A rectangular barge 200,000 kg, 14 m long, 8 m wide and 4.5 m deep will be used to transport round steel bars 20 mm in diameter by 6 meters long. If the density of steel bars is 7,850 kg/m³ and for sea water is 1,030 kg/m³. How many pieces of round steel bars can be transported from Manila to Polloc port?

A rectangular barge 200,000 kg, 14 m long, 8 m wide and 4.5 m deep will be used to transport round steel bars 20 mm in diameter by 6 meters long. If the density of steel bars is 7,850 kg/m³ and for sea water is 1,030 kg/m³. How many pieces of round steel bars can be transported from Manila to Polloc port?

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Polycarbonate, PC, is used for aircraft canopies. A batch of this polymer was found to fail prematurely when impacted by a 4 pound bird during qualification studies. You suspect that the problem is due to a molecular weight difference for this particular batch of polymer compared to previous batches. You decide to perform dilute solution viscosity studies to determine the Mol.wt. Assume density is 1.2g/cm3 What solvent would you use? Justify your answer Please answer very soon will give rating surely
A waste treatment pond is 50 m long and 25 m wide, and has an average depth of 2 m. The density of the waste is 75.3 lbm/ft3 . Calculate the weight of the pond contents in lbf, using a single dimensional equation for your calculation.
Table 1 below shows the data for the filtration of fruit juice to produce clarified fruit juice at 298.2 K. Table 1: Total volume of filtrate collected at certain time V * 103 (m3) t (s) 0.5 17.3 1.0 41.3 1.5 72.0 2.0 108.3 2.5 152.0 3.0 201.7 The filtration process was conducted at a constant pressure of 46.2 kN/m2. The area of the plate-and-frame the press was 0.0439 m2, and the pulp concentration was 23.47 kg solid/m3 filtrate. a) Convert the data in Table 1 into a graph. You can either use Excel or graph paper. Your graph should be self-explanatory. b) Using the graph in (a), estimate the specific cake resistance and the resistance of the filter medium to filtrate flow.
A 5.00 wt% sulfuric acid solution in water has a density of 1.03 g/mL and is flowing through a 45-meter long pipe that has a 6.0 cm diameter at a rate of 82 liters per minute. The average velocity of a fluid in a pipe equals the volumetric flow rate divided by the cross-sectional area normal to the direction of flow. How long in seconds does it take the solution to flow through the 45-meter long pipe?
1. Estimate the density of a 25-API gravity dead oil at 100 F.
A vessel of 4m3 volume contains an oil which weighs 30.2KN. Determine the specific gravity of the oil.
H2. Cartons of product are accumulated on the floor adjacent to a conveyor. The job consists of a worker lifting the cartons from the floor and placing them on the conveyor. The height of the conveyor is 61 cm. The cartons are 30 cm height, 30 cm width, and 40 cm length . The horizontal distance from the worker’s ankles to the center of the carton is 20 cm. Carton weight is 9 kg. Frequency of lift is 2 lifts per minute and the duration of the task is between 1 and 2 hours. The cartons have a fair handholds. Control at the destination of lift is not required. The angle of asymmetry at the origin of lift may be taken to be 45 degrees. Use the NIOSH equation to calculate the Recommended Weight Limit (RWL) and the Lifting Index (LI). Comment on the safety of this lifting task.
A spent sulfuric acid solution is brought up to strength for a pickling process in a mixer. Spent solution at 3% sulfuric acid (by weight) is mixed with a 50% solution (by weight) to obtain the desired product concentration of 40% acid by weight. All are aqueous solutions. Determine all flow rates on the basis of 100 lbm per hour of product. If the actual flow of the spent stream is 300 lbm per hour. What must the flow rates of the stream be?
For a wall of constant thickness, the rate of heat transfer is defined as: Determine the rate of heat transfer, Q, from your garden to the living room of your home if the outside temperature is measured as 555oR and the inside temperature is 23.2°C. The wall of your living room has a surface area of ±20 m2. The thermal conductivity of bricks, k, is 0.6934 BTU/(hr.ft2.°F).
Assume you have 0.5 m3 of soil with a porosity of 40% and an oven-dry weight of 700 kg. Calculate the bulk density. Next, assume that I drive over the soil with heavy equipment, compact the soil, and reduce the porosity from 40% to 20%. Calculate the bulk density after compaction.
In an industrial chemical process, salt solution enters a mixing tank at a rate of 5 kg/s. Industrial water enters the same tank at the rate of 20 kg/s. They are thoroughly mixed together and the diluted solution leaves the tank. If the liquid in the tank is to remain constant, determine the rate of flow of the diluted solution. (Answer in kg/s)
Cereal is being dried in a vertical drier by air flowing countercurrent to the cereal. To prevent breakage of the cereal flakes, some of the exit air from the drier is recycled back to mix with the the moist fresh air. For each 1000 kg/hr of wet cereal fed to the drier, calculate the input of moist fresh air in kg/hr and recycle rate in kg/hr. The available data on stream compositions is (fractions): For water: Fresh air: 0.0132 Wet cereal: 0.200 Exit air: 0.263 Dried Cereal: 0.050 Air entering Dryer: 0.066