A three-phase transmission line, 10 km long delivers a load of 5000 kW at 11 kV and 0.8 pf lagging atthe receiving end. The resistance of the line per km per phase is 0.1 2 and the reactance per phase perkm is 0.2 2. Solve for the sending end voltage of the line, total current and voltage regulation of theline. Present also the transmission line modeling.

Type of Transmission line Short Transmission line ( upto 80 Km) Medium Transmission line (80 to…

A three-phase transmission line, 10 km long delivers a load of 5000 kW at 11 kV and 0.8 pf lagging at the receiving end. The resistance of the line per km per phase is 0.1 Q and the reactance per phase per km is 0.2 2. Solve for the sending end voltage of the line, total current and voltage regulation of the line. Present also the transmission line modeling.

A three-phase transmission line, 10 km long delivers a load of 5000 kW at 11 kV and 0.8 pf lagging at the receiving end. The resistance of the line per km per phase is 0.1 Q and the reactance per phase per km is 0.2 2. Solve for the sending end voltage of the line, total current and voltage regulation of the line. Present also the transmission line modeling.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.25P

See similar textbooks

Similar questions

A 40-km, 220-kV, 60-Hz, three-phase overhead transmission line has a per-phase resistance of 0.15/km, a per-phase inductance of 1.3263 mH/km, and negligible shunt capacitance. Using the short line model, find the sending-end voltage, voltage regulation, sending-end power, and transmission line efficiency when the line is supplying a three-phase load of (a) 381 MVA at 0.8 power factor lagging and at 220 kV and (b) 381 MVA at 0.8 power factor leading and at 220 kV.
Consider a long radial line terminated in its characteristic impedance Zc. Determine the following: (a) V1/I1, known as the driving point impedance. (b) | V2 |/V1|, known as the voltage gain, in terms of al. (c) | I2 |/| I1 |, known as the current gain, in terms of al. (d) The complex power gain, S21/S12, in terms of al. (e) The real power efficiency, (P21/P12)=, terms of al. Note: 1 refers to sending end and 2 refers to receiving end. (S21) is the complex power received at 2; S12 is sent from 1.
A single-phase overhead transmission line consists of two solid aluminum conductors having a radius of 3 cm with a spacing 3.5 m between centers. (a) Determine the total line inductance in mH/m. (b) Given the operating frequency to be 60 Hz, find the total inductive reactance of the line in /km and in/mi. (c) If the spacing is doubled to 7 m, how does the reactance change?
A 50ohm transmission line powered by a 3GHz source and terminated with a load impedance ZL=25-j60 ohms will be matched with the shorted parallel side. What should be the length, in m, of the parallel lateral line calculated using the Smith diagram ?
For a given short transmission line of impedance R+jX ohms/phase, the sendingend and receiving end voltages Vs and Vr are fixed. Derive the expression for themaximum power that can be transmitted over the line.
A short 3 phase transmission line, connected to a 33kV, 50 Hz generating station at the sending end is required to supply a load of 10Megawatts at 0.8 power factor lagging, 30kV at the receiving end. If the minimum transmission line efficiency is to be limited to 96%, estimate the per phase values of resistance and inductance of the line.
A short three phase transmission line of parameters R-0.4Ω and X=0.4Ω is delivering 2000kVA to a load at a pf of 0.8 lagging at the receiving enf=d of the line.if the load voltage is 3000 V, determine the voltage regulation and efficiency of the line.
A balanced load of 30 MW is supplied at 132 kV, 50 Hz and 0•85 p.f. lagging by means of a transmission line. The series impedance of a single conductor is (20 + j52) ohms and the total phases-neutral admittance is 315 microsiemens. Shunt leakage may be neglected. Using the nominal T approximation, calculate the line voltage at the sending end of the line. If the load is removed and the sending end voltage remains constant, find the percentage rise in voltage at the receiving end.
A balanced load of 30MW is supplied at 132 kV, 50Hz and 0.85 p.f. lagging by means of a transmission line. The series impedance of a single conductor is (20+j 52) ohms and the total phase-neutral admittance is 315 micro mho. Shunt leakage may be neglected. Using the nominal T and π approximation, calculate the line voltage at the sending end of the line. If the load is removed and the sending end voltage remains constant, find the percentage rise in the voltage at the receiving end.
1/In the Transmission Line Simulator, the Transmission Line is connected in Nominal-Pi Circuit. Select one: True False
transmission line with an impedance of 35 Ω is connected to a load of impedance of 300 Ω, then the value of VSWR assuming that the line impedance is decreased by 30 % and load impedance is increased by 40%.
In the power system whose single line diagram is shown below, the line cross section is 95 mm2, the intrinsic conductivity coefficient is 34m/ohm.mm2 and the inductive reactance of the line is given as 0.4 ohm/km. According to these values; a) Calculate the active, reactive and visible components of the currents passing through each line segment.b) Find the location and value of the largest voltage drop.