An automated QA machine selests the product in an industry based on the perfsstion of color, weight, and length which are expressed by the variables C, W, and L, respectively. If a feature is perfect the machine takes input as 1', 0' otherwise. Based on the conditions, machine decides whether to reject (R) a product or not. Assume R = 1 if two (or more) of the features are not perfect. Otherwise, R = 0. (5-a) Apply your knowledge of Boolean logic to form the truth table (5-b) Use K-map to find the formula for the above scenario. (5-c) Draw the circuit diagram for the given scenario using minimum number of practical gates. (5-d) Draw the circuit diagram for the given scenario using NAND gates only.

An automated QA machine selests the product in an industry based on the perfsstion of color, weight, and length which are expressed by the variables C, W, and L, respectively. If a feature is perfect the machine takes input as 1', 0' otherwise. Based on the conditions, machine decides whether to reject (R) a product or not. Assume R = 1 if two (or more) of the features are not perfect. Otherwise, R = 0. (5-a) Apply your knowledge of Boolean logic to form the truth table (5-b) Use K-map to find the formula for the above scenario. (5-c) Draw the circuit diagram for the given scenario using minimum number of practical gates. (5-d) Draw the circuit diagram for the given scenario using NAND gates only.

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter29: Service-entrance Calculations

Section: Chapter Questions

Problem 3R: a. What is the ampere rating of the circuits that are provided for the small-appliance loads? _____...

See similar textbooks

Similar questions

Draw the Nyquist plot for the system in the figure below. Using the Nyquist stability criterion, determine the range of K for which the system is stable. Consider both positive and negative values of K.( Need only handwritten solution please otherwise downvote)
Signals and Systems question. I am trying to find the characteristic polynomial, equation, roots, modes, along with the zero-input component of the response for (D2+9)y(t), with the given initail conditions. So far, I was able the roots of it to be 0α +/-3β, which would make the the characteristic mode ce0TCos(3T+θ) due to it having complex roots, but since anyhting to the zero is just one, it would make it cCos(3T+θ). Is this correct? If not, where did I mess up?
Show your complete solution for the theoretical computations. Thanks!
1 What is the standard Deviation ? Describe a scenario in which you would use each by given an example in electrical measurement and instrumentation? 2.What is the population standard deviaion ?Describe a scenario in which you would use each by given an example in electrical measurement and instrumentation ? 3. How do the statistics calculated using engineering and IT tools compare? And the statistics that are calculated by hand? 4.What is the importance of modern engineering and information technology in measurement and testingElectrical devices؟
Given the unit step responses below. If percent overshoot is the ratio of the difference of the peak value and settling value to its settling value; solve for the estimated percent overshoot for each of the following P, PD, PI, PID controllers
Question 1) In a dynamic system with expression [img1] in the time domain, all initial conditions are assumed to be zero. This system will be used in the standard unit feedback control system, and the reference input is unit stepfunction, the controller is a PD controller given with [img2]. Accordingly, fill in the table below. The numerical solver (Configuration Parameters under Simulation in the menu) parameters for this stage are shown above. Table 1: Design Results Exceed (%) ?? Rise time (s) ?? Sitting time (s) ?? Peak time (s) ??
subject (control engineering) pls show full steps sir take your time sir
Each item below describes key characteristics of a particular system (that is, a plant transfer function). For each system, describe the effect of proportional control on the stability of the closed-loop system. Specifically, 1) what can you say for small gains, and 2) what for large gains? (E.g., stable, unstable, inconclusive.) Provide a short explanation of your answers, with sketches as necessary.
Assume ?? ≈ 0. Solve this problem using both the exponentialmodel and the constant-voltage model. For the constant-voltage model, use ???,?? = 0.7?
Q5. Explain how the Artificial Intelligence (AN) can be applied to power system protection? Discuss the advantage of Al based numerical protection. Describe the Artificial Neural Network properties and capabilities for application to power system protection.
Given a choice between P or PI controller ?cl(?), choose the controller (and its’ parameters)that will result in a Type 1 system (with respect to steady-state error) and a steady-state error toa unit-ramp r(t)=t u(t) which is less than 1/10.
A university wants to establish a control system model that represents the student population as an output, with the desired student population as an input. The administration determines the rate of admissions by comparing the current and desired student populations. The admissions office then uses this rate to admit students. Draw a functional block diagram showing the administration and the admissions office as blocks of the system. Also show the following signals: the desired student population, the actual student population, the desired student rate as determined by the administration, the actual student rate as generated by the admissions office, the dropout rate, and the net rate of influx