A of 0.06 melrar, nuns into a taukhtabeThe tabe inclu des aUnder yoressure,Valve, a wreneh, a el bowTheabruptflicient areand aninlet,minon los coeE heE lhz = G.9 . Friction hasgrouped asbeen calculoted asThe=002.faucet is pe quired to provide am ainlow of 10/sDeter mine thepressure needed in the waten tanthto supply this f low.

Name: A of 0.06 melrar, nuns into a taukhtabeThe tabe inclu des aUnder yore
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A of 0.06 melrar, nuns into a taukhtabeThe tabe inclu des aUnder yoressure,Valve, a wreneh, a el bowTheabruptflicient areand aninlet,minon los coeE heE lhz = G.9 . Friction hasgrouped asbeen calculoted asThe=002.faucet is pe quired to provide am ain

Given data: - The diameter of the tube is d = 0.06 m. The minor loss coefficient is hL = 6.8. The…

Engineering

Mechanical Engineering

A tube of 0.0G metrar, nuas into a tanth under pressune. The tube incl. des a abrupt The minor loss cop flicient are E hz = G.8. Friction has Valve, a wreneh, en el bow and an inlet, grouped as been calculoted as faucet is Me guired to provide an ain low oA 10/s The O02. 10 7/s Deter mine the yoressure needed in the waten tanh to supply this Plow.

A tube of 0.0G metrar, nuas into a tanth under pressune. The tube incl. des a abrupt The minor loss cop flicient are E hz = G.8. Friction has Valve, a wreneh, en el bow and an inlet, grouped as been calculoted as faucet is Me guired to provide an ain low oA 10/s The O02. 10 7/s Deter mine the yoressure needed in the waten tanh to supply this Plow.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The engine is connected to a dynamometer which gives a brake output torque of 200 N-m at 3600 RPM. At this speed air enters the cylinders at 85 kPa and 60°C and the mechanical efficiency of the engine is 80%. Find out power lost in friction. Assume necessary data which is not given in question. Vd = .002 m3 B = .08 m
1. A pelton type turbine was installed 30 m below the head gate of the penstock. The head loss due to friction is15% of the given elevation. The length of the penstock is 80 m and the coefficient of friction is 0.00093.Determinea) the diameter of the penstock in mm. (421.6 mm)b) the power output in KW (781.234 KW)
Determine the percentage decrease in the volume of waterin a hydraulic press. It is initially at 137 kPa and then subjectedto a pressure of 116, 280 kPa. Use E=2.5 GPa. ΔV / V = ?
Pls. answer thank you! A pelton type turbine was installed 31m below the head gate of the penstock. The head loss due to friction is 15% of the given elevation. The length of the penstock is 80 m and the coefficient of friction is 0.00093 (Morse). Determine the diameter in meters of the penstock and the power output in KW.
A water pump dissipates power on the shaft N=5.5 kW. Refine parameters: Head, flow and efficiency of the pump. Knowing the residual pressure Pair = 20, open the pump outlet (head) and the vacuum pressure at the inlet Pa,= 4m (head). The velocity in the thrust tube v2=4 m/s, the ejector tube diameter 75 mm, the suction pipe diameter 100 mm and the difference between the vacuum gauge and the manometer zero. Kinetic correction factor, geometry (Z2) -Z0). Ignore the height POST
ity of 25 m/s. 1 he pressures; Iy while the datum head at WJ A pipe of diameter 400 mm carries water L oints A and B are given as 29.43 Nfem” and 22.563 Nfcm respective B are 28 m and 30 m. Find the loss of head betweert A and B
In this problem should we add the friction losses in Bernoullis equation ? also, shouldnt we divide by gc=32.17? Please help, I'm confused
Li10 a. the friction loss (A P ) in the main .duct (A) 0.6m*/s
A compressor takes in refrigerant at a pressure of 80.34 psia. The dischargepressure of the refrigerant is 281.74 psia. What is the compression ratio ofthe compressor? Round the answer to the nearer tenth.
5.10 The water is supplied at the rate of 3 m3 per minute from a height of 4 m to a hydraulic ram, which raises 0.3 m3/minute to a height of 30 m from the ram. The length and diameter of the delivery pipe is 100 m and 70 mm respectively. Determine the D' Aubuisson's efficiency of the hydraulic ram if the co-efficiency of friction f = .009.
A vertical steel stand-pipe (a cylindrical tankopen at the top and having a vertical axis), is3m in inside diameter and 30 m high. The tankis filled with water having a weight density of104 N/m3. The material is structural steel havinga yield point of 270 MPa and a safety factor of2 is to be used. (a)What is the requiredthickness in terms of millimeters, of steel platenecessary at the bottom of the tank if thewelded longitudinal seam is presumed to be asstrong as the solid metal? (b) What wallthickness in terms of millimeters, is required ifthe seam is only 72% as strong as the solidmetal?
The old Hydraulics laboratory in Mechanical Engineering used a roof tank tosupply apparatus with water at a nearly constant head. The water wascollected in an under floor sump, and then pumped back to the roof tankafter the experiment. The flow rate was 10 litre s-1. The tank was 6m abovethe sump, and the length of the pipe route was 15 m. The old 6” pipes arenow heavily corroded (k = 7.5 mm). The old pump has been scrapped. Whathead ΔH would be specified for a pump to restore the system using the oldpipes? What would the pump power be? If the pipes were replaced with 150mm diameter PVC pipes, what pump ΔH would be required?