A cylindrical steel alloy rod with a 0.5 in. diameter is subjected to tension.Determine the magnitude of the load required to produce a 10-4 in. change in diameter if the deformation is entirely elastic. Assume a Young’s modulus of 30 * 106 psi and a Poisson’s ratio of 0.27.

A cylindrical steel alloy rod with a 0.5 in. diameter is subjected to tension.Determine the magnitude of the load required to produce a 10-4 in. change in diameter if the deformation is entirely elastic. Assume a Young’s modulus of 30 * 106 psi and a Poisson’s ratio of 0.27.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Related questions

Q: 10. As shown in the figure, there is a gap between the aluminum bar and the rigid slab that is…

A: We have to determine the value of the stress in each rod when the temperature in the assembly is…

Q: SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and…

Q: A 3000 kgf tensile load is applied on a steel bar of 3.25 cm diameter. When the same load is applied…

A: Given data: P=3000 kgfDsteel=3.25 cmEsteel=2.1×106 kgf/cm2Eal=0.7×106 kgf/cm2

Q: Determine the value of load P if At = 30 °C and the stress in bronze is limited to 132 MPa. Aluminum…

Q: a bar is 500mm long and is stretched to 505 mm with a force of 50kn.the bar is 10mm diameter.…

A: Given data : Initial length=500 mmFinal length=505 mmForce (F)=50 KNDiameter (D)=10 mm

Q: The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor…

Q: 200 3 kg/m Al. 3280mm 350 sk|| 160 mm 80 mm Find maximum stresses in steel and aluminum

A: Given:- A composite beam made of steel and aluminum is given The magnitude of the load on beam = 3…

Q: A 2-m long steel rod, 10-mm in diameter, is carrying a load of 20 kN. (a) what is the axial stress…

A: This question is related to the Strength of material. In this question we calculate axial stress and…

Q: Given that a steel cyInder of dimenslons 12.0 mm in dlameter and 70 mm bng is subjected to tensicn.…

A: a) According to Hook's law within the elastic limit, stress is directly proportional to strain.…

Q: An aluminum bar having a cross-sectional area of 160 mm2 carries the axial loads as shown in the…

Q: a. A round steel bar with an initial diameter of 20 mm and length of 2 m is placed in tension,…

Q: A bar is 500 mm long and is stretched to 505 mm with a force of 50 kN. The bar is 10 mm diameter.…

A: Stress- It can be defined as the force acting per unit area, and given by σ=PA Strain- it is defined…

Q: 1. A hollow steel column is subjected to a load of 180-KN, determine the change in length if the…

Q: A steel bar of length 30 m and having specific weight of 20 x 10-5 N/mm³. Find the elongation of the…

Q: 7. Using the value obtained in the previous problem, which of the following most nearly gives the…

Q: A thin square plate is uniformly deformed as shown in the figure. Assume a - 100 mm, b-15 mm, c-85…

A: Given Data:Assume a=100mmb=15mmc=85mmand d=115mm

Q: 1. A nylon string has a diameter of 2 mm, pulled by a force of 100 N. Determine the stress.

A: GIVEN : diameter of a nylon string D is 2mm force acting on nylon string F is 100 N we have to…

Q: A 220 mm? steel rod and 420 mm? copper rod supports a rigid bar as shown. If a 30 kN load is…

Q: 1) A circular aluminum tube of length L = 400 mm is loaded in compression by forces P (see figure).…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: Q2\ A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in…

A: When the deviation exceeds the maximum allowable value, the amount of radiation obtained on the…

Q: An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads as shown in the…

Q: A wood beam carries the loading shown in the figure. Determine the smallest allowable width b of the…

A: given- working stress σ=10 MPacross section area A=200 mm×b mmwhere,b=smallest allowable width To…

Q: of the bronze bar and the rigid slab supported by two steel bars as shown. Neglecting the mass of…

A: In such assembly, the free stress will develop when, The free expansion in bronze > free…

Q: A wood beam carries the loading shown in the figure. Determine the smallest allowable width b of the…

Q: Problem 13.1. The aluminum machine part is subjected to a moment of M = 75 N.m. Determine the…

A: M=75 N-marea of the flangeA1=10×40A1=400 mm2distance of centroid of the flange from…

Q: A 50 mm X 80 mm rectangular steel plate subjected to the uniaxial stress condition is shown in the…

A: Given data Stress in x direction (σx) = 200 MPa E = 200 GPa μ = 0.3

Q: Problem 3: Diameter of the metal bar, before and after load application was measured to be 100.00 mm…

Q: 9. A 200 kgf load is applied to a steel bar of cross section area 6 cm?. When the same load is…

Q: A wood beam carries the loading shown in the figure. Determine the smallest allowable width b of the…

A: Ultimate stress is the safest stress taken within elastic limit. It is the ratio of ultimate stress…

Q: A steel rectangular block 1in wide, 1/2in deep and 4in long is subjected to an axial tensile load of…

A: b = 1in wide d = 1/2in deep L = 4in P = ∆L = 2.8×10-2in∆b = .21×10-2in

Q: An arbitrary material has an elastic modulus of 118 GPa. How much tensile force was applied to a 100…

A: we have E = 118Gpa 100 mm long cylinder with 10 mm dia and redution in area = 0.1 % and poissons…

Q: Determine the modulus of Elasticity E for a material that has proportional stress of 100 MPa and…

A: Given Proportional stress = 100 Mpa Proportional strain = 0.001 To find Modulus of Elasticity (E)

Q: 1. A steel bar is subjected to the loads shown in the figure. Determine the total deformation in the…

A: When the material like steel bar or another object is under tension or compression the change in…

Q: If a steel column with cross-sectional area A = 1000 mm^2 modulus of elasticity E = 200 MPa and…

Q: Figure shown is a bar composed of different materials - Aluminum and Steel attached to rigid…

Q: A copper rod with a diameter of 19 mm, modulus of 110 GPa, and a Poisson’sratio of 0.35 is subjected…

A: Given: The diameter of copper d, is 19 mm. Poisson’s ratio is 0.35. The reduction is diameter is…

Q: A steel wire with a diameter of d is bent around a cylindrical drum with a radius of R = 0.9 m. What…

A: The bending stress is σb=690 MPa. The modulus of elasticity is E=210 GPa. The radius is R=0.9 m.

Q: Q1\ A copper bar consists from three sections: sections 1 is of 25 mm diameter and 60 mm long,…

A: Given for smallest cross-section,σ2=20 MN/m2=20×106 N/m2We know that, σ2=PA2So, P=…

Q: A wood beam carries the loading shown in the figure. Determine the smallest allowable width b of the…

A: Given- a beam carrying UDL and UVL load system Required- To find out the smallest allowable width of…

Q: Find the bulk modulus of elasticity of a liquid of pressure 150 psi applied to 10 ft^3 of the liquid…

Q: PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the…

Q: An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads as shown in the…

Q: A specimen of ductile cast iron having a rectangular cross section of dimensions 4.8 mm x 15.9 mm is…

A: Modulus of elasticity can be defined as the ratio of the stress experienced by a body or in a body…

Q: Problem 6 Diameter of the metal bar, before and after load application was measured to be 100.00 mm…

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

Q: A1 m long steel rod with a cross-section of 20 mm x 20 mm is subjected to tensile force of 40 kN.…

A: Given data,

Q: Steel Bronze Area (mm) 600 300 3. Figure (a) shows a rigid bar that is supported by a pin at A and…

A: Given:- A rigid bar is supported by a pin at A and two rods One rod is made of steel and the other…

Q: An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads as shown in the…

A: An arrangement of forces on Aluminium bar have been given and it has been asked to determine axial…

Q: Determine the total deformation of a tapered bar with a thickness (t = 25 mm) as shown in the…

Question

A cylindrical steel alloy rod with a 0.5 in. diameter is subjected to tension.Determine the magnitude of the load required to produce a 10^-4 in. change in diameter if the deformation is entirely elastic. Assume a Young’s modulus of 30 * 10⁶ psi and a Poisson’s ratio of 0.27.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 9 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
According to Figure 5-20, is ii possible to completely separate one of the four materials from the other three? Explain your answer.
A 10.0 mm diameter cylindrical specimen of a bearing bronze material is pulled under uniaxial tension with a force of 1500 N. The diameter of the bar reduces by 0.67 mm. Compute the modulus of elasticity for this material given that it’s Poisson’s ratio,n, is 0.35.
A closed right circular cylinder has radius 2 units and height 17 units A load of an unknown weight is put on top of the cylinder, causing the cylinder to shorten by 1.1 units. Find the new volume of cylinder due to this deformation in the height of the cylinder.
A 2-m long steel rod, 10-mm in diameter, is carrying a load of 20 kN. (a) what is the axial stress developed in the rod, in kN/m^2. Is the tensile or compressive? (b) compute the amount of elongation (in mm) in the steel rod caused by the applied load, (c) what will be the elongation (in mm) in the steel rod if the weight of the steel rod is included? Use density of the steel to be 7860 kg/m^3. Young's modulus of elasticity, E=200GPa. W=mg. Draw free body diagram of the steel rod.
Steel cylinder has 200 mm mean diameter with a wall 1 mm thick and 310 mm long. Determine the circumferential and longitudinal stresses that occur on the cylinder if the maximum pressure difference allowed between the inside and outside must not exceed 100 MPa. Determine the effects of three dimensional loading by determine volumetric strain and change in volume for the first steel cylinder. Modulus of elasticity E= (210 GPa), Poisson's ratio 0.30. 7
A compressive load of 50 KN is applied 150 on the axis of a steel-round bar of 8 mm diameter. Compute its stress and strain if the given modulus of elasticity is 75 GPa. Please draw a figure.
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value P if the change in length of the bar is limited to 2 mm and the working stresses prescribed in the table are not to be exceeded
Calculate the plane stresses involved where two pieces of steel are welded together. Our sign convention defines forces causing the object to be in tension positive and forces causing the object to be in compression negative. As we can see from the picture our σx = −4.5MPa and σy = 10MPa. Steel has an average Young’s modulus of elasticity of E = 200 GPa and an average Poisson’s ratio of ν = .285 Because it is not defined we will assume that initially there is no shear stress, τxy = 0. Solve only for: Compression in the x-direction(deformation along the weld)=(-Blank 4)? x 10^-5