A solid bar of circular cross section has a diameter of 40mm and length of 1300mm. G=80GPa and torque applied at both ends is 340 N.m. Determine the angle of rotation in radians.
Q: Two torque as shown are applied on a compound shaft of aluminum segment and a steel. Determine the…
A:
Q: When a circular rod of diameter 10 cm and length 10 m is subjected to torque of 10 kN-m. Then angle…
A:
Q: A single torque of T = 60 N.m is applied to a compound torsion member. Segment (1) is a 32-mm…
A:
Q: *1Q4 A hollow steel shaft of 100 mm external diameter (D) and 50 mm internal diameter (d) is…
A: When the force is applied in tangential direction in the plane of transverse cross-section, torque…
Q: A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to…
A: The given values are - do =75 mm, t=5 mm, T =4090×1000 Nmm, G =80×1000 Mpa, L=2000mm The inside…
Q: A solid stainless steel [G = 93 GPa] shaft that is 2 m long will be subjected to a pure torque of T…
A:
Q: A solid shaft in a rolling mill transmits 20 kW at 2 revolutions per second. The length of the shaft…
A:
Q: Two designs for a shaft are being considered. Both have an outside diamete of 80 m and are 100 cm…
A:
Q: Determine the torsional stiffness of a solid aluminum shaft of length 2 m and radius of 30 cm. The…
A:
Q: the twisting angle. The modulus of Rigidity for the shaft is 20 GN/m? • for the missing torque T =…
A: For the shafts in series,…
Q: 75 N.m C 125 N.m 2 m 1m A steel shaft is fixed at A and is subjected to the torques as shown.…
A: Given data: dAB=50 mmdBC=30 mmG=77 GPa Need to determine the torque in segment AB, BC and angle of…
Q: A shaft when subjected to pure torsion developed a stress of 50 Mpa. If polar moment of inertia is…
A:
Q: d3 T3 T2 T1 d1 TP. B L3 L2 L1.-
A: The polar moment inertia of a circular cross-section is defined as moment of area about the axis…
Q: The circular shaft AB consists of a 19.5 mm diameter solid steel cylinder in which a 5.3 mm diameter…
A:
Q: A hollow steel shaft with an outside diameter of 80 mm and a wall thickness of 11 mm is subjected to…
A:
Q: A 1100 Nm torque is applied at B (CW looking from C towards A). Shaft (1) is solid brass with G 40…
A:
Q: A solid steel post is subjected to pure torsion. Given: -post Diameter = 65 mm -length = 2.75 m…
A:
Q: A hollow circular cold-rolled bronze [G1 - 6200 ksi] tube (1) with an outside diameter of 1.75 in.…
A:
Q: A hollow steel shaft with an outside diameter of 64 mm and a wall thickness of 5 mm is subjected to…
A:
Q: A hollow steel shaft with an outside diameter of 62 mm and a wall thickness of 6 mm is subjected to…
A: Given that , Outside diameterDo=62mmThicknesst=6mmPure torqueτ=7300N-mShear modulusG=73GPaLength of…
Q: Pls answer thank you! A 2 in diameter 6-spline shaft ( d= 0.85D, W= 0.25D, h= 0.075D ) and to slide…
A: Given DataDs=2inn=6d=0.85D=1.7inW=0.25D=0.5inh=0.075D=1.5inL=212inF=2500lbs
Q: Find the maximum stress developed in a stepped shaft when it is subjected to a: i) Torque of “T” Nm.…
A:
Q: A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 MPa. It is further…
A: Given, Diameter of shaft = d = 100 mm Axial stress = σa = 50 MPa Torque = T = 10 kNm = 10 x 106 Nmm…
Q: The rotation or twist in degrees of a shaft, 800 mm long subjected to a torque of 80 N-m, 20 mm in…
A:
Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 212 mm and a…
A:
Q: 35 mm 10 kN-m 2.36 x10° mm G, 50 GPa (1) C2 40 mm (2) 4.02 x10° mm A G2 = 25 GPa 2400 mm 3100 mm A…
A:
Q: II. If the permissible shear stress of a solid shaft is of 70 MPa, the torque angle between two…
A: a. Determine the required diameter in the function of the shear stress…
Q: A solid circular shaft needs to be designed to transmit a torque of 50Nm. If the allowable shear…
A: GIven DataT = 140 mPaFOS = 2T = 50 N.mTo find diameter
Q: The circular shaft AB consists of a 24.8 mm diameter solid steel cylinder in which a 11.6 mm…
A:
Q: A compound bar consists of a steel and bronze segment (Gs t= 80 GPa and Gbr = 40 GPa), The limiting…
A:
Q: For the indicated part. What would be the maximum torque that can be applied to the indicated part…
A: Torsional moment is applied across longitudinal axis the variations of which varies linearly and its…
Q: A single torque of T = 60 N.m is applied to a compound torsion member. Segment (1) is a 32-mm…
A:
Q: A single torque of T = 60 N.m is applied to a compound torsion member. Segment (1) is a 32-mm…
A: The angle of rotation: The angle at which the fixed end rotates with respect to the free end is…
Q: 1. Two torque as shown are applied on a compound shaft of aluminum segment and a steel. Determine…
A: Find the maximum permissible value of torque
Q: A single torque of T = 50 N-m is applied to a compound torsion member. Segment (1) is a 32-mm…
A:
Q: A motor drives a shaft at 12 Hz and delivers 20 kW of power as shown in Fig.4. (a) If the shaft has…
A:
Q: Consider a two-component rod fixed at the left end. The first component (on the left, positioned…
A:
Q: The shaft consists of a titanium alloy tube AB and a solid stainless steel shaft BC. Tube AB has a…
A:
Q: A hollow steel [G = 12,000 ksi] shaft with an outside diameter of 3.50 in. will be subjected to a…
A:
Q: Determine the torque that can be transmitted by this shaft. D = 120 mm d = 80 mm L = 3 m Modulus of…
A: outside dia (D) = 120 mm = 0.120 m inside dia (d) = 80 mm = 0.08 m length (L) = 3 m modulus of…
Q: A solid circular steel shaft having an outside diameter of 2.25 in. is subjected to a pure torque of…
A:
Q: Gears b and c have diameters of 10 cm and 4 cm, respectively. The maximum shear stress supported by…
A:
Q: A hollow steel shaft with an outside diameter of 76 mm and a wall thickness of 5 mm is subjected to…
A:
Q: A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to…
A:
Q: A solid circular steel shaft having an outside diameter of D = 1.00 in. is subjected to a pure…
A:
Q: A solid circular steel shaft having an outside diameter of 1.50 in. is subjected to a pure torque of…
A: Answer: The correct answer is option (b) i.e. 12.57 ksi.
Q: If a G1=77.2 GPa, G2 = 27 GPa, and torque of MT = 36 kN.m is applied to induce twisting in the…
A:
Q: A flanged bolt coupling consists of six 12.5 – mm steel bolts evenly spaced around a bolt circle 300…
A:
Q: A hollow nickel-steel shaft, whose outside diameter is twice the inside diameter, is to transmit…
A:
Q: An aluminum shaft with an outer diameter of 2 in and an inner diameter 1.5 in is fixed at one end.…
A:
Q: Consider two steel shafts CFG and HJ of diameters 50 mm and 70 mm respectively as shown in fig. The…
A:
Q: A hollow aluminium shaft of 80 mm outer diameter & 60 mm inner diameter is rotating @ 5 Hz when…
A:
A solid bar of circular cross section has a diameter of 40mm and length of 1300mm. G=80GPa and torque applied at both ends is 340 N.m. Determine the angle of rotation in radians.
Trending now
This is a popular solution!
Step by step
Solved in 2 steps with 1 images
- .17 A mountain-bike rider going uphill applies torque T = Fd(F = l5lb, d = 4 in.) to the end of the handlebars ABCD by pulling on the handlebar extenders DE. Consider the right half of the handlebar assembly only (assume the bars are fixed at the fork at A). Segments AB and CD are prismatic with lengths L, = 2 in.andL3 = 8.5 in, and with outer diameters and thicknesses d01 = 1.25 in. 101 = 0.125 in. and d03 = O.87in.,i03 = 0.ll5in, respectively as shown. Segment BC’ of length L, = 1.2 in. however. is tapered, and outer diameter and thickness vary linearly between dimensions at B and C. Consider torsion effects only. Assume G = 4000 ksi is constant. Derive an integral expression for the angle of twist of half of the handlebar tube when it is subjected to torque T = Fd acting at the end. Evaluate ‘b1-, for the given numerical1ues.A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).A stepped shaft ABC consisting of two solid, circular segments is subjected to uniformly distributed torque t1acting aver segment 1 and concentrated torque t2applied at C, as shown in the figure. Segment 1 of the shaft has a diameter of d1= 57 mm and length of L1= 0.75 m; segment 2 has a diameter d2— 44 mm and length L2= 0.5 m. Torque intensity /,"= 3100 N . m/m and T2= 1100 N. m. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: .x = L1/2 and at .x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams.
- Two sections of steel drill pipe, joined by bolted flange plates at B, arc subjected to a concentrated torque 4000 kip-in. at x = 3 ft, and a uniformly distributed torque t0= 50 kip-ft/ft is applied on pipe BC. Let G = 11,800 ksi and assume that pipes AB and BC have the same inner diameter, d = 12 in. Pipe AB has a thickness tAB= 3/4 in., and pipe BC has a thickness tBC= 5/8 in. Find the reactive torques at A and C and the maximum shear stresses in each segment.A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.A tapered bar AB with a solid circular cross section is twisted by torques T = 36,000 lb-in. (sec figure). The diameter of the bar varies linearly from dAat the left-hand end to dBat the right-hand end. The bar has length L = 4,0 ft and is made of an aluminum alloy having shear modulus of elasticity G = 3.9 × 106 psi. The allowable shear stress in the bar is 15,000 psi and the allowable angle of twist is 3.0°. If the diameter at end B is 1.5 times the diameter at end A, what is the minimum required diameter dAat end A?
- A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
- A nonprismatic bar ABC with a solid circular cross section is loaded by distributed torques (sec figure). The intensity of the torques, that is, the torque per unit distance, is denoted t(x) and varies linearly from zero at A to a maximum value T0/L at B. Segment BC has linearly distributed torque of intensity r(x) = T0/3L of opposite sign to that applied along AB. Also, the polar moment of inertia of AB is twice that of BC and the shear modulus of elasticity of the material is G. Find the reaction torque RA. Find internal torsional moments T(x) in segments AB and BC. Find the rotation t0 Find the maximum shear stress tmaxand its location along the bar, Draw the torsional moment diagram (TMD:T(x),0 < x < L).A circular tube AB is fixed at one end and free at the other. The tube is subjected to concentrated torques as shown in the figure. If the outer radius of the tube is 1.5 in, and the thickness is 3/4 in., calculate the strain energy stored in the tube. Let G= 11,800 ksi.A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?