Phase DiagramA/ The lead and tin are partially dissolved in each other in solid state although they completely dissolvedin liguid state. They form eutectic from solid solutions alfa (a) and beta (B) at alloying composition 62% tinand 38% lead, the eutectic forming temperature is 184oC. Alfa contained 20% tin dissolved in 80% lead at1840C while beta consist of lead dissolved in tin at 1840C. If the 100 g of eutectic contained 45.5 g of alfaat 1840C. The melting temperatures of lead and tin are 3290C and 2320C respectively, and the solubility oftin and lead in each other's diminished to zero at room temperature. Plot the phase diagram for lead- tinsystem label all phases and temperature. Show graphically the temperature of the formation of the firstsolid for 42% lead alloy

The lead melting point, TPb = 329°C The tin melting point, TSn = 232°C The mass of α at eutectic…

Answered: A/ The lead and tin are partially…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Use the phase diagrams for Cu-Ni and Cu-Ag systems below to answer the question: Based on the mechanism, would you expect a solution containing 80 wt% Cu to be stronger if the remaining 20% of the alloy was Ni or Ag? Briefly explain
Consider the magnesium oxide-aluminum oxide phase diagram; ss indicates a solid solution. The radii of Mg2 + and Al3 + are 0.072 and 0.053 nm, respectively. (a) There are two eutectic reactions on the diagram; describe them (temperatures, compositions and phases). (b) Spinel, at temperatures below 1000 °C, is a compound with a composition of 50 mol% Al2O3-50 mol% MgO. For higher temperatures, spinel is stable for a range of compositions. What is the temperature of the congruent fusion? (c) What are the main reasons for the low solubility of Al2O3 in MgO below 1400 °C? (d) Maximum non-stoichiometry on the Al2O3-rich side, in the spinel phase field, occurs approximately 2000 °C and corresponds to approximately 82 mol% (92% w) of Al2O3. Determine the type of gaps defect that is produced and the percentage of gaps that exists in this composition.
For a steel with a 0.2 wt%C, what is the mass fraction and composition of phases at 600 (Please draw connections on the graph)
a-Arrange in a table the number of phases that can be observed at R.T in the range starting from zero to 6.67%C in an "Equilibrium Phase Diagram" and the corresponding three of the mechanical properties.b- Explain with examples the solid-solution, eutectic and peritectic observed phases.c- Draw the .microstructure of each phase
BINARY PHASE DIAGRAMS Please only answer parts d and e as the rest have been solved. Show full detailed explanation to answers with diagrams if necessary a)(i) What is the melting point of pure Mg?(ii) What is the maximum solubility of Mg in Pb and at what temperaturedoes this occur? (b) A 50 wt.% Pb-50wt% Mg alloy is slowly cooled from 700 °C to 400 °C.(i) At what temperature does the first solid phase form?(ii) What is the composition of this solid phase?(iii) At what temperature does all the liquid solidify?(iv) What is the composition of the last remaining liquid phase?(v) What is the freezing range? (c) What is the mass fraction of solid and liquid of a 60 wt.% Mg alloy at atemperature of 500 °C.(d) Draw and label the microstructure of an 80 wt.% Mg alloy at 600 °C.(e) A Mg-Pb alloy of mass 5.5 kg has a composition just slightly below thesolubility limit of 200 °C.(i) What mass of lead is in the alloy?(ii) If the alloy is heated to 350 °C how much more lead can be dissolvedin…
Using the Al−Cu phase diagram in (b), what is the amount of θ phase (in %) that would precipitate at the grain boundaries in the equilibrium microstructure after slow cooling shown in (a)?
1-The microstructural design of Iron-Carbon(Fe-C) alloys has led to the development of vast range of steels for structural material applications. The phase diagram provide means for producing specific microstructures. Using the phase diagram below to answer the following questions A – If the liquid mixture of Fe-3%Wt C is slowly cooled from 1600 C to 1200C indicate the phase(S) that are present at 1200 C . Also calculate the composition of the of phases.(10) B-Describe the sequence of all phase transformation that accour from Fe-1.5%wt C is slowly cooled from 1600 C to 400 C. Use the diagram below to to describe the microstructures for each phase transformation (10)
According to the binary eutectic Pb-Sn phase diagram for the alloy of having 25 wt% Sn at 200°C determine the phase weight fractions.
Phase Diagrams: You are given the lead tin (Pb-Sn) phase diagram. Below the eutectic isotherm is identified as the two phase region a + B. a) At 30wt % Sn, in the circles below draw the microscopic observations evolving at 3000C, 2250C, and 1000C for this hypoeutectic alloy. b) At a temperature just above the isotherm at 1830C, for the 30 wt% Sn Alloy, calculate the fractions of each phase present at equilibrium and the corresponding composition of each phase.
Consider the binary eutectic copper-silver phase diagram shown below. Make phase analysis of a 80 wt % Ag–20 wt% Cu alloy at the temperatures (a) 900°C, and (b) 780°C-ΔT. In the phase analysis include: (I) phases present, (ii) chemical compositions of phases, (iii) mass fractions of phases, and (iv) sketch of microstructure.
Copper-Nickel alloy is widely applied in industry. (a) List at least three applications where Cu-Ni alloy is used; (b) How many components and phases are shown in the below phase diagram? (c) For a mixture of 40 wt% Cu and 60 wt% Ni at 1320 oC, what phases are present? Identify theamount of these phases by applying “lever rule”.
For a 60-40 Pb-Sn alloy, what would the percent of each phase be at 185°C and 180°C?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS