 m and rectangular cross section of thickness t = 1.5 m and width b = 1.0 m (perpendicular to the plane of the figure). The stone used in the construction weighs y = 26 kN/m3. What is the required weight W of the pedestal and statue above the vertical buttress (that is, above section A) to avoid any tensile stresses in the vertical buttress?
The main cables of a suspension bridge (see figure part a) follow a curve that is nearly parabolic because the primary load on the cables is the weight of the bridge deck, which is uniform in intensity along the horizontal. Therefore, represent the central region AOB of one of the main cables (see part b of the figure) as a parabolic cable supported at points A and B and carrying a uniform load of intensity q along the horizontal. The span of the cable is L, the sag is /i, the axial rigidity is EA\ and the origin of coordinates is at mid span. (a) Derive the following formula for the elongation of cable AOB shown in part b or the figure: (b) Calculate the elongation 5 of the central span of one of the main cables of the Golden Gate Bridge for which the dimensions and properties are L = 4200 ft,h = 470 ft, q = 12,700 lb/ft, and E = 23,300,000 psi The cable consists of 27,572 parallel wires of diameter 0.196 in. Hint: Determine the tensile force Tal any point in the cable from a free-body diagram of part of the cable; then determine the elongation of an element of the cable of length ds: finally, integrate along the curve of the cable to obtain an equation for the elongation £.
A sign for an automobile service station is supported by two aluminum poles of hollow circular cross section, as shown in the figure. The poles are being designed to resist a wind pressure of 75 lb/ft" against the full area of the sign. The dimensions of the poles and sign are hx= 20 ft, /r =5 ft, and h = 10 ft. To prevent buckling of the walls of the poles, the thickness e is specified as one-tenth the outside diameter d. (a) Determine the minimum required diameter of the poles based upon an allowable bending stress of 7500 psi in the aluminum. (b) Determine the minimum required diameter based upon an allowable shear stress of 300 psi.
A cylinder filled with oil is under pressure from a piston, as shown in the figure. The diameter d of the piston is 1,80 in. and the compressive force F is 3500 lb. The maximum allowable shear stress t^^, in the wall of the cylinder is 5500 psi. What is the minimum permissible thickness t„± of the cylinder wall? (Sec figure
Determine the shape factor f for a cross section in the shape of a double trapezoid having the dimensions shown in the figure. Also, check your result for the special cases of a rhombus (b1= 0) and a rectangle (b1= b2).
An L-shaped reinforced concrete slab 12 Ft X 12 ft, with a 6 Ft X 6 ft cut-out and thickness t = 9.0 in, is lifted by three cables attached at O, B, and D, as shown in the figure. The cables are are combined at point Q, which is 7.0 Ft above the top of the slab and directly above the center of mass at C. Each cable has an effective cross-sectional area of Ae= 0.12 in2. (a) Find the tensile force Tr(i = 1, 2, 3) in each cable due to the weight W of the concrete slab (ignore weight of cables). (b) Find the average stress ov in each cable. (See Table I-1 in Appendix I for the weight density of reinforced concrete.) (c) Add cable AQ so that OQA is one continuous cable, with each segment having Force T, which is connected to cables BQ and DQ at point Q. Repeat parts (a) and (b). Hini: There are now three Forced equilibrium equations and one constrain equation, T1= T4.
The figure shows an idealized structure consisting of rigid bars ABC And DEF joined by a linearly elastic spring ß between C and D. The structure is also supported by translational elastic support ß at B and rotational elastic support ßRat E. Determine the critical load Pcrfor the structure.
The bearings at A and D exert only y and z components of force on the shaft as shown in Fig 7. Determine the smallest diameter of the shaft using maximum shear stress hypothesis theory if the allowable stress is 100 MPa.