A proportional controller has a PB of 50%. A level-tank is calibrated as follows: 20 mm = 0 % and 120 mm = 100 % If Process Variable = PV = 65%, Set Point = SP = 80 mm and MR = 20%. Calculate the error(s) and output(s) of Controller? %3D Errors are 5% and -5% and outputs are 10% and 30% respectively Errors are -5% and 5% and outputs are 10% and 30% respectively Ob. Errors are 5% and 5% and outputs are 10% and 30% respectively Oc Errors are -5% and -5% and outputs are 10% and 30% respectively

A proportional controller has a PB of 50%. A level-tank is calibrated as follows: 20 mm = 0 % and 120 mm = 100 % If Process Variable = PV = 65%, Set Point = SP = 80 mm and MR = 20%. Calculate the error(s) and output(s) of Controller? %3D Errors are 5% and -5% and outputs are 10% and 30% respectively Errors are -5% and 5% and outputs are 10% and 30% respectively Ob. Errors are 5% and 5% and outputs are 10% and 30% respectively Oc Errors are -5% and -5% and outputs are 10% and 30% respectively

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter13: Magnetic Induction

Section: Chapter Questions

Problem 1PA

See similar textbooks

Similar questions

What are the types of controllers? Draw the block diagram for PID controller and state the áre applications.
What will be the controller output for a Proportional Integral Derivative controller i) Initially and ii) after T= 1 seconds after the error begins to change from zero at the rate of 2%/s.The controller has Kp=3.5,KD=0.4 seconds and KI=0.01 /seconds.
A binary code to represent the decimal digits [0-9] must contain at least four bits because 3digits can only represent until the decimal number _____ a) 8 b) A c) 7 d) 9 The effect in which the measurement is attempted to be modified is called_____ a) Preventive maintanance b) corrective maintenance c) calinration d) loading The controller that produces a control action preportional to the error is called_____________ a) derivative b) integral c) proportional d) on-off controller
How to reduce the loading effect in an ammeter? Explain the controller output of different types of PI and PID controllers with necessary equations
Suppose that the contents of certain memory locations are as shown in Figure P8.34. Furthermore, for each part of this problem, the initial contents of the CPU registers are: ( D)=$0003,( X )=$1 FFF, and (Y)=$1000. Name the type of addressing and determine the contents of registers D, X, and Y after each of these instructions is executed: a. ADDB $1002,Y b. LDAA B,X c. LDAB 7, +X d. LDX [$1004,Y] e. LDAA [D,X]
A PID controller has a test input signal: parabola=t^2/2. Kp=5, Ki=1, Kd=80. Determine the controller output at t=3 seconds. ans:1
How to reduce the loading effect in a voltmeter? Explain the controller output of different types of PD and PID controllers with necessary equations.
A PID controller has a test input signal: Unit Ramp. Kp=3, Ki=0.60, Kd=8. Determine the controller output at t=4 seconds. A Unit Ramp function has a value of zero prior to t=0, and a slope of 1 after t=0. ans:1
5.- Design a microcontroller system to control a sprinkler controller that performs the following tasks. We assume that your microcontroller is clocked at 10 MHz and has a 16-bit free-running counter. The sprinkler controller system controls two different zones by turning the sprinklers within each zone on and off. To turn on the sprinklers in a zone, the controller needs to receive a 152.589 Hz PWM signal from its microcontroller. To turn off the sprinklers in the same zone, the controller needs to receive the PWM signal with a different duty cycle. B.- After 15 min, your microcontroller must send the PWM signal with a 15% duty cycle of 10 ms to turn off the sprinklers in zone one.
5.- Design a microcontroller system to control a sprinkler controller that performs the following tasks. We assume that your microcontroller is clocked at 10 MHz and has a 16-bit free-running counter. The sprinkler controller system controls two different zones by turning the sprinklers within each zone on and off. To turn on the sprinklers in a zone, the controller needs to receive a 152.589 Hz PWM signal from its microcontroller. To turn off the sprinklers in the same zone, the controller needs to receive the PWM signal with a different duty cycle. D.-After 15 min, your microcontroller must send the PWM signal with a 25% duty cycle of 10 ms to turn off the sprinklers in zone two.
77. PD Control What will the controller output be for a proportional plus derivative controller(a) initially and(b) 3 sec. after the error begins to change from the zero errorat the rate of 4%/s. The controller has KP=5 and Td=0.6 s
What do you mean by I controller? Draw the electronic circuit of I controller and also write the electronic output equation and General controller output equation.?