A single torque of T = 60 N.m is applied to a compound torsion member. Segment (1) is a 32-mm diameter solid brass (G = 37 %3D GPa) rod. Segment (2) is a solid aluminum (G = 26 GPa) rod. Determine the minimum diameter of the aluminum segment if the rotation angle at C relative to support A must not exceed 5°. T= 60 N.m (1) (2) C 1,800 mm 800 mm Select one: a. 21.55 mm b. 10.77 mm c. 11.88 mm d. 23.77 mm O e. 32.00 mm f None

A single torque of T = 60 N.m is applied to a compound torsion member. Segment (1) is a 32-mm diameter solid brass (G = 37 %3D GPa) rod. Segment (2) is a solid aluminum (G = 26 GPa) rod. Determine the minimum diameter of the aluminum segment if the rotation angle at C relative to support A must not exceed 5°. T= 60 N.m (1) (2) C 1,800 mm 800 mm Select one: a. 21.55 mm b. 10.77 mm c. 11.88 mm d. 23.77 mm O e. 32.00 mm f None

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The shaft shown below consists of three segments AB, BC and CD is subjected to the three torques T1=114 N.m, T2=245 N.m and T3=441 N N.m. The length of each segment is L1=0.71 m, L2=0.31 m and L3=0.43 m . The diameter of each segment is d1=46 mm, d2=97 mm and d3=131 mm . The material have modulus of rigidity G = 143 Gpa. Answer the following questions
A solid bar of circular cross section has a diameter of 40mm and length of 1300mm. G=80GPa and torque applied at both ends is 340 N.m. Determine the angle of rotation in radians.
Two sections of steel drill pipe, joined by boltedflange plates at B, are being tested to assess the adequacyof both the pipes. In the test, the pipe structureis fixed at A, a concentrated torque of 500 kN ? m isapplied at x = 0.5 m, and uniformly distributed torqueintensity t0 = 250 kN . m/m is applied on pipe BC.Both pipes have the same inner diameter d = 200 mm.Pipe AB has thickness tAB =15 mm, while pipe BChas thickness tBC =12 mm. Find the maximum shearstress and maximum twist of the pipe and their locationsalong the pipe. Assume G = 75 GPa.
A shaft when subjected to pure torsion developed a stress of 50 Mpa. If polar moment of inertia is 6.1359 x 10 -7 m4 , determine the maximum torque the shaft could handle. A. 1.23 KN.m B. 1.68 KN.m C. 1.84 KN.m D. 2.48 KN.m
The two shafts are made of steel (G=11x106 lb/in2). Each has a diameter of 1 in. , and they are supported by bearings at A, B and C, which allow free rotation. If the support at D is fixed, determine the angle of twist of end A when the torques are applied to the assembly as shown. Torque applied at H of 80 ft lbs, and at G of 40 ft lbs in opposing directions as seen in the figure
The mean dimensions of the cross-section of the leading edge and torsion box of an airplane wing can be approximated as shown. If the wing is made of 2014-T6 (G = 19 GPa) aluminum alloy having an allowable shear stress of Tallow = 158 MPa, and the wall thickness is 12 mm. Determine the maximum allowable torque and the corresponding angle of twist per meter length of the wing.
The shaft consists of three concentric tubes, each made from the same material and having inner and outer radii as given below. Length of shaft is 2m. One end is fixed to the wall and to the other end a disc is attached. If a torque of T =800 N.m is applied at the disc end, determine the maximum shear stress in the shaft. 1. Inner tube: r; = 20mm, r, = 25 mm 2. Center tube: r; = 26 mm, r. = 30 mm 3. Outer tube: r = 32mm, r, = 38mm
2: If the permissible shear stress of a solid shaft is of 70MPa, the torque angle between two cross sections separated 2.5m does not exceed 3°, the applied torque is of 1400N.m and G=11Gpa a. Determine the required diameter in function of the shear stress b. Determine the required diameter in function of the angle of twist
The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. the allowable shear stresses for the magnesium and steel sre Tallow mg =45Mpa ve Tallow st=72MPa, respectively. The shear modulus of elasticity for Am1004-T61magnesium alloy is 18Gpa and for A-36 steel is 75Gpa. a)Determine the maximum allowable torque that can be applied at A. b)Find the corresponding angle of twist of end A.
The solid steel rod (1) has an allowable shear stress of 12 ksi. The brass tube (2) has an allowable shear stress of 5 ksi. The diameter of the rod is d1 = 0.625 in. The outside diameter of the tube is D2 = 1.625 in., and its wall thickness is t2 = 0.125 in. The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at B. Determine the largest torque Tmax that can be applied at the upper end of the steel rod.
A solid circular steel shaft having an outside diameter of 1.50 in. is subjected to a pure torque of T = 8330 lb-in. The shear modulus of the steel is G = 12,000 ksi. Determine the maximum shear stress in the shaft. a. 7.64 ksi b. 12.57 ksi c. 13.20 ksi d. 10.33 ksi e. 15.86 ksi
Determine the power in kilowatts transmitted by the solid shaft if the radius is 7.5mm and it rotates with revolution of 67.6 RPS. Maximum torsional stress equivalent to 50000 kPa.