A solid shaft of 200 mm diameter has the same cross-sectional area as that of hollow shaft of same material with outside diameter is 300 mm. Both the shaft has got same shear stress. Find the ratio of power transmitted of sold to hollow shah at the same speed. 0.43 0.67 1.7 2335

A solid shaft of 200 mm diameter has the same cross-sectional area as that of hollow shaft of same material with outside diameter is 300 mm. Both the shaft has got same shear stress. Find the ratio of power transmitted of sold to hollow shah at the same speed. 0.43 0.67 1.7 2335

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A hollow steel shaft transmits 600 kW at 500 r.p.m. The maximum shear stress is 62.4 MPa. Find the…

A: Find the outside and inside diameter .

Q: A simply supported shaft between bearings camies a steady load of 10 kN at the centre. The length of…

Q: A flange coupling joining two sections of shaft is required to transmit 250 kW at 1000 r.p.m. If six…

Q: (b) A hollow shaft, having an inside diameter of 60% of its outer diameter, is to replace a solid…

A: It is given that the material, power transmitted and the speed of the both shafts is same. Torque…

Q: A torsion dynamometer is fitted on turbine shaft to measure the angle of twist. It is observed that…

Q: A hollow shaft is to transmit 300 kW at 80 r.p.m. If the shear stress is not to exceed 60 MN/mm²…

A: Given that , P=300kW N=80 rpm Maximum shear stress = 60MN/mm2 internal diameter = 0.6 × external…

Q: A 9-in solid shaft has the same cross-sectional area as the hollow shaft of the same material with…

A: Given Data The diameter of the solid shaft is: D=9 in The inner diameter of the hollow shaft is:…

Q: A hollow shaft transmits 9 MW at 300 rev/min. It is supposed that the maximum allowable stress is…

A: Given: The power transmitted by the shaft is P=9 MW. The maximum allowable shear stress is ζ=70…

Q: A solid steel shaft 3 m lang is stressed to 65 MPa when twisted through 2º. A. Given that G = 83…

A: Modulus of rigidity: It is the ratio of shear stress to shear strain. Shear stress: The ratio of…

Q: A solid steel shaft is stressed at 100 Mpa when twisted through 6 degrees. Compute the Diameter of…

A: Given:ζ=100 MPaθ=6°f=25 HzL=15 mG=83 GPa

Q: A solid shaft in a rolling mill transmits 30kW at 100 rpm. Find the diameter in mm of the shaft so…

A: Answer: The diameter of the shaft is 63.35 mm. Hence, the correct answer is option (c).

Q: 5.1 A steel shaft is to transmit 4.5 MW at 3 Hz without exceeding a shearing stress o: MPa, or…

Q: 1.2. A solid and a hollow shaft are made of same material. The diameter of the solid shaft is 300 mm…

A: Given, Diameter of the solid shaft , ds = 300 mm Inside diameter of the hollow shaft, dhi = 250 mm…

Q: Find the diameter of a solid steel shaft to transmit 43kW at 5.25 rps. The ultimate shear stress for…

A: The shaft is a device which is used to transmit power from one place to another. The torque…

Q: A 50 mm diameter shaft is transmitting a power of 142.8 HP and is turning at 900 rpm. The shaft is…

A: given data ; diameter = 50 mmpower = 142.8 HP = 142.8 * 746 Wrpm = 900 rpmbending stress =…

Q: What is the maximum power P (kW) that can be transmitted by a shaft hollow (do = 50 mm, di = 40 mm)…

A: Outer diameter of shaft= 50mm Inner diameter of shaft= 40mm Rotational Speed of shaft= 600 rpm…

Q: (Q1 A hollow shaft has to transmit 6 MW at 150 rev/min. The maximum allowabl て 180 L=1 stress is not…

Q: A solid and a hollow shaft are made of same material. The diameter of the solid shaft is 300 mm and…

Q: A turbine's propeller shaft transmits 7.5 kW at the speed of 240 rev/min. The shaft has an internal…

Q: (a) A steel transmission shaft is 510 mm long and 50 mm external diameter. For part of its length it…

A: We can consider this case as shafts in series Both parts are subjected to the same torque We know…

Q: Find the diameter of a shaft to transmit twisting moments varying from 800 N-m to 1600 N-m. The…

Q: Design a hollow shaft required to transmit 11.2 MW at a speed of 300 r.p.m. The maximum shear stress…

Q: A shaft is used to transmit 24 kw at a speed of 1,779 rev/min. Using a maximum allowable shear…

Q: A circular shaft of 60 mm diameter is running at 150 r.p.m. What will be the torque transmitted by…

A: Given, Diameter of shaft = d = 60 mm Shear stress in the shaft = τ = 80 MPa From the relation…

Q: Determine the diameter of a solid steel shaft that will transfer 30 MW at 1500 RPM with a 1 degree…

A: Given Data P=30 MW N=1500 rpm Angle of twist=1° L=20D G=80 GN/m2

Q: A shaft supported on bearings 200mm apart transmits 187 kW at 200rpm. The maximum bending moment is…

Q: 3. A steel shaft transmits 30KW at 1500rpm. Considering allowable shearing stress of degrees 351.6…

Q: A hollow steel shaft transmits 600 kW at 500 r.p.m. The maximum shear stress is 62.4 MPa. Find the…

Q: A steel propeller shaft is to transmit 4.5 MW at 3 Hz without exceeding a shearing stress of 60 MPa…

Q: A solid shaft has 100 mm diameter. It is used to transmits 120 watt power at 200 rpm (Take G = 8 x…

A: Given:Power transmited P=120π Wmodulus of rigidity G=8×104 N/mm2Diameter of shaft d=100 mm or 0.1…

Q: A solid circular shaft to transmit,80kw power at 200rpm.calculate the shaft diameter and strain…

Q: Design a suitable diameter for a circular shaft required to transmit 90 kW at 180 r.p.m. The shear…

A: GIVEN DATA- MAXIMUM SHEAR STRESS = 70MPa POWER P=90KW SPEED N=180 r.p.m. MAXIMUM TORQUE = 140% OF…

Q: Example 7.5: (Numerical problem of a circular shaft) A circular shaft 10 cm diameter and 1.1 m…

Q: A solid shaft, 150 mm in diameter, is to be replaced by a hollow shaft of the same length and…

Q: A turbine’s propeller shaft transmits 7.5 kW at the speed of 240 rev/min. The shaft has an internal…

A: Any action that can change the state of motion is called force, Force is described by its magnitude,…

Q: A hollow steel propeller shaft is to transmit 4.5 MW at 3 Hz without exceeding a shearing stress of…

A: GivenP=4.5MWf=3hzζ=50Mpa

Q: A solid shaft of 250 mm diameter has the same cross-section area as the hollow shaft of the same…

A: Given data: The diameter of the solid shaft, ds = 250 mm. The outside diameter of the hollow shaft,…

Q: A ship's shaft operates at 150 rpm and resists a maximum shear stress of 50 MPa. The shaft has an…

A: To solve this problem, we have used torsion equation. Proper care of units must be taken.

Q: A stepped shaft of diameters 3D and D transmits 1 MW of power.The torque on the larger diameter…

Q: A solid shaft is transmitting 1MW at 240rpm . Determine the diameter of the shaft if the maximum…

Q: a solid shaft is transmitting 1 mw at 240 rpm determine the daimeter of shaft exceed the mean of…

A: Shear stress produced by torque vary from zero at center of cross-section to maximum at surface in…

Q: A belt drive consists of two V-belts in parallel, on grooved pulleys of the same size. The angle of…

Q: 5. A propeller solid shaft of a ship with 200 mm diameter transmit a power of 5 MW at 500 r.p.m. It…

A: The diameter of solid shaft, The power of solid shaft, The speed of solid shaft, Now, the power…

Q: Calculate the torque which a 11/11 shaft of 100 mm Radius can safely transmit, if the shear stress…

A: Given data: Radius of the shaft (R) = 100 mm Shear stress τ=50 N/mm2 Need to determine the torque…

Q: A solid rotating shaft made of Annealed AISI 1030 is used in a boat with a high speed as shown in…

Q: Q3) A ship's propeller shaft has external and internal diameters of 25 cm and 15 cm. What power can…

Q: Q) A two-segment shaft is used to transmit power at constant speed through the pulleys shown above…

A: In physics and mechanics, torque is the rotational equivalent of linear force. It is also referred…

Concept explainers

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.

Question

A solid shaft of 200 mm diameter has the same cross-sectional area as that of hollow shaft of same
material with outside diameter is 300 mm. Both the shaft has got same shear stress. Find the ratio of
power transmitted of sold to hollow shah at the same speed.
0.43
0.67
1.7
2.325

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please don't copy Find the torque and power transmitted by a 100 mm diameter shaft, if maximum angle of twist and length of shaft are 1.2° and 2 m. Take G = 70 GPa, speed of shaft = 230 r.p.m.
A shaft is used to transmit 24 kw at a speed of 1,779 rev/min. Using a maximum allowable shear stress of 48 MPa, find the shaft diameter in mm
Please solve only if you know the answer. A hollow steel shaft, 12 m long, is required to transmit 1000 kW when running at a speed of 300 r.p.m. If the maximum permissible shear stress in the shaft is 80 N/mm² and the ratio of inner 3/4 diameter to the outer diameter is , find the dimensions of the shaft.
A hollow shaft with a length of 1103mm and outer diameter 73mm and inner diameter 50mm is required to tranmit a power of 60kW at a speed of 2950 rpm if the modulus of rigidity is 79.5GPa calculate the maximum shear stress in the shaft
A 16 ft steel line shaft has no bending action except its own weight. What power in hp can shaft deliver at a speed of 200 rpm. Consider that the torsional deflection wm not exceed 0.08o/ft of length.
A solid shaft of 150 mm diameter is used to transmit torque. Find the maximum torque transmitted by the shaft if the maximum shear stress induced to the shaft is 45 N/mm2
A solid shaft, 150 mm in diameter, is to be replaced by a hollow shaft of the same length and similar steel but of only 80 % of the volume of the solid shaft. Calculate the sizes of the hollow shaft if the power to be transmitted is 20 % greater and the speed of the shaft is increased by 50 %. The maximum shear stresses induced may be taken as equal in both cases.
A hollow shaft has to transmit 6MW at 150rev / min. The maximum allowable stress is not to exceed 60 MN / m? nor the angle of twist 0.3 ° per meter length of shafting. If the outside diameter of the shaft is 300 mm find the minimum thickness of the hollow shaft to satisfy the above conditions. G = 80 GN / m?
A turbine’s propeller shaft transmits 7.5 kW at the speed of 240 rev/min. The shaft hasan internal diameter of 150 mm. Calculate the minimum permissible external diameter ifthe shearing stress in the shaft is to be limited to 150 MPa
find the maximum shear stress induced in a solid circular shaft of diameter 150 mm when the shaft transmits 150 KW power at 150 RPM.
A full circular cross-section shaft will be designed to provide power transmission at 220 (revolution/minute) revolution of a 12300 kW engine. Since the shaft length is 3 m, the material shear modulus is 80 GPa, and the shear yield stress is 190 MPaa) How many kN.m torque should the shaft carry?b) Write down the minimum safe shaft radius in metersc) How many rad is the shaft at the specified minimum radius. found?
A solid shaft of 200 mm diameter has the same cross sectional area as that of a hollow shaft of the same material with the inside diameter of 150 mm. Find the ratio of the power transmitted by the two shafts at the same speed. Show necessary figure and all calculations involved