A helicopter's rotor shaft has the hollow circular cross section shown as follows. The shaft is subjected to an axial load P = 34, 000N and a torque T = 600 N-m. Determine the principal stresses and the absolute maximum shear stress at a point p on the outer surface of the shaft. Draw the Mohr's circle of the stress state at point P. 34 mml+ T= 600 N-m 80 mm Cross section P = 34,000 N

A helicopter's rotor shaft has the hollow circular cross section shown as follows. The shaft is subjected to an axial load P = 34, 000N and a torque T = 600 N-m. Determine the principal stresses and the absolute maximum shear stress at a point p on the outer surface of the shaft. Draw the Mohr's circle of the stress state at point P. 34 mml+ T= 600 N-m 80 mm Cross section P = 34,000 N

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.6.9P: A prismatic bar with a length L = 3 ft and cross-sectional area A = 8 in2 is compressed by an axial...

See similar textbooks

Similar questions

A fire extinguisher tank is designed for an internal pressure of 825 psi. The tank has an outer diameter of 4.5 in. and thickness of O.OS in. Calculate the longitudinal stress, the circumferential stress, and the maximum shear stresses (out-of-plane and in-plane) at the outer surface of the tank.
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
Solve the preceding problem if the norm al and shear stresses acting on the element are sx = 2100 kPa, sy= 300 kPa, and txy= -560 kPa, and the seam is oriented at an angle of 22.5° to the clement.
A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind the maximum shear stress on the clement and show the state of stress on a sketch of a properly oriented clement.
A prismatic bar with a length L = 3 ft and cross-sectional area A = 8 in2 is compressed by an axial centroidal load P = 10 kips. Determine the complete state of stress acting on an inclined section pq that is cut through the bar at an angle W = 35", and show the stresses on a properly oriented stress element.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A circular pole is subjected to linearly varying distributed force with maximum intensity t0. Calculate the diameter daof the pole if the maximum allowable shear stress for the pole is 75 M Pa.
The concrete post (Ec = 3.6 × 106 psi and αc = 5.5 × 10-6/°F) is reinforced with six steel bars, each of 78-in.78-in. diameter (Es = 29 × 106 psi and αs = 6.5 × 10-6/°F). Determine the normal stresses induced in the steel and in the concrete by a temperature rise of 75°F.
Determine the average normal stress developed at points A, B, and C. The diameter ofeach segment is indicated in the Figure below.
A steel pipe with an outer diameter of 50 mm and a wall thickness of 5 mm is subjected to aninternal pressure of 10 MPa and an axial load of 20 kN at an angle of 45 degrees to the axis of thepipe. Determine the maximum axial stress and maximum hoop stress developed in the pipe.
A body is subjected to a direct tensile stress of 300 MPa in one plane accompained by a simple shear stress of 200 MPa. Determine maximum normal stress on the plane.