A large, open tank contains oil and is connected to a 0.3 cm diameter conduit as shown in Figure. A circular seal is used to seal the conduit. Determine (1) the magnitude of the friction force between the pipe wall and the seal. (2) the volume of oil flows across the pipe in 111 s after removal seal. (Pam - 100 kpa & pou 10° g/m) 30lcm 25 cm Water seal %3D

A large, open tank contains oil and is connected to a 0.3 cm diameter conduit as shown in Figure. A circular seal is used to seal the conduit. Determine (1) the magnitude of the friction force between the pipe wall and the seal. (2) the volume of oil flows across the pipe in 111 s after removal seal. (Pam - 100 kpa & pou 10° g/m) 30lcm 25 cm Water seal %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two vertical tanks, one with circular section 3.0 m in diameter, the other square section 1.33 m x 1.33 m are connected by a short tube ( area is 0.725 sq. cm) near bottom. Initially, the head of oil in the first tank is 4.0 m, while in the second tank the head is 60 cm. After a quick opening of the tube's vlave, find the time for the oil surfaces to equalize. Assume the tube properties to be similar to that orifice, with C= 0.78.CHOICES: a.26 seconds b.23 seconds c.21 seconds d.35 seconds
Two vertical tanks, one with circular section 3.0 m in diameter, the other square section 1.33 m x 1.33 m are connected by a short tube ( area is 0.725 sq. cm) near bottom. Initially, the head of oil in the first tank is 4.0 m, while in the second tank the head is 60 cm. After a quick opening of the tube's vlave, find the time for the oil surfaces to equalize. Assume the tube properties to be similar to that orifice, with C= 0.78.
Water from a reservoir is raised in a vertical tube of internal diameter D = 30 cm under the influence of the pulling force F of a piston. Determine the force needed to raise the water to a height of h = 1.5 m above the free surface. What would your response be for h = 3 m? Also, taking the atmospheric pressure to be 96 kPa, plot the absolute water pressure at the piston face as h varies from 0 to 3 m.
Consider an air solar collector that is 1 m wide and 5 m long and has a constant spacing of 3 cm between the glass cover and the collector plate as shown in Figure below, Air flows at an average temperature of 45°C at a rate of 0.15 m/s through the 1-m-wide edge of the collector along the 5-m-long passageway. Disregarding the entrance and roughness effects and the 90° bend, determine the pressure drop in the collector.
The impeller of a centrifugal blower has a radius of 15 cm and a blade width of 6.1 cm at the inlet, and a radius of 30 cm and a blade width of 3.4 cm at the outlet. The blower delivers atmospheric air at 20°C and 95 kPa. Disre- garding any losses and assuming the tangential components of air velocity at the inlet and the outlet to be equal to the impeller velocity at respective locations, determine the volu- metric flow rate of air when the rotational speed of the shaft is 800 rpm and the power consumption of the blower is 120 W. Also determine the normal components of velocity at the inlet and outlet of the impeller.
A 90" elbow is used to direct water flow at a rate of 0,025 m3/s in a horizontal pipe upward. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference betwoen the centers of the exit and the inlet of the elbow is 35 cm. The weight of the elbow and the water in it is considered to be negligible. Determine the anchoring force needed to hold the elbow in place A) 27 N 3433.5 N C) 79.5 N D) 132. 9 E) 106. 5 N
The friction factor in the plastic pipes for the piping system, which is shown in the figure, The diameter of the orifice located lower section of upper reservoir is 56,2 mm. The length and diameter of the pipe are 800cm and 30mm respectively. The kinematic viscosity and density of water 0.00000162 m2/s and 1000 kg/m3 respectively. Neglecting all the minor head losses and assuming that the system is operating at steady state. Determine and Solve the problem by making the necessary assumptions and drawing the schematic figure. i-volumetric flow rate through the pipe, ii-The head delivered by the pump iii- the power required by the pump, if the pump efficiency is 76,2% percent. (a=6 and b=2on the figure)
A pipe discharges 142 lps of water into a reservoir at a point 1.85 mbelow the water surface. At point A the diameter is 25.4 cm and the center of thepipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm.If the head loss from A to the reservoir is 0.7 m, determine the pressure in A.
An inverted 3-m-high conical container is initially filled with 2-m-high water. At time t = 0, a faucet is opened to supply water into the container at a rate of 3 L/s. At the same time, a 4-cm-diameter hole with a discharge coefficient of 0.90 at the bottom of the container is opened. Determine how long it will take for the water level in the tank to drop to 1-m.
The water is supplied at a pressure of 15 N/cm? to an accumulator, having a ram of diameter 2.0 m. If the total lift of the ram is 10 m, determine: (a) the capacity of the accumulator, and (b) total weight placed on the ram (including the weight of the ram). [Ans. (a) 4712.4 kNm, (b) 471240 N]
In regions far from the entrance, fluid flow through a circular pipe is one dimensional, and the velocity profile for laminar flow is given by u(r) = umax(1 − r2/R2), where R is the radius of the pipe, r is the radial distance from the center of the pipe, and umax is the maximum flow velocity, which occurs at the center. Obtain (a) a relation for the drag force applied by the fluid on a section of the pipe of length L and (b) the value of the drag force for water flow at 20°C with R = 0.08 m, L = 30 m, umax = 3 m/s, and ? =0.0010kg/m⋅s.
plzzzz help me with this one plzzz Water (viscosity of 0.001 kg/m.s and density of 1000 kg/m3 ) is to be pumped through 50 m of pipe from lower reservoir to a higher reservoir at a rate of 0.2 m3/s. If the pipe is cast iron of diameter 12 cm and the pump efficient is =0.44%, the major head loss inside the pipe is ¼ of the velocity head what horsepower pump is needed? Hint: consider the abrupt expansion only as a minor loss.