A DDS synthesizer has a 150-MHz clock and a constant value of 15. The ROM address register has 14 bits. What is the output frequency?
Q: For a FM system, the maximum freq deviation is 75 kHz and the maximum freq of the info. signal is 10…
A: According to Carson's formula, the bandwidth (B) of a frequency modulated system can be expressed as
Q: What is the name given to the process of frequency modulation of a carrier by binary data? Binary…
A: Name given to the process of frequency modulation of a carrier by binary data. This is related to…
Q: Decoder circuit as shown in the following Figure. if A is LSB and C is MSB, the output expression F=
A:
Q: Implement the following function with an 8 to 1 multiplexer. Remember, you are not required to…
A:
Q: Home Work If the enable pulse frequency in Figure below were halved, determine the binary numbers…
A: Given waveform: To find: If the enable pulses frequency was halved, determine the binary numbers…
Q: For a PCM system with the following parameters, Parameters: (i) Maximum analog input frequency = 5…
A:
Q: H.W: Compute the binary code word values for the amplitudes 0.4 V and 0.78 V, then compute the…
A:
Q: Q1. A PCM encoder using A-law has a dynamic range of +2 V. Determine the code word when the input…
A: (a) -120 mV (b) 0.5mV (c) -1.5 V (d) 1.8V PCM encoder using A -law of +2V code word (a) 0110 1001…
Q: Q3:/ consider the following analog waveform. This waveform is sampled at a 500 Hz rate and quantized…
A: First find out the quantization level in above question and then find out the sampling points :-…
Q: ii) We want to digitise a signal that contains frequencies between 100 Hz and 1500 Hz, assuming 16…
A: Bits rate are number of bit transmit over the medium per second . Bit rate is calculated by : bit…
Q: Q1. Design asynchronous (ripple ) binary counter and timing diagram for the following sequence…
A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…
Q: Why is the Nyquist sampling theorem important in analogue to digital conversion? It defines the…
A:
Q: Q3/ Twenty-four voice signals are sampled uniformly and then have to be time division multiplexed.…
A: We need to find out bandwidth and sampling rate for given signal
Q: Q5/ The information in an analog waveform with maximum frequency fm = 3 KHz is to be transmitted…
A:
Q: A PCM system has the following parameters: a maximum analog input frequency of 4.5kHz, a maximum…
A:
Q: Q5: An analog signal is first encoded in binary PCM before being transformed to a multilevel signal…
A: It is given that: fm=2700 HzL=7Accuracy=p=1 %=0.01
Q: For a CD audio system, the analog signal is digitized such that the signal to quantization ratio is…
A: Given data: Signal to quantization noise ratio SNQ≥96 dB Sampling frequency fs=44100 Hz
Q: Create the gray code representation of the following binary numbers. i) 01011 ii) 10110 iii) 01101…
A: Here all the questions are from different topics. So we are bound to solve only one. Please ask the…
Q: Example 1.3: A digital optical disc (CD) storage records video signals digitally by using PCM.…
A:
Q: 1- Explain the operation of the PCM encoder used in module ED-2960F. 2- Discuss the advantages and…
A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…
Q: What will be the BCD equivalent of decimal 15?
A:
Q: Using a ROM, implement a 1-digit binary to 7-segment display decoder. In vhdl programming language.
A: Implement a 1-digit binary to 7-segment display decoder in VHDL programming language. The boolean…
Q: A 1000-bit signal passes through a digital system. It is said that the signal was transmitted over…
A: 1000 bits are transferred through this channel in 2.1u sec Now bits transferred in 1 sec is called…
Q: are specifications of Digital modulation techniques?
A: Digital Modulation Techniques. It is the kind of process in which encode a digital information…
Q: Determine (a) the bit rate and (b) the resolution in the sampling of a seismic signal with dynamic…
A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…
Q: What hex value do you need to put in the Pullup resistor register in order to initialize the GPIO…
A: In the GPIO port, the output ports are both writable and readable, while input ports are only…
Q: Q3/ Twenty-four voice signals are sampled uniformly and then have to be time division multiplexed.…
A: We need to find out the bandwidth and sampling frequency for given system .
Q: A given signal [V(t)=sin(20Nt) volts] is to be sampled at 100 samples/s, what will be the encoded…
A: Given, Signal is V(t) = sin(20πt) Volts Sampling rate(fs) = 100 samples/s Dynamic range (DR) =…
Q: Create an 8086 Assembly language program that subtracts two 8-bit ASCII numbers, the first and…
A: First we will initialize the data segments. then move the data from the address 200 and 400 to AL…
Q: Discussion: 1. State some applications of PSK modulation. 2. What are the advantages and…
A: Phase Shift Keying (PSK)- It is the digital modulation technique in which the phase of the carrier…
Q: Q4/ A PCM system uses a uniform quantizer followed by a 7-bits binary encoder. The bit rate of the…
A:
Q: How to measure the quality of the output signal in ADC? A. Signal-to-noise ratio B. Quantization…
A: The Signal to quantization noise ratio reflects the relationship between the maximum nominal signal…
Q: In a PCM system, the maximum frequency of the analog input signal is 4 kHz. If the number of…
A: Given that Maximum frequency of the analog input signal (fm) = 4 kHz Quantization level=2 =2n So…
Q: The information in an analog waveform, whose maximum frequency fm34000Hz, is to be transmitted using…
A:
Q: A digital computer has a common bus system for 16 registers of 32 bits each. The bus is constructed…
A: Given that Number of registers 16 Size of each register 32 bit Number of register =16 (A) No of…
Q: The information in an analog waveform, whose maximum frequency fm-4000Hz, is to be transmitted using…
A:
Q: For a PCM system with the following parameters, Parameters: (i) Maximum analog input frequency = 5…
A: It is given that: fm=5kHzDynamic range=54dBVmax=±5.01V
Q: How is the output frequency of a frequency of a PLL synthesizer changed?
A: Frequency synthesizer is defined as it is a electronic circuit which generates variable frequency to…
Q: 4000 Hz, what sampling rate should be used to retain all necessary information in the digital data?…
A:
Q: (7) An analog signal with a bandwidth of 4.2kHz is to be converted into binary PCM and transmitted…
A:
Q: what is Successive approximation ADC? please explain
A: Here is block diagram of SAR. It uses Bisection method to keep or alter the bit for set or reset.…
Q: Q6: Binary channel with bitrate R,=36000 bits/sec is available for PCM voice transmission. Find…
A: "Since you have asked multiple question , we will solve the first question for you if you want any…
Q: A) setup a scheme for accomplishing this multiplexing requirement B) what must be the speed of the…
A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…
Q: Compare the maximum conversion times of a 8-bit digital-ram p ADC and a 8-bit successive-…
A:
Q: Q1. Design asynchronous (ripple ) binary counter and timing diagram for the following sequence…
A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…
Q: How to represent a priority encoder by using truth table and draw a diagram
A: The binary encoder is used to compress a large number of the inputs to a smaller output. For…
Q: Q7/ Given an audio signal consisting of sinusoidal term given as x(t) = 3 cos(500nt) %3D Determine…
A:
Q: Find the number of bits given if the PCM system has a quantization error of 0.4 V and maximum input…
A: Given: Quantization error = 0.4 V Maximum input = 6V
A DDS synthesizer has a 150-MHz clock and a constant value of 15. The ROM address register has 14 bits. What is the output frequency?
Step by step
Solved in 2 steps with 2 images
- A PCM system has the following parameters: a maximum analog input frequency of 4.5kHz, a maximum decoded voltage at the reciever of +-5V, and a minimum dynamic range of 60dB. Determine the following c) actual number of bits used in the PCM code (excluding the sign).Microprocessors Write a program for the 8051 to transfer “YES” serially at 9600 baud, 8-bit data, 1 stop bit, do this continuouslyA voice frequency channel, a signal voltage is 40mV and noise voltage is 40fV.What is the maximum data rate that can be transmitted if parameter resistances are equal?
- Explain the output response of a second order system.Compare the maximum conversion times of a 8-bit digital-ram p ADC and a 8-bit successive- approximation ADC if both utilize a 500-KHz and .l .5 MHz clock frequency.A 10-bit 5-V ADC operates with a sampling frequency of 1 MHz. If a linear histogram test is to be conducted on this ADC with a ramp signal of 15-ms duration, estimate the voltage resolution of this test.
- Electrical Engineering - Digital signal Processing EENG420 Please solve the question quickly ??What is the total capacity in hexadecimal representation for any segment base address wtihin the 8086 microprocessor's real address mode RAM?-FEFFh-BHAFh-FFFFh-EEEEhExplain the program memory structure of 8051 microcontroller. Write an ALP using 8085 online simulator tool to perform logical XOR operation for two 8 bit data. Load the accumulator with 34 H and load the B register with 1AH.
- Draw a schematic to interface a 15-key matrix keyboard using port C of the 8255A. Write instructions to initialize the port. (Microprocessor Subject)Design a system called a parallel binary comparator, that compares the 4 – bit binary string A to the 4 – bit binary string B. If the strings are exactly equal, provide a HIGH – level output to drive a warning buzzer.Write an 8088/8086 assembly program that counts the length of a null terminated string that starts at location STR.print The result on the screen Assume string length will not exceed 255 character.