350 mm, tw = 7 mm, and h = 117 mm. Determine the principal stresses and the maximum shear stress acting at pc Show these stresses on an appropriate sketch. Xx d. D. (1) E 45° B xr Part 1 Determine the magnitude of the internal normal force, the internal shear force and the internal bending moment at Answer:

350 mm, tw = 7 mm, and h = 117 mm. Determine the principal stresses and the maximum shear stress acting at pc Show these stresses on an appropriate sketch. Xx d. D. (1) E 45° B xr Part 1 Determine the magnitude of the internal normal force, the internal shear force and the internal bending moment at Answer:

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.9.30P

See similar textbooks

Similar questions

A sign for an automobile service station is supported by two aluminum poles of hollow circular cross section, as shown in the figure. The poles are being designed to resist a wind pressure of 75 lb/ft" against the full area of the sign. The dimensions of the poles and sign are hx= 20 ft, /r =5 ft, and h = 10 ft. To prevent buckling of the walls of the poles, the thickness e is specified as one-tenth the outside diameter d. (a) Determine the minimum required diameter of the poles based upon an allowable bending stress of 7500 psi in the aluminum. (b) Determine the minimum required diameter based upon an allowable shear stress of 300 psi.
A sign for an automobile service station is supported by two aluminum poles of hollow circular cross section, as shown in the figure. The poles are being designed to resist a wind pressure of 70 lb/ft^2 against the full area of the sign. The dimensions of the poles and sign are h1 = 16 ft, h2 = 7 ft, and b = 13 ft. To prevent buckling of the walls of the poles, the thickness t is specified as one tenth the outside diameter d. (a) Determine the minimum required diameter of the poles based upon an allowable bending stress of 7100 psi in the aluminum. Round your answer to two decimal places. d = ___ in. (b) Determine the minimum required diameter based upon an allowable shear stress of 2100 psi. Round your answer to two decimal places. d = ___ in.
just final answer A rigid component ABC is supported by a pin-connected member (1). The member has a rectangular cross-section with dimensions of 54 mm and 48 mm. The elasticity modulus of the material is 169 GPa. If L1=2421 mm, L2=1226 mm, L3=2272 mm, and L4=2072 mm; Determine the maximum normal stress (MPa) in member (1) without buckling.
A straight and piecewise uniform bar ABCD of total length L is in Case 1 fixed at A in case 1 and in Case 2 fixed at both ends A and D. AB = BC = CD = L/3. The cross section area of segment CD is half of the area of the segment ABC, i.e. AABC = 2ACB. A point load of P is applied at B. Assume that bar material is linear and elastic and the modulus of elasticity is E.
Two members AB and AC are made of material with E= 138 Gpa and each member has cross sectional area of A= 346 mm2. The members are used to support bar BC. If P=1917 N, L1= 242 mm , L2= 373 mm and L3= 459 mm . Answer the following questions. The tension in member AB? The tension in member CD? The elongation in member AB? The elongation in member CD? Vertical displacement of point E?
A spreader bar is used in the assembly shown in the figure attached. It is made of a circular steel ros of diameter 32mm. Assuming that the cables and their connections are inextensible, determine largest load W that can be applied so that the spreader bar does not buckle. Both end of the spreader bar may be assumed to be pin connected. The youngs modulus of the spreader bar is, E = 200 x 10^3 N/mm^2.
Q#3. An aluminium strut 16 ft long has a rectangular cross section 2 in by 3.5 in. A bolt through each end secure the strut in such a way that is acts as hinged column about an axis perpendicular to 3.5 in dimension; and as fixed column about an axis perpendicular to 2 in dimension. Determine the safe central load with a factor of safety of 2 and E= 10300000 psi. Also discuss in detail about the governing column capacity and reasons behind it.
In the case of buckling: Determine the maximum concentrated vertical load P that can act on the top of the pillar of the figure. The load is applied at the centroid of the column cross section. Consider that the column is set at the top and base, and that the beams only act constraining the column displacement in the x-axis direction. The pillar can buckle in the two x and y directions. Use: E = 30 GPa, L = 5 m, b = 15 cm, h = 30 cm, σesc = 60 MPa
A wire 20 m long, weighing 0.8 N per m, and having a cross sectional area of 6.2 mm^2, is suspended vertically from its upper end, E = 103 GPa. Calculate the total elongation if a load of 220 N is attached to its lower end. A)9.22mm B)7.39mm C)6.89mm D)8.42mm
Polycarbonate bars (1) and (2) are attached at their lower ends to a slider block at B that travels vertically inside of a fixed smooth slot. Load P is applied to the slider block. Each bar has a cross-sectional area of 85 mm2, a lenght of 1.25 m, and an elastic modulus E = 8GPa. Use dimensions of a = 1.15 m and b = 0.90 m. For an applied load of P =1700 N, determine: (a) the forces in bars (1) and (2) (b) the defection at B of the slider block
A circular steel plate as shown in FIGURE H supported on 3 posts. A, B, C which are equally spaced along its circumference. A load P = 1350 N is at a distance x = 0.5 m from post at A along the diameter. Diameter of steel plate is 1.8 1. Reaction at post A a. 800 Nb. 900 Nc. 850 Nd. 950 N2. Reaction at post B a. 200 Nb. 250 Nc. 230 Nd. 280 N3. Reaction at C, considering the weight of the plate if it has a thickness of 16 mm and has a unit weight of 77 kN/m³ a. 1290 Nb. 1220 Nc. 1295 Nd. 1260 N
A straight girder of uniform section and length L rests on supports at the ends, and is propped up by a third support in the middle. The weight of the girder and its load is w per unit length. If the central support does not yield, prove that it takes a load equal to (5/8)wL. ANSWER: 1.80cm and 2.48cm Please show solution to the answer.