A U-tube is made up of two capillaries of bores 1.2 m and 2.4 mm respectively. Q9) The tube is held vertical and partially filled with liquid of surface tension 0.06 N/m and zero contact angle. If the estimated difference in the level of two menisci is 15 mm, determine the mass density of the liquid.

A U-tube is made up of two capillaries of bores 1.2 m and 2.4 mm respectively. Q9) The tube is held vertical and partially filled with liquid of surface tension 0.06 N/m and zero contact angle. If the estimated difference in the level of two menisci is 15 mm, determine the mass density of the liquid.

Name: A U-tube is made up of two capillaries of bores 1.2 m and 2.4 mm resp
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A U-tube is made up of two capillaries of bores 1.2 m and 2.4 mm respectively.Q9)The tube is held vertical and partially filled with liquid of surface tension 0.06 N/m and zero contactangle. If the estimated difference in the level of two menisci is

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

two vertical parallel glass plates 0.1 mm apart are partially immersed in water. Considering that the water does not reach the upper edges of the sheets and that the liquid completely wets the glass, determine: a) the height that rises in the flat capillary, b) the attractive force between the plates. Consider the width of the sheet l=12cm and density y=72.8*10^-3 N/m
To what height will 68˚F ethyl alcohol rise in a 0.005 in internal diameter glass capillary tube? The density of the alcohol is 49 lbm/ft3 note ? = 0.00156 ???/ ?? and ? = 0°.
Two small vessels are connected to a U-tube manometercontaining mercury(relative density 13.56) and the connectingtubes are filled with alcohol (relative density 0.82). Thevessel at the higher pressure is 2 m lower in elevation than theother. What is the pressure difference between the vessels whenthe steady difference in level of themercury menisci is 225 mm?What is the difference of piezometric head? If an inverted U-tubemanometer containing a liquid of relative density 0.74 wereused instead, whatwould be the manometer reading for thesame pressure difference?
Determine the maximum capillary rise (h) that can be expected from water at 4°C, between two clean glass plates. ri=8.0mm
Derive a formula for capillary rise (h) between two concentric glass tubes of radiuses RI and R2. determine its value for water if (G. = 0.072 N/m, RI=30mm, & R2=36mm) (Take smooth and very clean glass tubes).
Derive an expression for the capillary- height change h, as shown, for a fluid of surface tension Y and contact angle 0 be- tween two parallel plates W apart. Evaluate for water at 20°C if W = 0.5 mm.
A block of wood floats in water with 45 mm projecting above the water’s surface. When placed in glycerine of Relative Density (RD) 1.34, the block projects 70 mm above the surface of that liquid. Determine the density of the wood
An oil tanker 3m wide 2 m deep and 10 m long contains oil of density 800 kg/m3, if the tanker is closed and completely filled with the oil and accelerated horizontally at 3m/s2. a.) determine the total liquid thrust (hydrostatic force) on the front end. (in kN) b.) determine the total liquid thrust (hydrostatic force) on the rear end. (in kN)
Capillary rise in the glass tube used for measuring water level isnot to exceed 0.5 mm. Determine its minimum size, given thatsurface tension for water in contact with air = 0.07112 N/m.
An open cylindrical vessel 60cm in diameter and 1.20m high contains water to a depth of 1m. If it is rotated about its vertical axis, determine the angular velocity w if: a)The water surface just touches the edge of the open top without spillage.
The gage pressure of air in a pressurized water tank is measured simultaneously by both a pressuregage and a manometer. The differential height h of the mercury column is to be determined. Assumptions The air pressure in the tank is uniform (i.e., its variation with elevation is negligible dueto its low density), and thus the pressure at the air-water interface is the same as the indicated gagepressure.
A tank of water 4 m deep receives a constant upwardacceleration a z . Determine ( a ) the gage pressure at the tankbottom if a z = 5 m 2 /s and ( b ) the value of a z that causes thegage pressure at the tank bottom to be 1 atm.