A planetary gear train is shown in the figure. The sun gear (gear 1) is fixed, it has a 1-in. pitch diameter with a diametral pitch of 12. Gear 3 has 36 teeth and gear 4 has 20 teeth. Gear 5 has 40 teeth and is keyed to the same shaft as gear 4. Gear 5 mates with the ring gear (gear 6), which serves as the output from the train and has 160 teeth. The carrier (link 2) serves as the input to the train, determine the rotational velocity of the ring gear when the input shaft rotates at 1125 rpm clockwise.

A planetary gear train is shown in the figure. The sun gear (gear 1) is fixed, it has a 1-in. pitch diameter with a diametral pitch of 12. Gear 3 has 36 teeth and gear 4 has 20 teeth. Gear 5 has 40 teeth and is keyed to the same shaft as gear 4. Gear 5 mates with the ring gear (gear 6), which serves as the output from the train and has 160 teeth. The carrier (link 2) serves as the input to the train, determine the rotational velocity of the ring gear when the input shaft rotates at 1125 rpm clockwise.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Provide very clear and complete solution and diagam. SITUATIONAL PROBLEM: Two shafts are connected by spur gears. The pitch radii of the gears A and B are 200 mm and 860 mm respectively. If shaft A makes 350rpm and is subjected to twisting moment of 250 N-m. Pressure angle is 14.5 degree. What is: a.) Rpm of gear B b.) Torque in shaft B (in Newton meter). c.) Separation load of two gears (in newtons). d.) Total load on gears (in newtons).
For a pair of standard gears, the module is m=2.5mm，pressure angle is α=20 0. ha*=1. c*=0.25. The teeth number on gear 1 is z1=22. The standard center distance is a=68.75mm. Calculate the contact ratio ε with the standard center distance a, 68.75mm. ε=( )
Two equal spur gears of 48 teeth mesh together with pitch radii of 4.0 in. and addenda of 0.1670in. If the pressure angle is 14 1⁄2 deg, calculate the length of action and contact ratio.
A 84-tooth gear is driven by a 17-tooth spur pinion. The diametral pitch is 32 teeth/in and the pressure angle is 20, the length of action is equal to
A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14,5. The wheelchair has a maximum velocity of 5 m/s when it's pinion rotates at 800 rpm. Calculate : 1.1)The magnitude of the velocity of slip of gears in mesh 1.2)The angular speed of the gear wheel in rad/s 1.3)The maximum length of a path of the approach in mm 1.4)The length of a path of a recess in mm. 1.5) The addendum of the gears in mm. 1.6) The contact ratio
Find the diameter of each gear using one simple gear train with 4 gears that work as a speed reducer with a ratio of 5:1 Input of 100 rpm, Output of 20 rpm. Consider number of teeth as: N1=20 N2=40 N3=80 N4=100 Use module of 2
A pinion having 40 teeth is meshing with a spur gear having 80 teeth. The profile of the gear is involute. The module of the gears is 12 mm and pressure angle is 20 degree. The addendum of the gears is 10 mm. Find the length of path of contact, arc of contact and the contact ratio.
7. The following data relate to a pair of 20° involute gears in mesh : Module = 6 mm, Number of teeth on pinion = 17, Number of teeth on gear = 49; Addenda on pinion and gear wheel = 1 module. Find : (a) The number of pairs of teeth in contact (b) The angle turned through by the pinion and the gear wheel when one pair of teeth is in contact (c) The ratio of sliding to rolling motion when the tip of a tooth on the larger wheel (i) is just making contact (ii) is just leaving contact with its mating tooth (iii) is at the pitch point.
Two straight-toothed bevel gears mesh with a shaft angle of 90° and a diametral pitch of 5. The pinion has 20 teeth, and the gear ratio is 2:1. The addendum and dedendum are the same as for 20 stub teeth. For the gear, determine the pitch radius, cone angle, outside diameter, cone distance, and face width.
A pair of spur gear fitted on a motor shaft of lathe machine transmits the power of 7 kW at 600 rpm which is input at pinion gear and its shaft rotates in the counter-clockwise direction. The number of teeth on the pinion and the gear are 22 and 72 respectively, while the module is 8 mm. Assume a pressure angle of 200. Calculate: i) Torque on the shaft of the pinion in Nm. ii) Torque on the shaft of the gear in Nm. iii) Gear ratio iv) Center distance between shafts in mm
A pair of straight-tooth bevel gears (as shown in the figure above) are in mesh transmitting 35 hp at 1000 rpm (pinion speed). The gear rotates at 400 rpm. The gear system has a pitch of 6 and a 20-degree pressure angle. The face width is 2 inches and the pinion has 36 teeth. Determine the tangential, radial, and axial forces acting on the pinion
An epicyclic gear shown in Figure 1 consists of ring gear, planet gear and sun gear. The ring gear has 72 internal teeth and sun gear has 32 external teeth. Planet gear meshes with both ring and sun gears and is carried on an arm which rotates about the centre of the ring gear at 20 r.p.m. If the gear A is fixed, Calculate the speed of plane gear.