A planetary gear train is illustrated in Figure. The carrier (link 2) serves as the input to the train. The sun (gear 1) is the fixed gear and has 30 teeth. The planet gear (gear 3) has 35 teeth. The ring gear serves as the output from the train and has 100 teeth. Determine the rotational velocity of all members of this gear train when the input shaft rotates at 1200 rpm clockwise.

A planetary gear train is illustrated in Figure. The carrier (link 2) serves as the input to the train. The sun (gear 1) is the fixed gear and has 30 teeth. The planet gear (gear 3) has 35 teeth. The ring gear serves as the output from the train and has 100 teeth. Determine the rotational velocity of all members of this gear train when the input shaft rotates at 1200 rpm clockwise.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

8.7 A pair of involute gears with 16° pressure angle and 6 mm module is in mesh. The number of teeth on pinion is 16 and its rotational speed is 240 r.p.m. When the gear ratio is just 1.75, find, in order that the interference is just avoided, (a) the addenda on pinion and gear wheel (b) the length of path of contact, and (d) the maximum velocity of sliding of teeth on either side of the pitch point. (DAV Indore, 1989) (Ans. a, 9.6 mm; a 4.2 mm; 35.41 mm; V = 95.58 cm/s) %3D
A compound epicyclic gear is shown in Fig. for Q.2. C and D form acompound wheel which rotates freely on shaft G. The planet wheels B andE rotate on pins fixed in arms attached to shaft G. C and F have internalteeth: the others have external teeth with the following numbers: A, 40;B, 30; D, 50; E, 20. If A rotates at 500 rev/min and wheel F is fixed,find the speed of shaft G.
A gear system shown in Figure 1 consists of gear B and C with radii of 80 mmand 200 mm, respectively. Gear B with a mass of 0.9 kg is free to rotate at pointA of the arm AO. The arm is free to rotate on the fixed axis O. Whereas, gear Cis fixed on the axles O in a way that it will never rotate. The arm has a mass of0.8 kg and a radius of gyration about O of 140 mm. Moreover, the arm AO hasa center of gravity located at point G.Use the table method to calculate the angular speed of gear B, provided that thearm rotates at 5,118 rad/s.
A gear system shown in Figure 1 consists of gear B and C with radii of 80 mmand 200 mm, respectively. Gear B with a mass of 0.9 kg is free to rotate at pointA of the arm AO. The arm is free to rotate on the fixed axis O. Whereas, gear Cis fixed on the axles O in a way that it will never rotate. The arm has a mass of0.8 kg and a radius of gyration about O of 140 mm. Moreover, the arm AO hasa center of gravity located at point G.1.1. If the uniform torque of 4 Nm is applied to the arm OA, initially at rest in thehorizontal position, calculate the velocity of point A as it reaches the top point A’.1.2. Use the table method to calculate the angular speed of gear B, provided that thearm rotates at 5,118 rad/s.
A rack and pinion is a pair of gears that converts rotational motion into translation. As shown in the figure, a torque τ is applied to the shaft. The pinion rotates and causes the rack to translate. The mass moment of inertia of the pinion is I and the mass of the rack is m. Draw the free-body diagram and derive the differential equation of motion
Two mating involute spur gears of 20 pressure angle have a gear ratio of 2. The number of teeth on the pinion is 20 and its speed is 250 r.p.m. The module pitch of teeth is 10 mm. If the addendum on each wheel is such that the path of approach and the path of recess on each side are half the maximum possible length cach, find: i) the addendum for pinion and gear wheel, i) the length of arc of contact, iiithe maximum velocity of sliding during approach and recess. Assume pinion to be driver.
A pair of helical gears transmit 15 KW power and the pinion is rotating at 1000 rpm. The helix angle is 0.50 radians and the normal pressure angle is 0.35 radians. The pitch diameter of the pinion is 70 mm and the pitch diameter of the gear is 210 mm. Determine the tangential, radial, and axial forces between the gear teeth.
. During the operation of a punch press, its flywheel decelerates uniformlyfrom 400 rpm to 200 rpm in l sec. The rim of the flywheel weighs 1288 lb, itsinside and outside diameters are 56 in. and 60 in., and it is attached to itshub by 6 spokes. What average shearing force is developed between the rim andeach spoke during the 1 sec interval?
Shaft "a" in the figure rotates at 450 rev/min in the direction shown. Find the speed and direction of rotation of shaft "d".
Two mating involute spur gear of 20° pressure angle have a gear ratio of 2. The number of teeth on the pinion is 20 and its speed is 250 r.p.m. The module pitch of the teeth is 12 mm. If the addendum on each wheel is such that the path of approach and the path of recess on each side are half the maximum possible length, find : a. The addendum for pinion and gear wheel; b. The length of the arc of contact; c. The maximum velocity of sliding during approach and recess. Assume pinion to be the driver.
simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity of slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14.5o. The wheelchair has a maximum velocity of 5 m/s when its pinion rotates at 800 r.p.m. Calculate: 1. The magnitude of the velocity of slip of gears in mesh.2. The angular speed of the gear wheel in rad/s.3. The maximum length of a path of the approach in mm.
A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity of slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14.5o. The wheelchair has a maximum velocity of 5 m/s when its pinion rotates at 800 r.p.m. Calculate: a) The magnitude of the velocity of slip of gears in mesh. b)The maximum length of a path of the approach in mm c ) The length of a path of a recess in mm d) The addendum of the gears in mm e) The contact ratio.