A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1/2 inch. the gage lenght ( the lenght over which the elongation is measured ) is 2 inches. for a load 13.5 kips, the elongation was 4.66x10^-3 inches. if the load is assumed to be with in the linear elastic range of the material , determine the modulus of elasticity

A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1/2 inch. the gage lenght ( the lenght over which the elongation is measured ) is 2 inches. for a load 13.5 kips, the elongation was 4.66x10^-3 inches. if the load is assumed to be with in the linear elastic range of the material , determine the modulus of elasticity

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.2P: A tensile test was performed on a metal specimen having a circular cross section with a diameter of...

See similar textbooks

Similar questions

The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
To stretch a 200 mm long tensile test specimen (a) of steel elastically by 0.08 mm. How many loads do I need to apply? (b) What is the maximum length of this sample without plastic deformation? How long can it be extended? (The modulus of elasticity of steel is 210 GPa, yield strength 580 MPa, tensile strength 920 MPa specified as.
A tensile test was performed on a metal specimen with a diameter of 1⁄2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The data were plotted on a load-displacement graph, P vs. ∆L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P y∆L 5 1392 kips yin. What is the modulus of elasticity?
The data shown in the table were obtained from a tensile test of a metal specimen with a rectangular cross-section of 0.2 in.^2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches.
A steel rod, 12mm in diameter and 150mm long was subjected to a tensile test. After the test, the length increases to 150.40mm. The material remains within the linear elastic region and its modulus of elasticity is 200,000 MPa. Determine the force, in Newton (N), applied to the test.
The data shown in the table were obtained from a tensile test of a metal specimen with a rectangular cross-section of 0.2 in.? in area and a gage length (the length over which the elongation is measured) of 2.000 inches. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2% offset method to determine the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 0.510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are shown in Table 1.1.a. Prepare a table of stress and strainb. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them.c. Determine the modulus of elasticity as the slope of the best-fit lineLoad (Ib)Strain × 106 (in./in.)0025037.150070.31000129.11500230.12000259.42500372.43000457.73500586.5
A steel rod, 12mm in diameter and 150mm long was subjected to a tensile test. After the test, the length increases to 150.40mm. The material remains within the linear elastic region and its modulus of elasticity is 200,000 MPa. Determine the force, in Newton (N), applied to the test. different solution please
In a simple tensile test using a cylindrical test specimen (Dia.=10mm), the applied force was 120 kN and the extension was 2%. Find the modulus of elasticity of that specimen. If the standard modulus of elasticity is 200 GPa, is this material accepted or not? and why?
Consider a cylindrical metal 6 mm in diameter and 50 mm long ispulled in tension. It is known that yield strength and elastic (Young’s) Modulus of thematerial are 200 MPa and 100 GPa, respectively, and its Poisson’s Ratio is 0.3.(a) Determine whether the deformation is elastic or plastic when 6000 N is applied.(b) Calculate specimen elongation (∆l) and reduction in diameter (∆d) when 5000 N isapplied? What are the values ∆l and ∆d when the load is released?(c) If necking occurs at a load of 8850 N, determine the UTS of the metal.(d) Calculate the ductility in terms of % E.L. if the length of the specimen at fracturepoint is 56.0 mm.