A student prepared a compound. the melting point of the crude the product was 42 to 48 degree C. after purifying the solid for the first time, the melting point was 47 to 51 degree C. after another purification, the melting point was 50 to 53 degree C. at this stage, can the student confidently say the product has been completely purified?

A student prepared a compound. the melting point of the crude the product was 42 to 48 degree C. after purifying the solid for the first time, the melting point was 47 to 51 degree C. after another purification, the melting point was 50 to 53 degree C. at this stage, can the student confidently say the product has been completely purified?

EBK A SMALL SCALE APPROACH TO ORGANIC L

4th Edition

ISBN:9781305446021

Author:Lampman

Publisher:Lampman

Chapter13: Isolation Of Eugenol From Clov

Section: Chapter Questions

Problem 9Q

See similar textbooks

Similar questions

Draw a schematic diagram using this information. Preparation of the solution Take about 25-30 ml of distilled water in a beaker and add powdered crude copper sulphate while stirring the solution so that the powder dissolves. Keep adding the powdered sample till a little of it remains undissolved, even if it is stirred thoroughly. Now add 2-3 ml of dil. H2SO4 to make the solution clear. This prevents the hydrolysis of copper sulphate. Filtration of the solution Take a funnel and fix a filter paper in it and clamp it to a stand. Place a china dish under the funnel. The stem of the funnel should touch the wall of the china dish to avoid the solution splashing out. Pour the solution into the funnel over a glass rod and collect the filtrate in a china dish. The insoluble impurities are left in the filter paper as residue. Concentration of the filtrate to crystallisation point Heat the china dish on a sand bath till the solution is reduced to about one-third of its original volume. To…
A student performs a crystallization on an impure sample of biphenyl. The sample weighs 0.5 g and contains about 5% impurity. Based on his knowledge of solubility, the student decides to use benzene as the solvent. After crystallization, the crystals are dried and the nal weight is found to be 0.02 g. Assume that all steps in the crystallization are performed correctly, there are no spills, and the student lost very little solid on any glassware or in any of the transfers. Why is the recovery so low?
Consider a 1.000-L stock solution of 9.69 M Na3PO4. A 2.000-mL aliquot is taken from this stock solution and diluted to a final volume of 1.000 L. A 5.000-mL aliquot is then taken from this new solution and further diluted to make a new solution with a final volume of 750.0 mL. Calculate Na+ in the final solution.
You are given a concentrated stock solution of 3.0 M sucrose, and you’re asked to do a serial dilution of 1:25, 1:10, and 1:5. What is the final concentration of sucrose (in mM) you achieve after these dilutions. Show your unit conversions step by step
To determine the amount of copper and the identity of the copper compound in the unknown sample, a 100-mL solution containing 120.8 mg of the sample was initially prepared. Then, 5.00 mL of this solution was pipetted and diluted with deionized water in another 100-mL volumetric flask. If the concentration of copper in the 5mL solution is 18mg/L, what is the: (1) mass of copper in the 5ml solution? (2) mass of copper in the unknown sample?
A mixture must be at its saturation point to be classified as a true solution. True False
Which is not required in recrystallization? a. solution is filtered at high temperature b. moderate volatility solvent c. saturated solution d. solvent must dissolve the impurities
Chemistry A group of students was tasked with synthesizing dibenzalacetone (DBA) in the lab. They used acetone as limiting reagent, calculated their TY to be 8.0 g DBA, obtained 14.0 g crude product (wet) and their % Yield was 65%. What was the actual yield for their final product (recrystallized, dry DBA)? What was the minimum volume (ml) of ethanol they needed to recrystallize their wet crude? What was the amount of impurities (side products, moisture,...) contained in their wet crude?
When purifying a sample of aspirin that was produced in the lab, the impure aspirin sample should be dissolved in a very cold solvent, so that solid impurities can be filtered and analyzed the next day or the next week. True or False?
A student has a mixture of two possible compounds. The student performs recrystallization to separate the two compounds. The student decides to identify the separated compound by melting point. The student’s compound has a melting range of 108-109 °C using a ramp rate of 2°C/min. The student’s partner believes that they isolated compound 2, while the student thinks they have compound 1. Choose the best answer to go with this scenario. Compound 1 Literature Melting point: 111 °C Compound 2 Literature Melting point: 104 °C A) It is correct that they definitely have compound 2. B)The students have neither of the two compounds. C) The ramp rate is too high so the experimental melting range is not accurate. D) The students likely have compound 2, but should do a mixed melting range experiment with a standard of compound 2 to be certain. E) They did not separate the compounds properly, and it is still a mixture. F) The students likely have compound 1, but should do a mixed melting range…
During a laboratory experiment, a student mixed two homogeneous aqueous solutions. After mixing a solid precipitate was formed. What is the best way for the solid to be separated from the solution? Put it in a beaker and heat it. Filter it using a Buchner funnel, filter flask and vacuum pump. Use a pipette to remove the solid from the liquid. Scoop it out with a spatula. The solid cannot be isolated.
Calculate the concentration of sugar in this solution using the volume percent equation. For the purpose of this exercise, it can be assumed that the weight of the drink mix is 0.00 g. The volume of the solution is 3 and 1/3 cups. Calculate and record the volume percent (g/mL). (Note that 1 cup = 236 mL). Volume %=Volume of Solute / Volume of Solution ×100% I used 1/2 cup of granulated sugar and 1/2 tsp of the drink mix, and 3 cups of water. 2. Calculate the concentration of each diluted solution using the equation below and the volumes in Table. C1V1=C2V2 Where: C1=concentration of stock solution V1=volume of stock solution C2=concentration of diluted solution V2=volume of diluted solution (This is all the information that I have)