A circular tube is subjected to torsion by torques T applied at the ends. The bar is 0.5m. long and the inside and outside diameters are 30mm and 40mm respectively. It is determined by measurement that the angle of twist is 3.600 when the torque is 650 N.m. a. Calculate the maximum shear stress in the tube. b. Calculate the shear modulus of elasticity. c. Calculate the maximum shear strain in radians.

A circular tube is subjected to torsion by torques T applied at the ends. The bar is 0.5m. long and the inside and outside diameters are 30mm and 40mm respectively. It is determined by measurement that the angle of twist is 3.600 when the torque is 650 N.m. a. Calculate the maximum shear stress in the tube. b. Calculate the shear modulus of elasticity. c. Calculate the maximum shear strain in radians.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.11.5P: A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used...

See similar textbooks

Similar questions

The constant wall thickness of a tube with the elliptical cross section shown is 0.12 in. what torque will cause a shear stress of 6000psi?
A flange-and-bolt coupling between two shafts carries 12 bolts at a pitch diameter of 18 in. The shafts carry a torque of 50,000 ft-lb. Assuming that this torque is transmitted by shear across the 12 bolts and that these bolts are to be designed for a shear stress s3 = 3,000 lb/sq in., what is the bolt diameter?
Find the max shear stress in given data of two circular shafts (S) AND (H)
A uniform shaft of diameter 30 mm is subject to a 60 N of tangential force. Calculate the shear stress induced in the shaft.
A 4-spline shaft and to slide when not under load has a diameter of 2.5 in. Find the compressive and shear stresses if shearing force is 2500 lbs. If hub length is 2 inches.
A commercial steel supplier lists rectangular steel tubing having outside dimensions of 4.00 by 2.00 in and a wall thickness of 0.109 in. Compute the maximum torque that can be applied to such a tube if the shear stress is to be limited to 6000 psi. For this torque, compute the angle of twist of the tube over a length of 6.5 ft.
A) Define the following terms; I)A propeller shaft for a small machine is made of a solid steel bar 104mm in diameter.The allowable stress in shear is 48MPa, and the allowable rate of twist is 2.0° in 3.5meters.Assuming that the shear modulus of elasticity is G=80GPa, calculate the maximum torque that can be applied to the shaft.
A square steel bar, 25 mm on a side and 650 mm long,is subjected to a torque of 230 N #m. Compute the shear stress and the angle of twist for the bar.
A circular tube of aluminum is subjected to torsion by torques T applied at both end. The bar 0.5m long and the inside and outside diameters are 30mm and 40mm, respectively. It is determined by measurements that the angele of twists is 3.57 degree when the torque is 600N-m. Calculate the maximum shear stress in the tube. Calculate the shear modulus of elasticity
Consider the 1inch steel square tube loaded in torsion.the tube has wall thickness of 0.0196 inch and length is 40 inches and maximum allowable shear stress is 7.2 kpsi determine maximum torque that could be applied and corresponding angle of the twist.
A circular tube is subjected to torque Tat its ends. The resultingmaximum shear strain in the tube is 0.005. Calculate the minimum shearstrain in the tube and the shear strain at the median line of the tubesection.
A full circular cross-section shaft will be designed to provide power transmission at 220 (revolution/minute) revolution of a 12300 kW engine. Since the shaft length is 3 m, the material shear modulus is 80 GPa, and the shear yield stress is 190 MPaa) How many kN.m torque should the shaft carry?b) Write down the minimum safe shaft radius in metersc) How many rad is the shaft at the specified minimum radius. found?