ProblemsCircular rodTwo rods supportthe shelf20Shelf1200 mmFIGURE P3-9 Shelf support rods for Problem 3-9, A to bold crates haviogShelf is being designeda total mäss of 1840 kg. Two support rods likethat shown in Figure P3-9 will hold the shelfthat the center ofgravityof the eratesisar the middle of the shelf. Specify the requireddiameter oflthe circulartods to limit the stress to110 MPal

Answered: Image /qna-images/answer/38a10e12-9ae1-46e4-9f8e-5b5fe4b77d17.jpg

A shelf is being designed to hold crates having a total mass of 1840 kg. Two support rods like that shown n Figure P3-9 will hold the shelf. Assume that the center of gravity of the crates is at the middle of the shelf. Specify the required, diameter ofthe circular rods to limit the stress to 110 MPa.

A shelf is being designed to hold crates having a total mass of 1840 kg. Two support rods like that shown n Figure P3-9 will hold the shelf. Assume that the center of gravity of the crates is at the middle of the shelf. Specify the required, diameter ofthe circular rods to limit the stress to 110 MPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.25P: A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just...

See similar textbooks

Similar questions

The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind the maximum shear stress on the clement and show the state of stress on a sketch of a properly oriented clement.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
-7 Repeat Problem 2.3-5, but n include the weight of the bar. See Table I-I in Appendix I for the weight density of steel.
Two separate cables AC and BC support a sign structure of weight W = 1575 lb attached to a building. The sign is also supported by a pin support at O and a lateral restraint in the '-direction at D. (a) Find the tension in each cable. Neglect the mass of the cables. (b) Find the average stress in each cable if the area of each cable is Ae= 0.471 in2.
A steel punch consists of two shafts: uppershaft and lower shaft. Assume that the upper shafthas a diameter d1 = 24 mm and the bottom shaft hasa diameter d2 =16 mm. The punch is used to inserta hole in a 4 mm plate, as shown in the figure. If aforce P = 70 kN is required to create the hole, whatis the average shear stress in the plate and the averagecompressive stress in the upper and lower shaft ofthe punch?
Three rods jointly support a 8kN load. Assumingthat there was no stress in the rods before theload was applied, find the stress in each rod.θ = 25oα = 20oProperties:Modulus ofElasticityCrosssectionalAreaSteel 200 GPa 250mm2Bronze 83 GPa 250mm2
Rod of diameter 20 mm is loaded with 5kN tension force. What is the magnitude of stress in the rod?
The bolt shown on the picture is subjected to total tensile force of 90 kN. Determine the tensile stress at the body of the bolt and tensile stress at root of bolt. Find also the compressive stress at the head as the bolt bears on the surface to resist the tensile load.
The figure shows 16-mm diameter bolts used to hold two steel plates by fitting inside a cylindrical spacers. Thenormal stress must not to exceed 230 MPa in the bolts and 160 MPa in the spacer. Determine the outer diameterof the spacer.
The cylinder is shown in Figure is made of steel having a specific weightof gst = 490 lb>ft3. Determine the average compressive stress acting atpoints A and B.
Compute the maximum stress in the member, considering stress concentrations. Use Figure P3-66 2.00-in dia. 0.10-in radius 1.25-in dia. Applied torque = 2200 lb-in