A solid circular column (one end is fixed, the other end is free) is made from an alloy with a Young's Modulus (E) = 73 GPA. The length of the column is 740 mm. Calculate the minimum acceptable diameter in millimeters that will prevent buckling if the applied load is 97 kN.

A solid circular column (one end is fixed, the other end is free) is made from an alloy with a Young's Modulus (E) = 73 GPA. The length of the column is 740 mm. Calculate the minimum acceptable diameter in millimeters that will prevent buckling if the applied load is 97 kN.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.4.3P: An aluminum pipe column (E = 10,400 ksi) with a length L = 10.0 ft has inside and outside diameters...

See similar textbooks

Related questions

Q: A circular metal column is to support load of 500 Tonne and it must not compress more than 0.1 mm.…

Q: Problem 1.16. Find the modulus of elasticity for a rod, which tapers uniformly from 30 mm to 15 mm…

Q: A circular hollow column has an external diameter of 1.5 m and a wall thickness of 0.25 m. Both ends…

A: Given: Diameter, d = 1.5 m Length, l = 20.8 m E = 200 GPa Find: The…

Q: Both ends of the fixed (fixed) rod were mounted at 0 °C. Calculate the minimum diameter of the bar…

Q: Question 4. A hollow steel tube 5 m long with external and internal diameters 100 mm and 80 mm…

A: GIVEN DATA LOAD P=150KN LENGTH L=5m OUTER DIA=100mm INNER DIA=80mm CHANGE IN LENGTH =6.4mm FOS=4

Q: 15 in 05 im 24 in The machine link shown is subjected to an axial load P, as shown. The link is…

Q: Question 2 5 Points An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads…

Q: )Describe 4 assumptions in the Euler theory of buckling. b)Euler theory does not take into…

A: Euler's theory of column buckling is used to estimate the critical load of the column when the…

Q: To use deformation compatibility equations to calculate loads and deflections for statically…

A: Free Body diagram: Taking moment about F2 ∑MF2 = 0-F1(L1+L2)-P(L2) = 0F1 =…

Q: A 11-m uniform beam is hinged to a vertical wall and held horizontally by a 5.0-m cable attached to…

Q: The pin-connected structure consists of two cold-rolled steel [E = 28,000 ksi] bars (1) and a bronze…

Q: Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 16 in. and…

Q: Select the lightest W shape that will act as a column 8 m long with hinged ends and support an axial…

A: Given Load, F = 270 kN Stress = 200 MPa Length, L = 8 m Find Lightest W shape

Q: 7. A SAE steel column has a circular cross-section of 16 mm in diameter and a length of 320 mm. The…

Q: A slender bar AB with pinned ends andlength L is held between immovable supports (seefigure).What…

A: Given L = length A = cross-sectional area I = moment of inertia E = modulus of elasticity…

Q: Determine the critical axial buckling load for an 8 3/4 x 12 inches glue-laminated column braced at…

A: In the question , given that, E = young modulus of elasticity (1.8×106psi) dimension of column ,…

Q: A circular-cross-section bar with a diameter of 50 mm and a length of 1.25 m is axially loaded. The…

A: For the above problem we calculate the transitional slenderness ratio whose value decides which…

Q: The column in Fig. is made of aluminum alloy 2014-T6 and is used tosupport an eccentric load P.…

A: The expression for the radius of gyration is: The slenderness ratio for the column is: Here, K…

Q: 2) Determine the critical axial buckling load for an 8 % x 12 in glu-laminated column braced at 10…

A: For 834*12 inA=105.00 in2Iy=1260.00 in4, ry=3.5 inIZ=669.922 in4, rZ=2.5 inThe total height=L=…

Q: 03-H14 aluminium alloy is subjected to a 6-kN tensile rod diameter. Calculate the diameter if this…

Q: load of 200 KN. If the length of the bar is 2 m and E = 200 GPa. What will be the elongation of the…

Q: If you double the length of a column by what factor is it buckling load

A: Given data Double the length of a column

Q: Part A The two bars shown in the figure below (Eigure 1) are made of a material that has the…

Q: A 51 mm diameter steel rod (E = 207 GPA) with pinned end conditions is to be subjected to an axail…

A: Given Diameter, d = 51 mm E = 207 GPa Find Maximum length, L

Q: An aluminum tube of length 0.01R (m) is used as column (fixed at both ends) carrying an axial load…

A: Given data:-Length, L=0.01R=0.01×993=9.93mAxial load, P=1.333R=1.333×993=1323.669NOuter diameter of…

Q: A solid round steel rod with Sy 350 MPa is 945 mm long and 62 mm in diameter. With a safety factor…

A: Given Length, L = 945 mm Diameter, d = 62 mm Yield…

Q: An alloy bar 800 mm long and 200 mm in cross-section is held between two rigid plates and is…

A: Given:- Axial load=200kn Cross-sectional area:-200mm2 To find:- Reaction forces at end and…

Q: A column is axially loaded in compression. The ends were specified to be fixed, but because of a…

A: (a) when column one end fixed and other end pinned then buckling load due to compressive force…

Q: 3. Two columns A C and BC have a circular cross section of radius 5 cm, yield strength oY=100 MPa,…

A: Given: Load P=100kN Diameter of the links=0.05×2=0.1m E=100GPa

Q: Determine the critical load, Per, required to cause failure of a 21 ft long column made of A-36…

A: Given data as per question Moment inertia of column in xx axis = 2.10 in4 Moment inertia of column…

Q: For a solid cylindrical steel structure with length of 1.5 meters that is expected to withstand a…

Q: The link shown, made of AISI C1045 steel, as rolled, is subjected to a tensile load of 8000 Ib. Let…

A: The material given is AISI C1045 steel. The tensile load is F=8000 lb. The properties of material…

Q: Derive a formula for the total elongation (8) of the bar due to the load P a A

A: Given :- Derive the formula for total elongation

Q: Problem 2: A circular rod tapers in diameter from 50 mm from one end to 20 mmon theother end for a…

Q: A. Explain briefly what you understand by the following terms I) strut II) column B. Distinguish…

Q: Determine the critical axial buckling load for an 8 ¾ x 12 in. glu-laminated column braced at 10 ft…

A: Given, Young's modulus of elasticity, E=1.8× 106 psi Moment of inertia, I=b h312I=12×…

Q: Find the critical buckling load of the 7 m long, cross-section column made of A-36 steel with hinged…

A: Given: The length of column, L = 7 m The modulus of elasticity, E = 200 GPa The outer diameter of…

Q: A round vertical bar is clamped at the lower end and is free at the other. The effective length is 2…

A: Given data,P=30 Nl=2mδ=15mmPe=Buckling loadle=effective length

Q: Consider the steel truss and member cross-section presented in figures below. All the members of the…

Q: A steel bar 50 mm in diameter and 2 m long is surrounded by a shell of a cast iron 5 mm thick.…

Q: Two columns are of equal length, equal supporting conditions, made of the same material, but of…

A: Euler's theory for Buckling failure: It is derived a formula for stability of long column.According…

Question

100%

A solid circular column (one end is fixed, the other end is free) is made from an alloy with a Young's Modulus (E) = 73 GPA.
The length of the column is 740 mm. Calculate the minimum acceptable diameter in millimeters that will prevent buckling if
the applied load is 97 kN.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A fixed-end column with circular cross section is acted on by compressive axial load P. The IS-ft-long-column has an outer diameter of 5 in., a thickness of 0.5 in., and is made of aluminum with a modulus of elasticity of 10,000 ksi. Find the buckling load of the column.
An aluminum pipe column (E = 10,400 ksi) with a length L = 10.0 ft has inside and outside diameters d1= 5.0 in. and d2= 6.0 in., respectively (sec figure). The column is supported only at the ends and may buckle in any direction. Calculate the critical load Pcrfor the following end conditions: (a) pinned-pinned, (b) fixed-free, (c) fixed-pinned, and (d) fixed-fixed.
A real rectangular steel bar supports a concentric load of 58.5kN. Both ends are fixed. If the modulus of elasticity is 210 GPa, what is the maximum length the rod can be without experiencing buckling failure? Assume the effective length factor, K, is 0.65.
To support a tensile load of 65 kN, a metallic rod with a circular cross section and a length of 0.32 m will be used. It is required that the tension in the bar does not exceed 240 MPa and the maximum elongation is 0.42 mm. What is the minimum rod diameter [m] in these conditions? (Elasticity for metallic bar take the module as 220 GPa).
Derive the Euler Buckling formula for column having fixed support at both ends. (eXPLAIN IN DETAIL IN HAND WRITTEN )
For a solid cylindrical steel structure with length of 1.5 meters that is expected to withstand a buckling load of 200 kN, calculate its diameter based on the Euler formula for the cases of pinned-pinned, pinned-fixed and fixed-fixed ends.
A column consists of a 2.5 m long hollow tube with an outside diameter equal to 1.5 times that of the inside diameter. The column must carry an axial load of 40 KN without buckling. Use a factor of safety of 5 and calculate the dimensions of the tube if one end is fixed and the other end is free. Use the Euler formula and take ?=200 ???.
An axial load of 100 kN is applied to a flat bar 20 mm thick, tapering in width from 120 mm to 40 mm in a length 0f 10 m. Assuming E=200 GPa, determine the total elongation of the bar.
Determine the critical axial buckling load for an 8 3/4 x 12 inches glue-laminated column braced at 10ft from the bottom in the y axis for a total height of 25ft. Assume pin connections at top and bottom. Fc= 1750 psi, E= 1.8x106 psi. (Western cross-section glu-lam data is in the text).
A cylindrical column made of 304 stainless steel and 3m high must support a load of 1000kg. It is recessed in the ground and free in the upper end. a) Calculate the compressive stress, then the minimum diameter of the column to respect a safety factor of 3 on the elastic limit. Answer for a) = Compressive stress = 86.78 MPa b. Given the nature of this installation, this column is at risk of buckling. Calculate again the minimum diameter necessary to respect a factor of safety of 3 on the critical constraint.
A. Explain briefly what you understand by the following terms I) strut II) column B. Distinguish between long and short column C)a hollow alloy 5000mm long with external and internal diameter of 50mm and 25mm respectively is used as a column with one end fixed and the other end hinged.Determine the buckling load by Euler's formula.Take Young modulus of elasticity as 180GN/m^2.
Rigid bar ABC is supported by pin-connected bar (1). Bar (1) is 2.0-in. wide, 1.00-in. thick, and made of aluminum that has anelastic modulus of E = 12,000 ksi. Determine the maximum magnitude of load P that can be applied to the rigid bar withoutcausing member (1) to buckle