Choice the correct answer A short shunt compound wound d.c generator supplies aload current of 390A s at 250V. the generator has followingresistances: Armature resistance=D0.152, Series resistance =0.1 Q. The current of shunt field winding equal 10A,Calculate the e.m.f generator, if the brush drop is 1 volt /brush *O 351 V348.5V352VO 349.5 V

Given short shunt compound D.C generatorLoad current IL=390 ATerminal voltage V=250 vArmature…

A short shunt compound wound d.c generator supplies a load current of 390A s at 250V. the generator has following resistances: Armature resistance=0.152, Series resistance = 0.1Q. The current of shunt field winding equal 10A , Calculate the e.m.f generator, if the brush drop is 1 volt / brush * 351 V 348.5V 352V 349.5 V

A short shunt compound wound d.c generator supplies a load current of 390A s at 250V. the generator has following resistances: Armature resistance=0.152, Series resistance = 0.1Q. The current of shunt field winding equal 10A , Calculate the e.m.f generator, if the brush drop is 1 volt / brush * 351 V 348.5V 352V 349.5 V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A compound generator has an efficiency of 87% at 200V, 10kW rated output. If the series field resistance of 0.03 ohm, armature resistance of 0.05 ohm and shunt field resistance is 50 ohms. Find the efliciency at half load.
A 220V series generator has an armature resistance of 0.4ohms. If the generated emf is 230V and the drop across the series field winding is 8V, what is the value of armature current (in amp)?
A 500-V, wave-wound, 750 r.p.m. shunt generator supplies a load of 195 A. The armature has 720 conductors and shunt field resistance is 100 Ω. Find the demagnetising amp-turns/pole if brushes are advanced through 3 commutator segments at this load. Also, calculate the extra shunt field turns required to neutralize this demagnetisation.
Two similar 6,600-V, three phase generators are running in parallel on constant-voltage andfrequency bus bars. Each has an equivalent resistance and reactance of 0.05 Ω and0.5 Ω respectively and supplies one half of a total load of 10,000 kW at a laggingp.f. of 0.8, the two machines being similarly excited. If the excitation of onemachine be adjusted until the armature current is 438 A and the steam supply to theturbine remains unchanged, find the armature current, the e.m.f. and the p.f. of theother alternator.
A 150-kW 250-volt compound generator is connected long shunt. If the shunt field resistance is 20 ohms, what is the series field-current at full load? (Ans.: 612.5 A) write diagram, given, etc
A short shunt compound DC generator delivers a load current of 30 A at 220 V and has armature, series field and shunt field resistances of 0.05, 0.3 and 200Ω respectively. Calculate the induced emf, the armature current and the voltage regulation. Allow 1 V per brush for contact dro
An 8-Pole, simplex lap wound, shunt generator has 800conductors and a flux per pole of 0.025Wb and running at 1200rpm. The armature and shunt field resistances are 0.25Ω and 120Ω respectively. If the armature voltage drop is equal to 10V, what is the load current (in Amp)? use two decimal places if the answer is not exact and do not include the unit anymore.
A long-shunt compound generator supplies 50 kW at 230 V. the total field- and armature circuit resistances are 46 ohms and 0.03 ohms , respectively. The brush-contact drop is 2 V. Determine the percent voltage regulation. Neglect the armature reaction.
A 230V shunt motor has an armature resistance of 0.28Ω and a field resistance of 115Ω. At no-load, the line current is 8A and the speed is 2300rpm. What is the speed when the line current is 52A? Assume brush drops of 1V at no-load and 3V at load condition and constant flux density. 2154rpm 2212rpm 2178rpm 2155rpm
Problem: The field current of a 100-kW, 250V shunt generator is 5A when delivering power at rated terminal voltage and rated load current. The combined armature and brush resistance is 0.1 ohm. 1.)Calculate the generated power in kW. 2.)What is the electrical efficiency? * Formatt: given required solution answer
The armature winding resistance of a long shunt connected DC generator is 0.4ohm, the resistances of the shunt and serial field windings are 125 ohms and 0.1 ohms, respectively. While the generator supplies 8KW of power to the load it feeds, which is the voltage it produces since the output voltage is 250V?
The terminal voltage of a 75-kW shunt generator is 600 V at rated load. The resistance of the shunt-field circuit is 150 Q, and the armature-circuit resistance is 0.1 Ω. Find the generated emf. a) 612.9 V b) 621.9 V c) 692.1 V d) none of the above In a 50-kW 245-V shunt generator, 258 V are generated in the armature when the generator delivers rated load at rated voltage. The shunt-field current is 4 A. Find the resistance of the armature. a) 0.03 Ω b) 0.062 Ω c) 0.106 Ω d) none of the above A load that has a resistance of 8 Ω is connected to a separately excited generator that has an armature-circuit resistance of 0.5 Ω. A) What is the armature current when the generated emf is 130 V? a) 1.53 A b) 15.3 A c) 153 A d) none of the above