A tube is used to fill a tank of volume 37.854 L. (1L = 0.001m3). The diameter of the tube is 2 cm, and it reduces to 0.8 cm at the tube exit. If it takes 50 s to fill the tank with water, If the water density is 1kg/L, the volume and mass flow rates of water through the hose are respectively

A tube is used to fill a tank of volume 37.854 L. (1L = 0.001m3). The diameter of the tube is 2 cm, and it reduces to 0.8 cm at the tube exit. If it takes 50 s to fill the tank with water, If the water density is 1kg/L, the volume and mass flow rates of water through the hose are respectively

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water at 60 deg. F is pumped from a reservoir to the top of a mountain through a 6-in SCH 120 pipe at an average velocity of 12 ft/s. The pipe discharges into the atmosphere at a level 3000 ft above the level in the reservoir. The pipeline itself is 4500 ft. long. If the overall efficiency of the pump and the motor driving it is 70% and the cost of electric energy to the motor is 4 cents per kilowatt-hour, 2. what is the theoretical power consumption in hp? 373755575557337733none of the given
A fan draws 2.42 m^3 per second of air at a static pressure of 2.54 cm water through a duct 300 mm diameter and discharges it through a duct of 275 mm diameter. Determine the static fan efficiency IN PERCENT if total fan mechanical is 75 percent and air is measured at 25 deg. Celsius and 760 mm Hg.
A fluid enters a pipe at speed v1=0.1 m/s. the diameter of the tube is d=200mm and the fluid flowing through the pipe is mercury with a specific gravity of 13.6. the mass flow rate is
a fan draws 1.42m3 per second of air at a static pressure of 2.54 cm of water through a duct 300 mm diameter and discharges it through a duct of 275 mm diameter. Determine the static fan efficiency if total fan is 75% and air is measured at 25 degree celsius and 760 mm Hg
A centrifugal pump is required to deliver 50 liters of water per second to a height or 30 m through a 100 m long pipe of 15 cm diameter. The inlet losses in the suction pipe are estimated to be 0.35 m. Assuming an overall efficiency of 70 percent and taking Darcy’s friction coefficient of 0.015 for the pipeline, determine the power, in kW, required to drive the pump.
The refrigerant R134a is passing through the diffuser with the inlet diameter of D1=1 inch; p1=150psi; and V1=1000 ft/s as a saturated vapor. The exit parameters are p2=400 psi, and velocity V2=0.5 ft/s. Heat transfer, Work, and Potential energy changes can be neglected. NOTE: Use English units. For the kinetic energy change do not forget dividing to (778*32.2) conversion factor to obtain Btu/lbm. From NIST tables use BTU/lbm units for the enthalpy. Determine: a.Exit temperature in F; b.Mass flow rate in lbm/s; c.Exit diameter D2 in inches. d.Determine exit temperature.
The refrigerant R134a is passing through the diffuser with the inlet diameter of D1=1 inch; p1=150psi; and V1=1000 ft/s as a saturated vapor. The exit parameters are p2=400 psi, and velocity V2=0.5 ft/s. Heat transfer, Work, and Potential energy changes can be neglected. NOTE: Use English units. For the kinetic energy change do not forget dividing to (778*32.2) conversion factor to obtain Btu/lbm. From NIST tables use BTU/lbm units for the enthalpy. Determine: a.Exit temperature in F; b.Mass flow rate in lbm/s; c.Exit diameter D2 in inches. d.Determine exit temperature. show and expalin each step please
Determine the static fan efficiency if total fan mechanical efficiency is 70% and air is measured at 25 deg C and 760 mmHg for a fan that draws 1.42 cubic meters of air per second at a static pressure of 2.54 cm of water through a duct 300 mm diameter and discharges it through a duct of 275 mm diameter.
Water at 60 deg. F is pumped from a reservoir to the top of a mountain through a 6-in SCH 120 pipe at an average velocity of 12 ft/s. The pipe discharges into the atmosphere at a level 3000 ft above the level in the reservoir. The pipeline itself is 4500 ft. long. If the overall efficiency of the pump and the motor driving it is 70% and the cost of electric energy to the motor is 4 cents per kilowatt-hour,1. what is the hourly energy cost for pumping this water? $3.21$ 18.32$12.83$81.23$ 32.18$23.81none of the given
In an hydroelectric plant, 100 m^3/s of water flows from elevation of 120 m to a turbine, where electric power is generated. The overall efficiency of the turbine-generator is 80 percent Disregarding frictional losses in piping. Estimate the electric power output of this plant.
Answer this ASAP plz Air enters a pipe with a diameter of 3 cm and a length of 17 m with a speed of V1 = 75 m/s, pressure P₁ = 600 kPa and T₁ = 60 °C and a friction factor of 0.025. Count: a. V2, P2, T2 and po2 at the end of the pipe. b. What is the additional length of the pipe that causes the outflow to be sonic.
3. In a refinery, certain oil with sp.gr 0.9 flows with a velocity of 2 m/s in a pipe of diameter 30cm. Along the flow, the pipe diameter gets reduced to 25 cm. Determine the velocity and mass flow rate of oil at this section. 4. A circular pipe of uniform diameter 500mm carries water under pressure 30 N/cm2 . The mean velocity of water at the inlet (at the datum) is 2.0 m/s. Find the total head or total energy per unit weight of the water at a cross-section, which is 5 m above the datum line. 5. A tapered pipe, through which water is flowing, is having diameter, 30cm and 20 cm at the cross-sections 1 and 2 respectively. The velocity of water at section 1 is given as 3.5m/s. Find the velocity head at section 1 and 2 and also rate of discharge. 6. Water is flowing through a pipe having diameter 300mm and 200 mm at the bottom and upper end respectively. The pressure at the lower(bigger) end is 25 N/cm2 and the pressure at the upper end is 10 N/cm2. Determine the difference in datum…